Leviton miniZ mZb00-102 User manual
1
miniZ
Quick Start Guide
Congratulations on purchasing the miniZ Daylight
Harvesting Controller. The miniZ is designed to be
easy to install and configure with a few simple steps.
Simplest Install Steps:
1. Physically install unit and any peripherals
2. Terminate power & control wiring
3. Enable AutoCal & Auto Burn-In
4. Power up system
5. Installation & configuration complete!
Supplement this guide with the full installation manual
provided for more advanced applications.
Control Input: US Models 120VAC& 277VAC terminals, Canadian Models 120VAC & 347VAC terminals
Neutral
Circuit 1 Line
Circuit 1 Load
AutoCal – enable
automatic self-calibration
Configuration Jumpers
Switch Inputs
+ Momentary
+ Maintained
+ Supports SPDT Center Off Switches
+Annunciator/Pilot Light Support
Photocell Input
Supplies +24vdc
Expects +0-10vdc return
Occupancy Sensor Input
Supplies +24vdc
Expects +24vdc return
Emergency Input
Also can be configured
as Occupancy Sensor disable
Photocell Disable
Temporarily disables
daylight harvesting mode
Time Clock
Turns off lights
when input receives +24VDC
Load Shed
Lights dim
to shed level when
input receives +24
Daylight Harvesting
Target – Manual
Adjustment
HVAC and/or
Emergency Output
Relays*
Zone 1 Output (0-10V)*
Circuit 2 Line
Circuit 2 Load
Zone 2 Output (0-10V)*
Zone 3 Output (0-10V)*
1/2" nipple for convenient
connection to junction box
*Varies depending on model
Low Voltage Terminal & Configuration Board
Step 1:
Remove the manual and the miniZ product from the box.
2
3
3
miniZ All Models Quick Configuration Guide
REFER TO MANUAL FOR ADVANCED SETUP AND OPERATION
4
4
Step 2:
Refer to the Quick Connection Guides found on pages 11-15 of this
guide to connect the line voltage and low voltage circuits. Select the
diagram based on the model you have purchased.
Note: The dimming models have the 0-10V control output wires leaving the
miniZ controller through the same nipple as the supply and load circuit wires.
They are color coded to different zones as indicated in the manual.
For two zone applications:
•Zone 1 should be connected to the luminaires closest to the daylit area such
as the windows or skylights. This is generally accepted to be approximately
12’ to 15’ from the daylight source.
•Zone 2 should be connected to the luminaires in the next area beyond 15’ to
approximately 25’ from the daylight source.
For three zone applications:
•Zone 1 should be connected to the luminaires closest to the daylight area
such as the windows or skylights. This is generally accepted to be
approximately 8’ to 10’ from the daylight source.
•Zone 2 should be connected to the luminaires in the next area beyond 10’ to
approximately 15’ from the daylight source.
•Zone 3 should be connected to the luminaires beyond the 15’ area.
55
5
Zone #1 receives most effect from daylight
Zone #2 receives moderate effect from daylight
Photocell
Wall Mount
Occupancy
Sensor
miniZ
Windows along exterior wall
120/277v
Zone #3 receives least effect from daylight
S
Typical Classroom
3-Zone miniZ
Application
6
6
Step 3:
Connect the photocell, occupancy sensor (if used), and the wall station
control per the Quick Connect Guides.
Note: The twozone MZD20 can have two separate wall station controls (see
manual) to operate each zone independently in the manual mode only. If only
one wall station control is used, jumper the two switch input terminals to
control both zones.
Step 4:
Turn the power on to the circuit. The luminaires will come on.
77
7
3-zone miniZ Application
2000
2000
ZD31
ZB5
MZ
MZ-2
MZ-1
MZ-3
Fixture Types
105W 0-10V Flourescent
8
miniZ Application
ZD22
ZB5
MZ
MZ-2
MZ-1
10001000
To
Distribution
Panel
Fixture Types
135W 0-10V Flourescent
9
ZD22
ZB5 ZB5
MZ
MZ-2
MZ-1
10001000
To
Distribution
Panel
Dual Room miniZ Application
Fixture Types
135W 0-10V Flourescent
10
Step 5:
In a closed loop configuration, move the Auto-Cal switch to the ON
position as shown in the manual to activate.
Note: This feature operates the luminaires at full output for a period of 24 hours.
During this time, the miniZ will record the lowest foot-candle reading from the photocell
and record that value as the target illumination. The target illumination is the level that
the miniZ will maintain with the load control output as daylight is available to the
space. The lights will automatically raise or lower (dimmed models) based on how
much daylight is contributing to the overall foot-candle value present to the photocell.
Step 7:
Adjust the proportional dimming output (dimmed models only). The miniZ
has proportional dimming using only one photocell input. Tooptimize the
light level balance in the space, adjustment to the daylight harvesting
threshold trim pots may be necessary.
For a 2 zone application:
•The zone closest to the daylight source (zone 1) should be turned to 10 or full
clockwise. The next zone (zone 2) should be adjusted to 4 on the dial. This will
balance the dimming so that the light level across the space is more uniform.
For a 3 zone application:
•The trim pots should be zone 1 = 10, zone 2 = 7 and zone 3 = 3.
Step 6:
If the fluorescent lamps are new, move the Burn-In switch to the ON
position as shown in the manual to activate the 100 hour Burn-In feature.
This will keep the lamps from dimming until 100 hours of operating time.
After that they will operate in the dimmed mode.
Note: Both the Auto-Cal and the Burn-In can occur at the same time.
Other manuals for miniZ mZb00-102
1
This manual suits for next models
17
Other Leviton Controllers manuals
Leviton
Leviton miniZ mZb00-102 User manual
Leviton
Leviton MLC128R User manual
Leviton
Leviton MLC16 User manual
Leviton
Leviton DECORA SURESLIDE 6627 User manual
Leviton
Leviton Decora Smart DW15P User manual
Leviton
Leviton 4200 User manual
Leviton
Leviton Lumina LURPC-01W User manual
Leviton
Leviton Bitwise BWBC2 User manual
Leviton
Leviton 73A00-3ZB Mounting instructions
Leviton
Leviton MS302 User manual
Leviton
Leviton HXC10 User manual
Leviton
Leviton CD250 User manual
Leviton
Leviton DRKDN-U Series User manual
Leviton
Leviton vizia rf+ VRCS1 User manual
Leviton
Leviton vizia rf+ User manual
Leviton
Leviton miniZ mZn20-102 User manual
Leviton
Leviton CN221 User manual
Leviton
Leviton DECORA NE515 User manual
Leviton
Leviton D3208 User guide
Leviton
Leviton RZCZ1 User manual
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
