Kwikset 44594/01 User manual

REMOVE LEVER AND COVER FROM LEVER ASSEMBLY

PREPARE LATCH AND INSTALL

If backset of door measured 2-3/4" (70mm), adjust latch as follows: Grasp the spring pin and

move it to the 2-3/4" slot.

Make sure that slant of latch bolt

faces in the direction that the door

closes.

OPTIONS

MEASURE

Keep handy for emergency unlocking.

2-3/8" (60mm)

2-3/4" (70mm)

Switch lever on exterior assembly as follows.

1. Insert wrench into set screw hole and loosen set screw.

2. Remove lever, replace with other lever and retighten set screw.

INSTALL EXTERIOR & INTERIOR ASSEMBLIES

Push latch to insert lever.

Snap on cover.

Tighten set screw to secure lever.

Install lever.

Continued

TRASH

FOR LEFT HAND DOORS - ONLY

IMPORTANT INSTALLATION INSTRUCTIONS

Required tools

LEVER - PRIVACY & PASSAGE

WITH 6-WAY LATCH

44594 / 01 CP

Connect assemblies by installing the mounting screws.

Push up on assembly until screws are level, before

fully tightening.

Do not use harsh chemicals or

solvents to clean your lock.

Mechanical lock

Use a damp cloth to wipe away

any excess dirt or debris.

Electronic lock

Use a damp cloth on the lock’s

exterior to wipe away any excess

dirt or debris. Use a dry cloth to

clean interior components.

FACE

• EDGE

DOOR DRILLING

4 5

2-3/8" 60mm

2-3/4" 70mm

2-1/4" (57mm)

1-3/4" (44mm)

1-3/8" (35mm)

Select desired backset

25mm

(25mm)

25 mm

(25mm)

2-3/8" (60mm)

2-3/4" (70mm)

BACKSET

Using a 2-1/8" (54mm) diameter hole saw, drill from one side until the point of drill

just breaks through, then complete hole from the other side to prevent splintering.

Drill hole 5/8" (16mm) deep.

Chisel out area until face plate sits flush and drill 3/32" (2mm)

diameter pilot holes for screws. Repeat for strike plate.

BACKSET

Centerline

FOLD OVER

•

TEMPLATE

Drill Hole in Door Face

Drill Hole in Door Edge

Mark Hole for Strike Plate Drill Strike Hole

Face and Strike Plate Cutouts

Mark Holes on Door

Privacy & Passage Lever

44594 / 01

38"

(965mm)

Extend mark across jamb to door stop. Locate center

of strike hole by measuring back from door stop,

1/2 the thickness of door.

25mm

3/32"

(2mm)

Required tools:

Align latch face plate on door edge and draw outline.

Repeat for strike plate on door jamb.

INSTALL STRIKE

Adjust tang as needed.

Rely on premium home doors & windows by Kwikset if you’re looking for quality and efficiency.

Table of contents

Other Kwikset Door Lock manuals

Kwikset

Kwikset SMARTCODE 9260CNT-514S User manual

Kwikset

Kwikset Powerbolt 2 Installation manual

Kwikset

Kwikset Smartcode 914 Operating instructions

Kwikset

Kwikset 62541/01 User manual

Kwikset

Kwikset Kevo User manual

Kwikset

Kwikset SMARTCODE 917 User manual

Kwikset

Kwikset Aura User manual

Kwikset

Kwikset 62873/01 User manual

Kwikset

Kwikset Prismo 740PSK RDT 15 SMT User manual

Kwikset

Kwikset Camino Pull User manual

Kwikset

Kwikset 907 15 SMT User manual

Kwikset

Kwikset 62883-002 User manual

Kwikset

Kwikset 553 User manual

Kwikset

Kwikset Smartcode 914 User manual

Kwikset

Kwikset Smartcode 910 User manual

Kwikset

Kwikset SmartCode 909 User manual

Kwikset

Kwikset Kevo User manual

Kwikset

Kwikset 914CZigBee C4 User manual

Kwikset

Kwikset Powerbolt 2 User manual

Kwikset

Kwikset 506KNL 3 User manual

Kwikset

Kwikset 62842/01 User manual

Kwikset

Kwikset 28756 User manual

Kwikset

Kwikset 62822/01 User manual

Kwikset

Kwikset 816 User manual

Popular Door Lock manuals by other brands

Assa Abloy

Assa Abloy effeff 827A-IP Mounting instructions

We.lock

We.lock SECBNEBL51 instructions

Iseo

Iseo MA1A installation guide

ID Lock

ID Lock 150 user manual

Lockly

Lockly ACCESS TOUCH PRO user manual

iLoq

iLoq G50S user guide

SDC

SDC Z7835 installation instructions

ilco

ilco 452 Installation

Samsung

Samsung shs-h705 user guide

TRU-BOLT

TRU-BOLT 08102017 user manual

CDVI

CDVI 500-LADJ quick start guide

Igloohome

Igloohome Deadbolt 2S Metal Grey Installer/user guide

eSSL

eSSL FL-300 user manual

JAKO

JAKO JKBTNX4 installation guide

Dorma

Dorma MUNDUS PREMIUM GK 50 Mounting instruction

SCOOP

SCOOP Pullbloc 4.1 FS Panik Assembly instruction

Yale

Yale MORTISE 8800 SERIES installation instructions

Siegenia

Siegenia KFV AS3500 Assembly instructions