Life Smart S-LPHW-3 Guide

PORTABLE INFRARED HEATER

OWNER’S MANUAL AND USER GUIDE

Model No. S-LPHW-3

WARNING: READ THIS ENTIRE OWNER’S MANUAL CAREFULLY BEFORE USE.

Thank you for choosing a Lifesmart Infrared Heater. This owner’s manual will provide you with valuable

information necessary for the proper care and maintenance of your new product. Please take a few moments

to thoroughly read the instructions and familiarize yourself with all the operational aspects of your new

heater.

PLEASE SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

READ AND UNDERSTAND ALL INSTRUCTIONS, SAFETY WARNINGS,

AND FAQ’s BEFORE USING THE HEATER

WARNING!

! POTENTIAL FOR ELECTRICAL HAZARD IF NOT ADHERED TO!

When using electrical appliances, basic precautions should always be followed to reduce the

risk of fire, electric shock, and injury to persons, including the following:

1. This heater must be plugged into a 120V, 15 amp (or more) circuit of its own. Nothing

else can be plugged into the same circuit. If unsure if your home meets this

specification, consult a certified electrician prior to use. Risk of fire, overheat,

malfunction, property damage, injury, or even death may result if not adhered to!

2. Connect to a properly grounded, 3-prong outlet only. Do not connect the heater to

extension cords, surge protectors, timers, direct breakers, or an outlet with other

appliances connected to the same outlet. Risk of fire, overheat, malfunction,

property damage, injury, or even death may result if not adhered to!

3. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces.

Use handles (certain models) or wheels to move this heater.

4. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and

curtains at least 3 feet (0.9m) from the front of the heater and keep them away from the

sides and rear of the heater.

5. Extreme caution is necessary when any heater is used by or near children, invalids,

pets, or when the heater is left operating unattended.

6. Always unplug the heater when not in use.

7. Do not operate any heater with a damaged cord or plug or after the heater malfunctions,

has been dropped, or damaged in any manner. Contact the manufacturer for resolution

options.

8. Do not use outdoors. Exposure to outdoor elements such as rain, snow, sun, wind or

extreme temperatures may cause the heater to become a safety hazard.

9. This heater is not intended for use in bathrooms, laundry areas and similar indoor

locations, nor any locations that use GFCI outlets.

10.Never place heater where it may fall into a bathtub or other water receptacles.

11.Do not run cord under carpet. Do not cover cord with throw rugs, runners, or similar

coverings. Arrange cord away from traffic area and where it will not be tripped over.

12.The heater must be plugged into a wall outlet that is a DEDICATED CIRCUIT, with a

minimum 15 amp rating on that individual circuit.

13.To disconnect the heater: FIRST, turn the power button to the “off” position, then

remove plug from the wall outlet.

14.Do not allow foreign objects to enter or block any ventilation or exhaust opening as this

may cause an electric shock or fire, or damage the heater.

15.Allow at least 3 feet of unobstructed space to the front and rear of the heater to allow for

maximum heat, air, and ventilation flow.

16.A heater has hot and arcing or sparking parts inside. Do not use it in areas where

gasoline, paint, or flammable liquids are used or stored, nor use flammable solvents to

clean the heater. Also, make sure to keep heater dry at all times.

17.Use this heater only as described in this manual. Any other use not recommended by

the manufacturer may cause fire, electric shock, or injury to persons.

18.Do not use abrasive solvents to clean the heater as it may cause damage to the finish

or casing.

PLEASE REVIEW FREQUENTLY ASKED QUESTIONS ON THE NEXT

FEW PAGES PRIOR TO USING YOUR HEATER.

FREQUENTLY ASKED QUESTIONS (FAQ’S)

My heater emits a “strange” odor when I first open the box/when I turn the heater on for the first

time. Why is this happening?

This is normal. This heater is treated with a special heat safe/resistant coating. This odor will

sometimes be present when the box is opened, and may be compared to a heaters version of “new

car smell.” Also, similar to all hearth appliances (woodstoves, etc.), the coating, exposed to heat, will

produce this particular odor during the first few hours of operation. This will dissipate after the break-

in period. If you are sensitive to odors, you may want to pre-burn the unit in a garage with the

door open until the initial odor dissipates.

If my heater runs on approximately1500 Watts, how many BTU’s is that? Is that a lot of heat?

At 1500 Watts, your heater will use approximately 5100 BTUs. 5100 BTUs, compared to your home

furnace, is a very small amount of heat (this heater is intended to be used as supplemental heat in

areas most needed). It may take several minutes, to several hours to heat your area, depending on

various factors (see Heater Placement).

Can my heater really operate on less money per day? What are my operating costs?

Yes. If the heater is used as it is intended (as supplement/assist heat), it should cycle on and off,

allowing for it to heat a total of approximately 8 out of the 24 hours of the day. Using the national

average of approximately 10¢ per kWh (look at your bill for exact cost per kWh--will vary per state),

your average heating cost (add a few cents just for having it plugged in) should be less per day

compared to your main furnace. The costs will increase if it is used as the single source of heat, or if

heat somehow escapes the room being heated, since the “on” cycle will run longer.

The Formula: To determine the cost of this or ANY 1500 watt appliance, multiply 1.5 X your cost per

Kilowatt Hour to determine approximately how much it costs you to run the heater. You can find the

cost per KWH prices for your state at: http://www.eia.doe.gov/fuelelectric.html

What is the life expectancy for the Heating Elements? Can the heating elements be replaced?

The life expectancy of the heating elements is typically 25,000 hours. Heating elements may be

replaced by obtaining parts from the Manufacturer, although it is not recommended, due to the

amount of work (unless you are a certified heater technician or authorized directly by LIFESMART

Technical Support). All parts may be purchased through LIFESMART if your product is out of

warranty. Note: If you feel that the elements are definitely faulty right out of the box, contact the

LIFESMART Technical Support department first (for troubleshooting and verification).They can then

direct you on to the next step.

Once I plug the unit in and turn it on, how long will it take to heat my room?

The heating process in the heater begins immediately upon powering on, and setting the desired

temperature above the ambient temperature. A noticeable change in the l room’s ambient

temperature will vary. Remember that with any type of heating process, there are many variables:

Location of heater (in the home), floor plan and size of the room, how well the room is insulated, how

many doors/windows, how much bare concrete (acts as a heat sink with any type of heating), the

opening and closing of an exterior door, long hallways, high ceilings, etc. Customers with smaller

rooms experience quick heat changes. Rooms with larger and open floor plans can expect up to 24

hours to completely heat up.

I don’t have a grounded outlet; can I use adapters, a 2-prong power strip, or remove the ground

prong from the cord?

Definitely NOT! If you don’t have a grounded outlet, contact a certified electrician for advice.

Removing or altering any part of the heater’s original design or intent (including the power cord) will

not only void the warranty, but will make you liable for any unexpected or hazardous results.

Why doesn’t the temperature on my heater match the temperature display on my wall, or external

thermostat?

This is completely normal. The temperature display on your heater may vary from the temperature

display on another thermostat (like the one mounted to your wall or a purchased external thermostat).

This is because the temperature sensor on the heater reads the temperature directly around the

heater. With the heater near the cold floor (and heat rising), any readings on elevated or external

thermostats will differ in readings on the heater. The best way to operate your heater is just to set

the unit on “High” and dial up to a temperature that feels comfortable to you. Then, leave it at that

temperature, regardless of the mismatch. The heater will cycle off when the set temperature is met or

exceeded slightly.

My home is not insulated very well, will this heater help me? Can I use the heater if I have vaulted or

cathedral ceilings? I live in a structure that is larger than 800 square feet. Will this heater help me? Can I

use the heater to heat multiple rooms at the same time? Will I be able to use the heater in a basement or

garage?

The answer to these is the same. Yes. You will be able to use it, but keep in mind that

rooms/structures with open floor plans, minimal insulation, adjacent rooms, or high ceilings will not

retain the heat as efficiently, and noticeable heat changes will come slowly. Also, the heater will stay

on for longer periods of time (since it takes so long to cycle off), and may increase your electric costs.

Note that if you do use it in a garage or basement, the moisture levels must be very low and the

heater must have a dedicated circuit (15 amps minimum) with no GFCI outlets being used. If unsure

what a GFCI outlet is, contact a certified electrician.

Can I use more than one heater at a time? Can I use the heater and another appliance at the same time?

Yes. But make sure they are not plugged into the same circuit. Each heater (heaters are considered

appliances, and draw out high amperage) requires its own minimum 15 amp circuit (with no other

items plugged into that circuit or outlet). If unsure your circuit meets these requirements, verify

with a certified electrician. Risk of fire, damage to property, or injury may result if requirements

are not met.

Why does my heater’s fan continue to run after the set temperature is reached or the power is turned

off?

This is normal. The heater’s fan will continue to run, even after the heater automatically cycles

down. The fan continues to run so that every last bit of heat is blown out of the heat chamber, while

allowing the unit to continue filtering your air. Once the internal box/components cool completely, the

fan should then shut off on its own. In this case, allow a few minutes after the heat cycles off (with

power on). The fan will shut off faster when the power is turned off.

Why doesn’t the fan speed increase when I change the setting from Low to High?

This is normal. The heater’s fan’s speed is not affected by the High/Low settings. The fan is

designed to vent the heat at one soft, comfortable, and energy efficient speed. What is affected by

the High setting is the heat output. In essence, in the High mode, the heater produces “more” heat,

rather than “faster” heat.

I want to make sure my warranty is registered. What do I send to make sure it is registered? Where

do I send it?

The heater comes with an automatic 1 year limited manufacturer’s warranty at the time of purchase.

Your receipt is considered your proof of purchase and registration. Keep it in a safe place. As long

as it is legible, a copy may be used for any future warranty claims (if requested). If you have access

to e-mail, and would like peace of mind, e-mail us to: [email protected] In the

body of the e-mail, include your full name, address, phone number, model, serial number, and

scanned copy of your legible receipt. You may also register in the “registration” tab at:

www.lifesmartproducts.com

My heater does not perform as well as another brand heater that I purchased. Why Not?

There are many brands of heaters on the market. Each brand is designed with different heat

specifications, designs, trademarks, fan speeds, colors, material types, displays, and electrical

components. They are manufactured this way for you, as the consumer to have choices, selection,

and preferences. As long as the unit functions as specifications indicate, comparison to other brands

will ultimately depend on individual consumer perception.

I purchased my heater so that it could cut my heating costs, but my electric bill has gone up. Why?

The compact LIFESMART heater can definitely save you on heating costs, when compared to the

existing central heating system in your home, and when used as supplemental heat. Your heater is

designed to give your main heat source a supplement “boost,” or allow for you to have extra heat (in

the form of soft infrared waves) in locations where you would otherwise be short. It is meant to cycle

on and off as it provides the central heat the boost it needs. If you intend on using it as a single heat

source, especially in larger homes (which you may), expect the heater to 1) take as much as 24

hours to heat the area, 2) stay on for longer periods of time (without cycling off) due to heat loss, and

3) increased use time, and electric costs.

My heater’s display shows my ambient temperature to be in the 20’s, when I know it is warmer than that.

Why?

The heater’s display is defaulted to read the temperature as Fahrenheit. If your heater is definitely

heating, but shows it is in the 20’s, you probably have the setting to read your temperature in Celsius,

rather than Fahrenheit. See Users Guide to change.

My heater has a temperature setting indicating ECO. It is supposed to be efficient, but it seems to not heat as

much. Why?

The ECO mode on your heater is a program that attempts to keep the temperature strictly at a

“warm” 68° F. This also helps with efficiency, as it is programmed to 1) Increase the wattage used to

1500W if the temperature drops below 64.4°F 2) Gradually reduce the wattage used as it approaches

66.2° F and 3) Stop heating when 68° F is achieved. This is considered an Economical function,

since in the ECO setting, the heater is almost never running on the full 1500 Watts. If this “warm”

heat is not plentiful or is “On” constantly, and you fear it will increase your electric bills, we

recommend you set it to the High or Low setting and have it cycle off when your set temperature is

achieved. You may also set the timer to allow your heater to shut off at the given hour increments you

desire. See User’s Guide to set the timer.

SPECIFICATIONS

Voltage Rating

120 V (60Hz)

Power Consumption

1500W

Unit Size

13.4in. (W) x 15in. (D) x 8.46in. (H)

Unit Weight

19.84 lbs

SAFETY FEATURES

Tip-Over Safety Feature

This heater is equipped with a tip-over safety feature. Once the heater is tipped over, an internal switch will

automatically shut the heater off. Once the heater is restored an upright position, the heater will reset. To

continue operation, turn on the heater using the supplied remote control or the control panel on the heater.

Overheat Safety Feature

This heater is equipped with a overheat safety feature. When the heater’s internal components reach a

certain temperature that could cause overheating or possible fire, the heater will automatically shut off.

WARNING: It is normal for the power cord to feel warm to touch; however, a loose fit between the outlet

and the plug may cause overheating of the plug. If this occurs, try inserting the plug into a different outlet.

Contact a qualified electrician to inspect the original outlet for damage.

IN THE BOX

·INFRARED HEATER

·REMOTE CONTROL (2 AAA Batteries Sold Separately)

·INSTRUCTION BOOKLET

PRODUCT DIAGRAM

Control Panel

Air Intake (Vent)

Master

Power Switch

Remote Control

Filter Cover

Temperature Sensor

Air Outlet (Vent)

FRONT

VIEW

REAR

VIEW

Wooden Cabinet

Foot pad

1. Timer button: Used to engage timer mode and to set hour value for the timer

2. Mode button: To select between High, Low, and Eco modes

3. Power Switch Button: Powers the display on and off

4. Power indicator light: Indicates that the heater is receiving power from outlet. Will flash when

powered “ON’

5. High Mode indicator light: Will be lit when High Heat mode is engaged

6. Digital display: Indicates set desired room temperature

7. Celsius indicator light: Will be lit when temperature displayed is in Celsius

8. Remote control signal sensor

9. Temperature Up button: To increase desired temperature

10. Temperature Down button: To decrease desired temperature

11. ℃/℉Button: Alternates between Fahrenheit and Celsius

12. Timer indicator light: Will be lit when the Timer is engaged and active

13. Fahrenheit indicator light: Will be lit when temperature displayed is in Fahrenheit

14. Energy-saving mode (ECO) indicator: Will be lit when ECO mode is engaged

15. Low Mode indicator light: Will be lit when Low Heat mode is engaged

Table of contents

Other Life Smart Heater manuals

Life Smart

Life Smart HT1289 User manual

Life Smart

Life Smart LS-3W-BPIQT User manual

Life Smart

Life Smart LS-1000X-4M User manual

Life Smart

Life Smart XXHT1141US User manual

Life Smart

Life Smart LS-1000X-4W User manual

Life Smart

Life Smart LS1006HH13 Quick start guide

Life Smart

Life Smart LS-6BPIQH-X Quick start guide

Life Smart

Life Smart LS-6BPIQH-X Quick start guide

Life Smart

Life Smart SH37 User manual

Life Smart

Life Smart R-LS-W6-WIQH-M User manual

Life Smart

Life Smart YAA02E-5 Quick start guide

Life Smart

Life Smart L-SIFST-S Quick start guide

Life Smart

Life Smart LCHT0016US User manual

Life Smart

Life Smart LS1000HH13 Quick start guide

Life Smart

Life Smart LS-3ECO User manual

Life Smart

Life Smart LS-1000X-6W Quick start guide

Life Smart

Life Smart LS-8WIQH-DB Quick start guide

Life Smart

Life Smart LS-500-1WP Quick start guide

Life Smart

Life Smart LS-PH08H Operator's manual

Life Smart

Life Smart LS-PP1500-6NAT User manual

Life Smart

Life Smart LS-1500X-6WB Quick start guide

Life Smart

Life Smart REFURBISHED R-W-19 User manual

Life Smart

Life Smart R-HT1156 User manual

Life Smart

Life Smart LS‐Stealth‐6 User manual

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide