Leviton MiniZ mZb00-102 User manual

Daylight Harvesting Made Simple.

This user’s guide applies to the following part numbers:

Basic Version, 2 Zone, 2 Relay, 120V or 277V

Basic Version, 2 Zone, 2 Relay, 347V

Dimmed Version, 2 Zone, 2 Relay, 120V or 277V

Dimmed Version, 3 Zone, 1 Relay, 120V or 277V

Description

0-10V

Outputs

Relay

Outputs

mZb00-102

mZd30-101

mZd20-102

mZb00-C02

Model

Number

Features between models vary. As such, not all information in this manual

applies to all models.

Dimmed Version, 3 Zone, 1 Relay, 347V

Dimmed Version, 2 Zone, 2 Relay, 347V 2

mZd20-C02

mZd30-C01

NOTES

Page 1

PHYSICAL INSTALLATION…………………………………………..…….. 2

CONNECT LINE VOLTAGE………………………………………..………. 4

CONNECT LOW VOLTAGE……………………………………………..…. 6

CONNECT LOW VOLTAGE……………………………………………..…. 8

CONFIGURATION DIP SWITCH SETTINGS – BLOCK ONE………………. 10

CONFIGURATION DIP SWITCH SETTINGS – BLOCK TWO….…………… 12

CONFIGURATION DIP SWITCH SETTINGS – BLOCK THREE……………. 15

CONFIGURATION TRIM POT SETTINGS………………………………….. 16

NOTES: DAYLIGHTING CONFIGURATION………………………………… 18

NOTES: BURN IN& AUTO CAL FEATURES……………………………… 19

WARRANTY……………………………………………………………….. 20

DEFAULT TABLES…………………………………..…………………….. 23

TABLE OF CONTENTS

STEP 1

STEP 2

STEP 3

STEP 4

STEP 5

STEP 6

STEP 7

STEP 8

STEP 9

STEP 10

ENCLOSURE FEATURES

The enclosure of the miniZ Power Pack is divided into two compartments.

The Low Voltage Compartment is accessible through the cover-plate.

The High Voltage Compartment is factory sealed and is not accessible.

MOUNTING FEATURES

The Power Pack is suitable for plenum use, indoor only, 0 - 40°C, 5 -

95% humidity without condensation. The supply circuit and load circuits

of the miniZ Power Pack are pre-wired to the control board. Color coded

lead wires are provided for quick connections in a junction box. One ½”

nipple is provided on the top of the Power Pack for this purpose.

There are three concentric knockouts provided in the Low Voltage

Compartment of the miniZ Power Pack. They are combination ½” and ¾”

knockouts. There is one on each of the three external sides of the area.

STEP 1

Page 2

PHYSICAL INSTALLATION

Low Voltage Compartment

This area contains all of the low

voltage terminations required in

the field. All of the configuration

settings are made in this area

as well. Class 2 wiring only.

High Voltage Compartment

This area cannot be accessed in the field.

Lead wires exit the compartment through

the top of the enclosure. There are leads

supplied for field connections to circuits

that energize the miniZ Power Pack and

feed the fluorescent fixture circuits.

Nipple

The fitting on the top of the miniZ Power Pack

attaches directly to a junction box or enclosure.

Two 0.2" mounting holes through the back of the

miniZ low voltage compartment, provide secure

fastening to any flat surface.

Knockouts

There are three concentric

knockouts provided in the Low

Voltage Compartment of the miniZ

Power Pack. They are combination

½” and ¾” knockouts. There is one

on each of the three external sides

of the area.

All connections

are for copper

wire only.

PHYSICAL INSTALLATION

Page 3

Mounting Holes

Two mounting holes are

provided to fasten the

miniZ Power Pack in

place.

CONNECT LINE VOLTAGESTEP 2

JUNCTION BOX

BYOTHERS

SUPPLY CIRCUITS

The Feed Circuit, Relay 1 Line, and

Relay 2 Line can be supplied by the

same circuit or individually. The

connections are made in the junction

box.

All supply circuits must be provided

with a 20A or less branch circuit

overcurrent protection device. Branch

circuit protection for 347V circuits

should be rated at 15A.

Relay 1 Line/Load

Ratings: 20A at 120VAC Tungsten/Ballast

20A at 277VAC Ballast

15A at 347VAC (347V Models Only)

Normally Open, Electrically held.

Color Code: Blue – Line, 12 AWG

Blue – Load, 12 AWG

Control Power Circuit

Voltage Rating: 120 – 277VAC, or

200-347VAC on 347V Models Only

Color Code: Black – Line, 120 – 277VAC, 18 AWG

(120-277V Models Only)

White – Neutral, 18 AWG

Orange – 347VAC, 18 AWG

(347V Models Only)

Load Rating: 10W

Page 4

These circuits must be insulated from

the other wiring even when they are not

being used. Cap off and tape any

unused wires.

Relay 2 Line/Load

Ratings: 20A at 120VAC Tungsten/Ballast

20A at 277VAC Ballast

15A at 347VAC (347VModels Only)

Normally Open, Electrically held.

Color Code: Red – Line, 12 AWG

Red – Load, 12 AWG

Not available on three zone models.

Zone Common

Color Code: Gray – 22 AWG

Not available on Basic Model

Zone 1 Analog Output 0 – 10VDC

Color Code: Violet – 22 AWG

Not available on Basic Model

Zone 2 Analog Output 0 – 10VDC

Color Code: Violet w/White stripe – 22 AWG

Not available on Basic Model

CONNECT LINE VOLTAGE

Page 5

Zone 3 Analog Output 0 – 10VDC

Color Code: White w/Violet stripe – 22 AWG

Only available on Three Zone Model

CONNECT LOW VOLTAGESTEP 3

Page 6

Occupancy Sensor Disabled /

Emergency Input

Label: OCC DISABLE / EMERGENCY

Set by DIP Switch: Block 1 Number 1

This is a +24V input signal. Function can be set to

either mode exclusively.

Occupancy Disable Mode

When the input goes high (+24V) the Power Pack

will disable the Occupancy Sensor input and there

will be no change in the current state. When the

input signal is removed, the Occupancy Sensor will

return to the normal mode.

Emergency Mode

Emergency mode is triggered when the emergency

input is connected to the common. When the signal

is received, the Power Pack will turn on all zones

by turning on all relays and raising any 0 – 10V

outputs to 10 V. The Power Pack zones will remain

fully illuminated until the Emergency signal is

removed.

Photocell Disable / Force Off Input

Label: PC DISABLE / FORCE OFF

Set by DIP Switch: Block 1 Number 2

This is a +24V input signal. Function can be set to

either mode exclusively.

Photocell Disable Mode

When the input goes high (+24V) the Power Pack

will disable the Photocell input, along with daylight

operation, and there will be no change in the

current state. The On switch functionality, when the

photocell is disabled, turns lights on to the

maximum level. When the input signal is removed,

the Photocell will return to the normal mode.

Force Off Mode

When the input goes high (+24V) the Power Pack

will turn off all zones. The Power Pack zones will

remain fully off until the Force Off signal is

removed.

Time Clock Input

Label: CLOCK

This signal will originate from a supervisory time

clock system and is a +24V input signal. When the

input goes high (+24V) the Power Pack will turn off

all zones. If the Blink Warn function has been

configured, the Power Pack will trigger the Blink

Warn cycle. If a switch is used to turn on the lights

during a period that the time clock has the lights

off, the system will go into a Blink Warn override

mode.

If both the Occupancy Sensor and the Time Clock

inputs are used, an active (+24 VDC) signal at the

Time Clock input only has the affect of changing

an Auto On configuration to a Manual On.

CLoad Shed Input

Label: SHED

This signal would originate from an energy

management system and is a +24V input signal.

When the input goes high (+24V) the Power Pack

will reduce the output load levels based upon the

position of the Shed trim pot.

In the event that you are in daylighting mode and

less artificial light is required to meet the target than

is required by load shed, the lights will remain at the

lower lighting level – meeting the target.

CONNECT LOW VOLTAGE

Page 7

STEP 6

All connections

are for copper

wire only.

Label: OCC, +24V, COM

This three position terminal block is dedicated

to the connection of the Occupancy Sensor.

The Occupancy Sensor signal wire connects

to the OCC terminal. This +24V source is

shared with all circuits supplied from the +24V

power supply rated to a maximum of 120 mA.

Occupancy Sensor InputEPhotocell InputF

Label: PHOTO, +24V, COM

This three terminal block is dedicated to the

connection of the Photocell. The Photocell

signal wire connects to the PHOTO terminal.

This +24V source is shared with all circuits

supplied from the +24V power supply rated to

a maximum of 120 mA.

CONNECT LOW VOLTAGESTEP 4

Page 8

Emergency / HVACG

Label: RLY COM, RLY N/O, RLY N/C

There is one Low Voltage relay output rated

for 1A @ 24V which can be switched between

HVAC and Emergency output functionality.

This terminal block is connected to the

Emergency Output / HVAC relay.

Jumper Settings

A three (3) position pin header is located

adjacent to the terminal block. The jumper

configuration of this header determines the

functionality of the relay.

HVAC

A jumper between pins 1 and 2 will result in

HVAC functionality. In this mode the relay will

change state when the room is occupied. In

occupied state NO (normally open) contact is

closed.

Emergency

A jumper between pin 2 and 3 will result in

Emergency output functionality. In this mode

the relay will change state when an

Emergency Input signal is detected. In normal,

non-emergency state the NO (normally open)

contact is closed.

H I

Zone Control Outputs

Label: GREY- Common

VIOLET – Signal 0 – 10V

These terminals provide an alternate location for

connecting to the dimming ballast control circuit.

There can be up to three pairs of these

terminals depending on the model of miniZ

Power Pack. The dimming circuit provides the

analog output to control up to 100 dimming

ballasts. The basic version of the miniZ Power

Pack does not have any of these terminals.

Other manuals for miniZ mZb00-102

This manual suits for next models

Table of contents

Other Leviton Controllers manuals

Leviton

Leviton MC7008 User manual

Leviton

Leviton DRKDN-U Series User manual

Leviton

Leviton ILLUMATECH IPE04-1L User manual

Leviton

Leviton MLC128R User manual

Leviton

Leviton RTD01-10 User manual

Leviton

Leviton SGVSM-00W User manual

Leviton

Leviton intellect ZL057-D0Z User manual

Leviton

Leviton Decora NE515 User manual

Leviton

Leviton Decora Smart DW4BC User manual

Leviton

Leviton Acenti ACF01-1L User manual

Leviton

Leviton NorthStar Site Controller User manual

Leviton

Leviton Intellect ZLDNK User manual

Leviton

Leviton D4200 User manual

Leviton

Leviton Intellect ZL07S-N00 User manual

Leviton

Leviton NorthStar Site Controller User manual

Leviton

Leviton VZ00R-10 User manual

Leviton

Leviton Decora IPHS5 Series User manual

Leviton

Leviton DL057-D0Z User manual

Leviton

Leviton RZCZ1 User manual

Leviton

Leviton MS602-BW User manual

Leviton

Leviton CD250 User manual

Leviton

Leviton MLC128R User manual

Leviton

Leviton Decora Illumatech IPF01-1L User manual

Leviton

Leviton HXC10 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

Leviton miniZ mZb00-102 User manual

Popular Controllers manuals by other brands