Life Smart LS-IF1500-MOFP Quick start guide

1



Infrared Fireplace Heater

OWNERS INSTALLATION AND OPERATING MANUAL

Model: LS-IF1500-MOFP

Safety Notice

Please read this entire Installation and Operating Manual BEFORE installing and using your new

Infrared Fireplace Heater. Failure to fully understand and follow instructions may result in property

damage, bodily injury, or even death.

If your Infrared fireplace heater is not used properly, a house fire may result. For everyone’s safety,

FOLLOW all Installation and Operating Directions. Infrared fireplace heaters have been designed

for use in the US and are suitable for mobile homes.

Save These Instructions

2



TABLE OF CONTENTS

Topic Page(s)

Introduction 3

Specifications 3

Safety Information 4-5

Fireplace Placement 6

Fireplace Operation 7

Troubleshooting and Fireplace Maintenance 8

Warranty 9-10

Warranty Claim Contact Information 11

3



INTRODUCTION

Thank you for choosing one of the best Infrared absorption fireplace heaters available in the

market today. By using this infrared fireplace heater you can efficiently heat up to 1500

square feet! You can even turn down the main thermostat in your home and let this heater

carry some of the home heating duty. This fireplace heater is NOT intended to replace your

homes furnace; rather it is designed to be a supplement to it. It is not an instant heater – it

can take up to 24 hours for a room to reach the desired temperature. Our Infrared fireplace

heaters have been tested and listed for installation in residential and mobile homes by UL:

SPECIFICATIONS:

Electrical:

Voltage: 120v~60Hz,

Power consumption: 1000-1500 Watts,

Thermostat range: 50-90 Fahrenheit,

Coverage:

Up to 1,500 square feet

Dimensions:

31.5” x 11.5” x 25.2”, 60 lbs

Safety Features:

Overheat shut off.

Features:

Remote control

Vivid Log/ Flame Effect

Eco Friendly Wood

4



IMPORTANTSAFETYINSTRUCTIONS

READANDUNDERSTANDALLINSTRUCTIONSBEFOREUSINGTHE

HEATER

WARNING

!POTENTIALFORELECTRICALHAZARD!

When using electrical appliances, basic precautions should always be followed to reduce the

risk of fire, electric shock, and injury to persons, including the following:

1. Read all instructions before using this heater.

2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot

surfaces. If provided, use handles when moving this heater. Keep combustible

materials, such as furniture, pillows, bedding, papers, clothes, and curtains at

least 3 feet, from the front of the heater and keep them away from the sides and

rear.

3. Extreme caution is necessary when any heater is used by or near children or

invalids and whenever the heater is left operating and unattended.

4. Always unplug heater when not in use.

5. Do not operate any heater with a damaged cord or plug or after the heater

malfunctions, has been dropped or damaged in any manner. Return heater to

authorized service facility for examination, electrical or mechanical adjustment, or

repair.

6. Do not use outdoors.

7. This heater is not intended for use in bathrooms, laundry areas and similar indoor

locations. Never locate heater where it may fall into a bathtub or other water

container.

8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or

similar coverings. Arrange cord away from traffic area and where it will not be

tripped over.

9. To disconnect heater, turn controls to off, then remove plug from outlet.

10. Connect to properly grounded outlets only.

11. Do not insert or allow foreign objects to enter any ventilation or exhaust opening

as this may cause an electric shock or fire, or damage the heater.

12. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do

not use on soft surfaces, like a bed, where openings may become blocked.

13. A heater has hot and arcing or sparking parts inside. Do not use it in areas where

gasoline, paint, or flammable liquids are used or stored.

14. Use this heater only as described in this manual. Any other use not recommended

by the manufacturer may cause fire, electric shock, or injury to persons.

5



15. Always plug heaters directly into a wall outlet/receptacle. Never use with an

extension cord or re-locatable power tap (outlet/power strip).



This heater has a self – protection function. If the heater does not operate

normally, check cord and heater placement, then UNPLUG IT FROM THE

OUTLET & PLUG IT BACK TO OUTLET TO RESET.



Grounding

This heater is for use on 120 volts. The cord has a plug with three blades for proper

grounding. DO NOT attempt to modify the plug in any way or use adaptors to defeat the

purpose of the grounding feature. Plug ONLY into a receptacle that accepts three-blade plug.

6



FIREPLACE PLACEMENT

Our Infrared fireplace heater is a very safe and effective room heater. It produces safe, clean

and economical heat by utilizing quartz infrared heating elements and heat exchangers. The

heating process of the Infrared fireplace heater is similar to the way the sun warms the earth.

The infrared elements warm the heat exchangers and the whisper quiet fan distributes the

accumulated warmth. This process is unique among heaters in that it minimizes wasteful

heat collection at the ceiling height of rooms and targets it toward the living space instead.

To achieve maximum efficiency of your Model LS-IF1500-MOFP Infrared fireplace heater,

please consider the following recommendations:

1. Locate your Infrared fireplace heater close to an inside wall of the room in which it will be

used. Face the exhaust vents of the heater toward the cooler outside walls of the house.

This positioning will allow the heat to be moved across the room toward the outside walls

to provide more even warmth throughout the room.

2. Make sure that windows and doors are not allowing a high rate of airflow into the room

where you will locate your room heater. High airflow will minimize the effectiveness of

your Infrared fireplace heater as it would any conventional type heater.

3. For best results, always try to maintain a minimum of 40% relative humidity in the

environment to be heated.

4. It is recommended that the Infrared fireplace heater be used in rooms that are insulated

according to code. You can use your heater in a room whether insulated or not, but a non-

insulated room will cause greater and faster heat loss which is counterproductive to the

efficiency of the heater.

5. Keep the area around the heater clear of clutter and obstacles so that there is free airflow

to and from the heater.

6. Be mindful to keep your heater out of the main traffic thoroughfares of the room in which it

is located; it should be a welcome addition to the room rather than an obstacle to be

stepped over or stepped around.

7



ControlPanel



 

RemoteControl

FIREPLACE OPERATION

Plug your Infrared fireplace heater power cord into a 120V, 15amp or 20amp three-bladed receptacle.

To Turn the Fireplace On: Press the Power button on the control panel or on the remote

control.

Default Set Temperature: The default set

temperature every time the heater is powered on is

typically 72°. This default cannot be changed. You

will have to set it accordingly every time you power

it off.

Ambient Temperature: To view the ambient room

temperature, press and hold the Temp up

button for a few seconds, the room temperature will

display for a short period of time, then return to the

desired set temperature.

To Set Desired Temperature:

Press the UP or DOWN button on the

control panel or on the remote control. When the

desired set temperature is reached by the heater’s

internal thermostat, the heater will stop heating

automatically, but the fan will continue to run for

approximately 5 minutes (3 minutes when powered

off) so that unit’s chamber can cool. When the

ambient temperature drops below the set desired

temperature, the heater will cycle on again.

To Set Heat Level: Press the heat button on

the control panel or remote control to switch between High and Low heat. The corresponding

High (H) or Low (L) light will switch on. In the High mode, the fan will not change speeds.

Rather, the heating elements will allow for higher heat output. The High level uses 1500 watts,

while Low heat level uses approximately 1000 watts.

To change between °Celsius and °Fahrenheit: Press

To Set Flame Brightness: Use the Dimmer button on the control panel or remote

control. The flame brightness control button is used to increase or decrease the brightness of

the flame and ember. Press once, the brightness will start and keep changing. Press

again to set the desired level.

8



TROUBLESHOOTING

If your heater unit shuts off unexpectedly:

1. Be sure the power cord is plugged into a working electrical outlet.

2. Check for any obstructions. If you f ind one, turn the heart ing unit OFF and unp lug it. Wait a t least

10 minutes to allow the heating unit to cool completely before removin g any obstruction. Whe n

done, plug in the heating unit and follow the Operation Instructions.

If your heater unit tips over:

1. Set the unit back in its upright p osition and ch eck for any damage is detected u nplug unit a nd

contact customer service for further assistance.

2. If no damage is detected, push the power button to turn the unit back on.

If your fireplace does not illuminate properly:

1. The light bulbs may have vibrated loose and need to be tightened.

2. The light bulbs may be damaged, and need to be replaced.

FIREPLACE MAINTENANCE

WARNING: Disconnect power before attempting any maintenance or cleaning to reduce the risk

of fire, electric shock to persons or damage.

LIGHT BULB REPLACEMENT

Light bulbs need to be replaced when you notice a dark section of the flame or when the clarity and

detail of the log exterior disappears. There are two bulbs under the log set.

WARNING: Allow at least 5 minutes for light bulbs to cool off before touching bulbs to avoid

burning of skin.

BULB REQUIREMENTS

Quantity of 2 clear chandelier or candelabra bulbs with an E-12 (small) socket base, rating voltage 120

volts, rating power 40 watts.

CAUTION: Do not exceed 40 watts per bulb.

CHANGING LIGHT BULBS

Unplug the unit first.

1. Open the light bulb area: Hold left and right side of the cover of the light bulbs at the bottom of your

firebox and pull straight out. You can see two bulbs in the firebox.

2. Examine the bulbs to determine which bulbs require replacement.

3. Remove old bulb and replace with a new one. Hold the socket while unscrewing or screwing bulbs.

4. Replace the cover of light bulbs.

9



Limited Manufacturer Warranty

3 Year Limited Warranty: LIFESMART warrants this heater against defects in materials and

workmanship on functional parts, for a period of 3 years from the original date of purchase. Your sales

receipt showing the date of purchase of the product is your proof of purchase. Keep it in a safe place

for future reference.

Manufacturer Warranty

All LIFESMART products are manufactured with the highest quality materials and are warranted to be

free from defects in material and workmanship at the time of purchase. This limited warranty applies to

products manufactured or distributed by the LIFESMART brand name, are delivered in the continental

United States, and extends to the original purchaser, or gift recipient. This warranty becomes valid at the

time of purchase and terminates either by the specified time frame listed above and/or owner transfer

(unless otherwise authorized by LIFESMART, as the manufacturer). Any extended warranties (warranties

that cover above and beyond this manufacturer warranty) that are sold through a retailer or third party, are

not directly correlated with this LIFESMART limited warranty, and may be redirected to said retailer or

third party for coverage.

Extent of Warranty

This warranty extends through the manufacturer of the product, and covers functional parts only.

Cosmetics are not covered, unless unequivocally determined it is a manufacturer/workmanship defect. Note

that surface cracks are not considered defects in material or workmanship, as they are normal characteristics

of all wood. Unless LIFESMART was the direct shipper, shipping damage should be addressed with the

shipping company, retailer, or place of purchase, prior to making a claim to LIFESMART, as the

manufacturer.

The manufacturer's sole obligation under this warranty shall be limited to furnishing the original purchaser

replacement parts for units deemed repairable by the LIFESMART warranty department. The purchaser

may also opt to ship the product to LIFESMART to have it repaired. The purchaser will be responsible to

prepay any shipping charges (both ways), export taxes, custom duties and taxes, or any other charges

associated with the transportation of the unit. In addition, the purchaser is responsible for insuring any parts

shipped or returned, if desired. For products the warranty department deems un-repairable, or discontinued,

LIFESMART reserves the right to issue a refurbished product, or product similar in size and functionality

as a replacement for the defective unit, if available. All exchanged parts and products replaced under this

warranty will become the property of LIFESMART.LIFESMART reserves the right to change

manufacturers of replacement parts or products for use, in order to cover any existing warranty. Any parts

determined defective may asked to be returned to LIFESMART or its representatives to validate a claim.

Non-Warranty replacement parts will be warranted 30 days from the time the purchaser receives them.

The purchaser must present LIFESMART with proof of purchase documents (including the date of

purchase) if requested. Any evidence of alteration, erasing, or forgery of proof of purchase documents will

be just cause to VOID this limited warranty. Products, in which the serial number has been defaced or

removed, are not eligible for warranty coverage. Continued…

10



Warranty Limitations

This warranty does not apply if the unit has been subject to negligence, fabrication, misuse, abuse, or repairs

(unless authorized verbally, or in writing, by an Authorized LIFESMART Representative) alteration by non

LIFESMART authorized personnel, inappropriate installations, or any case beyond the control of

LIFESMART. Examples of warranty invalidation may also include, but are not limited to:

 Use of lacquer or paints in (and around) the

heaters

 Heater placed on non-approved surfaces

 Electrical requirement deficiencies (15-20

amp dedicated outlet)

 Use on Extension Cords/Timers/Surge

Protectors/GFCI

 Outdoor applications

 Normal wear/tear/weathering

 Pet/Consumer accidents

 Purchases from dealers unauthorized by

LIFESMART (Authorization in writing)

Disclaimers

LIFESMART shall not be liable for any loss due to use (or misuse) of the heater or other LIFESMART

products or other incidental or consequential costs, expense or damages without irrefutable foundations.

Under no circumstances shall LIFESMART or any of its representatives be held liable for injury to any

person or damage to any property, however arising. Any implied warranty shall have duration equal of

the applicable warranty stated above. Specifications are subject to change without notice or obligation.

Legal Remedies

This limited warranty gives the original purchaser specific legal rights. Other rights may vary from

state to state.

Other manuals for LS-IF1500-MOFP

Table of contents

Other Life Smart Heater manuals

Life Smart

Life Smart LS1006HH13 Quick start guide

Life Smart

Life Smart LS-4W1500-X Quick start guide

Life Smart

Life Smart REFURBISHED R-W-19 User manual

Life Smart

Life Smart LS-1000X-4C User manual

Life Smart

Life Smart HT1216 User manual

Life Smart

Life Smart LS-6BPIQH-X Quick start guide

Life Smart

Life Smart LCHT0016US User manual

Life Smart

Life Smart MCHT1153US User manual

Life Smart

Life Smart R-LS-W6-WIQH-M User manual

Life Smart

Life Smart LS‐Stealth‐6 User manual

Life Smart

Life Smart ZCHT1074US User manual

Life Smart

Life Smart LS-3W-BPIQT User manual

Life Smart

Life Smart HT1041 User manual

Life Smart

Life Smart KUH25-01 User manual

Life Smart

Life Smart LS-PP1800-6WCH User manual

Life Smart

Life Smart LS-500-1WP Quick start guide

Life Smart

Life Smart LS-1000X-6W Quick start guide

Life Smart

Life Smart S-LPHW-3 Guide

Life Smart

Life Smart LS-PP1500-6NAT User manual

Life Smart

Life Smart LS-8WQH-DLX13B User manual

Life Smart

Life Smart LS-3ECO User manual

Life Smart

Life Smart HT1193 User manual

Life Smart

Life Smart PCHT1109US User manual

Life Smart

Life Smart L-SIFST-S Quick start guide

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide