Johnson Controls M9310-HGA-3 User manual
M9310 Series Electric Non-Spring Return Actuators Installation Guide
1
Applications
Installation
Parts included
• M9310 Series actuator
• anti-rotation bracket
• M3.5 x 9.5 mm long self-tapping crossed recessed
screw
Special tools needed
• torque wrench with 12 point 3/8 in. or 5/16 in.
open-end wrench
• 5/16 in. screwdriver
• digital voltmeter
Accessories
IMPORTANT: Use this M9310 Series Electric
Non-Spring Return Actuator only to control
equipment under normal operating conditions.
Where failure or malfunction of the electric actuator
could lead to personal injury or property damage to
the controlled equipment or other property,
additional precautions must be designed into the
control system. Incorporate and maintain other
devices, such as supervisory or alarm systems or
safety or limit controls, intended to warn of or protect
against failure or malfunction of the electric actuator.
Figure 1: M9310 actuator
FIG:M9310 Series Actuator
Table 1: Accessories (order separately)
Code number Description
M9000-321 Weathershield kit
M9300-1 Auxiliary switch kit (single-pole,
double-throw)
M9300-2 Auxiliary switch kit (two single-pole,
double-throw)
M9300-100 Threaded conduit adapters for
1/2 in. electrician’s fittings
M9300-140 Feedback potentiometer 140k
ohms
M9300-151 Remote mounting kit, with crank
arm and damper linkage
M9300-1K Feedback potentiometer 1k ohms
M9300-2K Feedback potentiometer 2k ohms
M9300-10K Feedback potentiometer 10k ohms
Figure 2: Anti-rotation bracket
FIG:Anti-rotatio n Bracket
Figure 3: Self-tapping screw
M9310 Series Electric Non-Spring Return Actuators
Installation Guide
M9310-HGA-3 Part No. 34-636-2456, Rev. D
Issued December 2022
M9310 Series Electric Non-Spring Return Actuators Installation Guide
2
Mounting
Adjusting the angular rotation stops
Mounting the actuator
1. Position the damper until it is fully closed. See
Table 2 for shaft diameters and required torques.
IMPORTANT: The M9310 Series actuator is not
rated for outdoor use. Do not mount the M9310
outdoors without the M9000-321 weathershield kit,
or it may fail to operate.
Figure 4: Mounting positions
FIG:Mounting Positions
Figure 5: Lifting the tab
FIG:Tab Location
Figure 6: Removing coupler
FIG:Romiving Coupler
Figure 7: Rotating coupler
FIG:Rotate Coupler
Figure 8: Installing coupler
FIG :Re ins tal ling Cou ple r
Figure 9: Mounting the actuator
FIG:Align Damper
M9310 Series Electric Non-Spring Return Actuators Installation Guide
3
2. Bend or cut the anti-rotation bracket to fit the
damper frame or duct.
3. Load the actuator seal by rotating the shaft using
the actuator (about 5 degrees).
4. Slip the actuator onto the shaft and fully tighten the
set screw on the coupler according to Table 2.
5. Lightly tighten one side of the anti-rotation bracket
to the mounting surface.
Figure 10: Forming the mounting bracket
M3.5 Screws (2)
Slot for Bracket
Anti-Rotation Bracket
Damper
Frame
Anti-Rotation
Bracket Tab
FIG:Underneath
Figure 11: Slipping the actuator onto the shaft
FIG:Tighten Actuator
Table 2: Shaft diameter and required torque
Shaft
diameter, in.
(mm)
With insert Without
insert
3/8
(9.5)
1/2
(12.7)
5/8
(16)
3/4 (19)
5/16
(8)
13/32
(10)
1/2
(12.7)
5/8 (16)
Required
torque, lb·in
(N·m)
125
(14.1)
Half-turn past hand-tighten
Figure 12: Attaching the bracket
F IG:Placin g B rac ket
M9310 Series Electric Non-Spring Return Actuators Installation Guide
4
6. Swing the anti-rotation bracket under the actuator
until it reaches the middle of the slot on the bottom
of the actuator.
7. Test the damper.
a. Press and hold the gear release.
b. Rotate the coupler fully closed to fully open to
verify that the damper and actuator rotate
freely throughout the range.
Figure 13: Securing the anti-rotation bracket to
the damper frame
FIG: Mount ed Actuator
Figure 14: Testing the damper
FIG:Pushbut ton
M9310 Series Electric Non-Spring Return Actuators Installation Guide
5
Wiring
M9310-HGA-3 actuators wiring diagrams
Risk of Electric Shock.
Disconnect the power supply before making electrical
connections. Contact with components carrying
hazardous voltage can cause electric shock and may
result in severe personal injury or death.
IMPORTANT: When using the M9310-HGA-3
actuator in floating mode, verify that the DIP switch
is positioned on the 2 to 10 VDC option. This setting
ensures compatibility with the controller’s triac
output exhibiting voltage leakage. See Figure 20 for
DIP switch placement.
Figure 15: Floating 24 V applications
RED
GRY
BLK
ORN
COM
0 t o 10 VDC
(-)
24 V AC/DC
(+)
FIG:Floating 24V Applications
Figure 16: On/off 24 V applications (See Table 3
for dip switch placement)
RED
GRY
BLK
ORN
24 V AC/DC
24 V AC/DC
COM
0 to 10 VDC
(-)
(+)
FIG:On/Of f 24V Applicatio ns
Figure 17: Proportional 24 V applications
RED
GRY
BLK
ORN
24 V AC/DC
0 to 10 VDC
COM
0 to 10 VDC
(-)
(+)
(+)
(-)
FIG:Proportional 24V Applications
Figure 18: Proportional 24 V applications - 0 (4)
to 20 mA with external resistor
M9310 Series Electric Non-Spring Return Actuators Installation Guide
6
Auto calibration mode
The actuator enters auto calibration mode and
positions the coupler to the maximum and minimum
end stops to identify the range of travel.
Accessing the dip switches and LEDs
Locate the oval cover on the front of the unit and pull
the cover outward.
To complete the auto calibration process, press
Enter/Autocal until all three LEDs are on. See
Figure 20 for viewing the DIP switches and LEDs.
Operation
The valid Offset values are 0 to 10 VDC and the valid
Span values are 2 to 10 VDC. The maximum feedback
voltage of the actuator is 10 VDC.
Figure 19: DIP switch and LED cover
FIG:LED and DIP Switch Cover
Risk of Property Damage.
Do not apply power to the system before checking all
wiring connections. Short circuited or improperly
connected wires may result in permanent damage to
the equipment.
Figure 20: DIP switches and LEDs placement
Figure 21: Graphed examples of Table 3
command signals
Max.
10 VDC
FIG:Example Graph
Min.
20 VDC0 VDC
Stroke
M9310 Series Electric Non-Spring Return Actuators Installation Guide
7
Setting the SPAN and OFFSET proportional
command signal to other values
1. Set DIP switch one and two before proceeding.
Refer to Figure 20 for DIP switch placement.
2. Connect a digital multimeter between the orange
(feedback) and black (common) wires. See Wiring
for more wiring information.
3. Press Enter/Autocal.
To adjust the span and offset, press but not hold
Enter/Autocal. Holding Enter/Autocal for longer
than three seconds triggers an autocal.
The Offset Adj. LED turns on, and the multimeter
displays the current offset value.
4. Press INC.
The Offset Adj. LED flashes. The voltage reading
on the multimeter increases 0.5 VDC each time
you press the button. Press INC. until you reach
the desired voltage.
If no further action is required, the Offset Adj. LED
stops flashing after 10 seconds. The actuator exits
the program mode and the original offset value
remains unchanged.
5. Press Enter/Autocal.
The Offset Adj. LED turns off indicating that the
desired Offset Adj. value was recorded. The Span
Adj. turns on, and the multimeter displays the
present SPAN value.
6. Press INC.
The Span Adj. LED flashes. The voltage reading on
the multimeter increases by 0.5 VDC each time
you press the button. Press INC. until you reach
the desired voltage.
If no further action is required, the Offset and Adj.
LED stops flashing after 10 seconds. The actuator
exits the program mode and the original offset
value remains unchanged.
7. Press Enter/Autocal.
The Span Adj. LED turns off indicating that the
desired Span Adj. setting is saved, and the
actuator exits the program mode.
Reading the SPAN and OFFSET proportional
command signal voltage settings
1. Connect a digital multimeter between the orange
(feedback) and black (common) wires. See Wiring
for more wiring information.
2. Press Enter/Autocal.
The Offset Adj. LED turns on, and the multimeter
displays the current offset value.
3. Press Enter/Autocal.
The Offset Adj. LED turns off, the Span Adj. LED
turns on, and the multimeter displays the present
SPAN value.
4. Press Enter/Autocal.
The Span Adj. LED turns off.
Table 3: DIp switch settings
Example Command
signal
Feedback
signal
Settings M9310-HGA
user interface
10 to 10
VDC
Direct
0 to 10
VDC
20 to 10
VDC
Reverse
0 to 10
VDC
32 to 10
VDC
Direct
2 to 10
VDC
24 VAC –
4Offset = 5
Span = 7
Reverse
2 to 10
VDC
Risk of Electric Shock.
Do not touch any exposed metal parts with anything
other than properly insulated tools or insulated probes
of the digital voltage meter. Failure to use properly
insulated tools and probes may result in severe
personal injury or death.
DA 0-10
RA 2-10
DA 0-10
RA 2-10
DA 0-10
RA 2-10
DA 0-10
RA 2-10
IMPORTANT: Do not press INC. Otherwise your
observed offset voltage setting will change.
IMPORTANT: Do not press INC. Otherwise your
observed SPAN voltage setting will change.
M9310 Series Electric Non-Spring Return Actuators Installation Guide
8
Clearing the SPAN and OFFSET proportional
command signal voltage setting
Cycle DIP switch two between 2 to 10 and 0 to 10. The
active setting is the final state of DIP switch two.
Installing the cover over the dip switches and
LEDs
Repositioning the actuator hub
Removing the conduit connector
You can remove the conduit connector at the bottom of
the unit if the connector is damaged. To remove the
connector:
1. Insert a screwdriver into the slot on the housing.
2. Rotate the conduit connector counterclockwise and
remove it from the actuator.
Repair information
If the M9310 Series Electric Non-Spring Return
Actuators fail to operate within its specifications,
replace the unit. For a replacement actuator, contact
the nearest Johnson Controls® representative.
IMPORTANT: Once you have verified the DIP
switch placement and LED activity, place the oval
cover back onto the unit before repositioning the
actuator hub.
IMPORTANT: The manual override is automatically
released when the button is released.
Do not rotate the manual override shaft faster than 3
seconds for each rotation. Rotating the manual
override shaft faster than the recommended speed
may result in permanent damage to the actuator.
Figure 22: Repositioning the actuator hub
Figure 23: Removing the conduit connector
FIG:Conduit Connector
Callout Description
1Manual override button
2Set-screw
3Shaft linkage
M9310 Series Electric Non-Spring Return Actuators Installation Guide
9
Technical specifications
M9310 Series Electric Non-Spring Return Actuator
Product description M9310-HGA-3: On/Off and floating mode M9310-HGA-3: Proportional mode
Power requirements 24 VAC (19.2 to 28.8 VAC) at 50/60, Class 2 (North America) or SELV (Europe), 6 VA
running. 24 VDC (21.6 to 28.8 VDC) Class 2 (North America) or SELV (Europe)
Transformer sizing
requirements
<6 VA
Input signal/adjustments 19.2 to 28.8 VAC at 50/60 Hz or 24 VDC
±10 Class 2 (North America) or SELV
(Europe)
0 (2) to 10 VDC or 0 (4) to 20 mA with field
furnished 500 ohm 1/4 W resistor
Offset: 0 to 10 VDC
SPAN: 2 to 10 VDC
Control impedance 4.7k ohm 100k ohm
Feedback signal – 0 (2) to 10 VDC
Running torque 88 lb·in (10 N·m)
Rotation range Mechanically limited 35to95±3in 5 increments
Rotation time 90 seconds
Rotation time autocalibration 35 seconds
Cycles 100,000 full stroke cycles; 2,500,000 repositions
Audible noise <35 dBA at 39-13/32 in. (1 m)
Electrical connections 48 in. (1.2 m) Halogen free cable with 18 AWG cable (0.82 mm²) conductors and 0.25 in.
(6 mm) ferrule ends
Conduit connections 1/2 in. NPSM (13 mm) threaded conduit connectors with M9300-100 conduit connector
Mechanical connections Round 3/8 in. to 3/4 in. (centered on 1/2 in.)
Square 3/8 in. to 5/8 in.
Ambient conditions Operating: -22 to 140F (-30 to 60C), 90% RH, noncondensing
Storage: -40 to 185F (-40 to 85C), 95% RH, noncondensing
Enclosure IP54/NEMA 5
Dimensions 3-3/16 in. (81 mm) wide x 2-1/2 in. (63 mm) high x 5-5/8 in. (143 mm) long
Shipping weight 2 lb (0.9 kg)
Compliance United States:
UL Listed, CCN XAPX, File E27734; to UL 60730-1: Automatic Electrical Controls for
Household and Similar Use, Part 1; and UL 60730-2-14: Part 2, Particular Requirements
for Electric Actuators. Plenum Rated (UL 2043). Suitable for use in Other Environmental
Air Space (Plenum) in accordance with section 300.22 (c) of the National Electrical Code.
Canada:
UL Listed, CCN XAPX7, File E27734; to CAN/CSA E60730-1:02: Automatic Electrical
Controls for Household and Similar Use, Part 1; and CAN/CSA-E60730-2-14, Particular
Requirements for Electric Actuators.
United States:
UL Listed, CCN XAPX, File E27734; to UL 60730-1: Automatic Electrical Controls for
Household and Similar Use, Part 1; and UL 60730-2-14: Part 2, Particular Requirements
for Electric Actuators. Plenum Rated (UL 2043). Suitable for use in Other Environmental
Air Space (Plenum) in accordance with section 300.22 (c) of the National Electrical Code.
Canada:
UL Listed, CCN XAPX7, File E27734; to CAN/CSA E60730-1:02: Automatic Electrical
Controls for Household and Similar Use, Part 1; and CAN/CSA-E60730-2-14, Particular
Requirements for Electric Actuators.
Australia and New Zealand: RCM, Australia/NZ Emissions Compliant
The performance specifications are nominal and conform to acceptable industry standard. For application at conditions beyond these specifica-
tions, consult the local Johnson Controls office. Johnson Controls shall not be liable for damages resulting from misapplication or misuse of its
products.
www.johnsoncontrols.com
M9310 Series Electric Non-Spring Return Actuators Installation Guide
10
Single point of contact
UK Single Point of Contact: European Single Point of Contact: NA/SA Single Point of Contact: APAC Single Point of Contact:
JOHNSON CONTROLS
TYCO PARK GRIMSHAW LANE
MANCHESTER M40 2WL
UNITED KINGDOM
JOHNSON CONTROLS
VOLTAWEG 20
6101 XK ECHT
THE NETHERLANDS
JOHNSON CONTROLS
5757 N GREEN BAY AVE
GLENDALE WI 53209
USA
JOHNSON CONTROLS
C/O CONTROLS PRODUCT MANAGEMENT
NO. 32 CHANGJIANG NEW DISTRICT
WUXI JIANGSU PROVINCE 214028
CHINA
Johnson Controls® is registered trademark of Johnson Controls.
All other marks herein are the marks of their respective owners.
© Copyright 2022 Johnson Controls. All rights reserved. Any unauthorized use or copying is strictly prohibited.
Building Technologies & Solutions
Headquarters: Milwaukee, Wisconsin, USA
Branch offices: Principal cities worldwide
Contact information
Contact your local branch office: www.johnsoncontrols.com/locations
Contact Johnson Controls: www.johnsoncontrols.com/contact-us
Product warranty
This product is covered by a limited warranty, details of which can be found at www.johnsoncontrols.com/buildingswarranty.
Patents
Patents: http://jcipat.com
This manual suits for next models
1
Table of contents
Other Johnson Controls Controllers manuals
Johnson Controls
Johnson Controls M9102-AGA-2S Series User manual
Johnson Controls
Johnson Controls VA-8122 Service manual
Johnson Controls
Johnson Controls UZC-256 User manual
Johnson Controls
Johnson Controls Facility Explorer FX40 User manual
Johnson Controls
Johnson Controls M9108-A-1N Series User manual
Johnson Controls
Johnson Controls TEC3620 Series User manual
Johnson Controls
Johnson Controls FAC3613 User manual
Johnson Controls
Johnson Controls M9116-GG-1N4 Series User manual
Johnson Controls
Johnson Controls M9316-A Z Series User manual
Johnson Controls
Johnson Controls VA-9070 Series User manual
Johnson Controls
Johnson Controls TEC3310 User manual
Johnson Controls
Johnson Controls FEC26 Series User manual
Johnson Controls
Johnson Controls M4-CGM Series User manual
Johnson Controls
Johnson Controls VMA1615 User manual
Johnson Controls
Johnson Controls F4-DLK0350 User manual
Johnson Controls
Johnson Controls FEC26 Series User manual
Johnson Controls
Johnson Controls P2000 Manual
Johnson Controls
Johnson Controls FX-PCA3611 User manual
Johnson Controls
Johnson Controls EasyIO FW-08 V3 User manual
Johnson Controls
Johnson Controls tyco Kantech IP LINK User manual
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
