Johnson Controls EDA-8100 Assembly instructions

Installation Sheet

Issue Date 0392

1. EDA-8100-1100 Electric Damper Actuator with counterclockwise

spring return, or

EDA-8100-1101 Electric Damper Actuator with clockwise spring

return

2. Two #10 mounting screws

3. Two isolator grommets

ςscrewdriver, flat blade, 1/4 to 5/16 inch and 1/8 inch tips

ςdrill, 5/32 inch (4 mm) drill bit, 1-1/4 inch hole saw

ςadjustable wrench

ςpliers

Figure 1: Electric Damper Actuator

1. Compatibility and torque:

ςuse on dampers having 10 to 12 mm (0.394 to 0.492 inch) square

or 7/16 to 1/2 inch (11 to 12.5 mm) round shafts

ςcompatible with Johnson Controls D-1300 Blade Dampers

ςdelivers 100 in·lb of stall torque

2. Mounting requirements:

ςmounts in any orientation

ςduct or wall must be 16 gauge (0.06 inch or 1.5 mm) or thicker

Note: Order the Universal Mounting Bracket (D-3153-105) to mount on

duct or wall less than 16 gauge.

EDA-8100 Electric Damper Actuator

Kit Includes

Tools Required

Installation

Overview

EDA-8100 Electric Damper Actuator

1. Follow NEC and local electrical codes.

2. Disconnect all power supplies.

3. Observe ranges and limitations for individual model.

4. Do not install the actuator in applications where its failure could result

in personal injury and/or loss of property.

5. Do not install if explosive vapors, corrosive vapors, or escaping gases

will be present.

6. Add protective control devices as needed to prevent undesirable

system failure modes.

For#10 Mounting

Screw(6places)

2.33

(59)

2x1.50

2x0.75

6.94

(235)

8.78

(223)

9.26

(235)

4.65

(118)

Figure 2: Top View Dimension inches

Mounting Caution

Pre-Mounting

EDA-8100 Electric Damper Actuator 3

4.34

(110)

6 in. min*

(3x 0.875)

for 1/2 in. conduit

Rubber Grommet

(2 Required)

* Six inch minimum required for cover removal, field wiring, and field adjustments.

Figure 3: End View Dimension inches

Note: Before starting the job, obtain the damper installation information

to use as a reference when mounting the actuator.

1. Locate the preferred driving blade on the damper.

2. Cut a 1-1/4 inch (32 mm) hole in the duct or wall over the driving

blade pin.

3. Attach the drive pin extension to the drive pin and secure using the

clip provided.

4. Firmly grasp the drive pin extension with a pliers and manually close

the damper blades.

RetainerClip

Drive PinExtension

Figure 4: Rotation

5. Note which direction closes the damper, clockwise (CW) or

counterclockwise (CCW).

EDA-8100 Electric Damper Actuator

Figure 5: Removing Cover

6. Insert a screwdriver under the edge of the plastic cover to gently pry

off the cover. See Figure 5.

7. Verify the mode of operation for the proper model number from

Table 1.

Table 1: Operation Modes

Product Code

No. Drive

Type Travel

Time Spring

Return

EDA-8100-1100 incremental 180 second counterclockwise

EDA-8100-1101 incremental 180 second clockwise

Note: The actuator can be mounted in any orientation.

1. Position the actuator onto the drive pin extension so that the actuator

sits against the duct.

2. Use of the actuator’s center mounting slots with the isolation

grommets is the preferred mounting arrangement. If the duct or wall

is less than 16 gauge (0.06 inch or 1.5 mm), order and use the

Universal Mounting Bracket (D-3153-105).

Note: Because of eccentric motion of the actuator that occurs when using

shafts smaller than 10 mm (0.394 inch) square or 1/2 inch

(12.5 mm) round, use of the isolation grommets in the center

mounting slot is required.

3. Mark the location of the actuator's top and bottom mounting slots on

the duct or wall.

4. Remove the actuator and set aside.

5. Drill 5/32 inch (4 mm) holes in the duct or wall at the marked

locations.

Mounting

EDA-8100 Electric Damper Actuator 5

6. Slide the actuator onto the drive pin extension.

7. Secure the actuator to the wall or duct with the screws and isolation

grommets included in the kit.

8. Tighten the two square-head screws on the actuator coupler.

Note: The cover should remain off until the wiring is completed.

CAUTION: Disconnect all power before wiring the actuator to

avoid electrical shock or damaging the equipment.

Opening Covers

ConduitOpening

Figure 6: Conduit Openings

1. Insert the leads from the controller through one of the three openings.

2. Install the black plugs in the other two conduit openings. See

Figure 6.

Wiring

EDA-8100 Electric Damper Actuator

24 VAC Input Power

Clockwise 24 VAC

Control Signal

Counterclockwise

24 VAC Control Signal

Common

COMCCW CW PWR

FT1

FT2

FT4

FT3

FT6

FT5

FT7

Figure 7: Wiring Connections

3. Connect the leads to Terminal Block 1 (TB1) as shown in Figure 7.

1. Apply power.

2. Use the checkout procedure described in the controller instructions to

check the action of the actuator.

3. Run the actuator fully CW and CCW.

4. Verify that the damper blades fully open and close.

5. Install the plastic cover.

Checkout

Procedure

EDA-8100 Electric Damper Actuator 7

The EDA-8100 is not field repairable. For a replacement, contact the

nearest Johnson Controls branch office or your wholesale distributor.

Replacement

EDA-8100 Electric Damper Actuator

Notes

Controls Group

507 E. Michigan Street

P.O. Box 423

Milwaukee, WI 53201

Table of contents

Other Johnson Controls Controllers manuals

Johnson Controls

Johnson Controls FX-PCV1617 User manual

Johnson Controls

Johnson Controls TEC3010 User manual

Johnson Controls

Johnson Controls VA9208-AG Series User manual

Johnson Controls

Johnson Controls G76 Series User manual

Johnson Controls

Johnson Controls M9132-AG -1N Series User manual

Johnson Controls

Johnson Controls VMA1615 User manual

Johnson Controls

Johnson Controls VMA1615 User manual

Johnson Controls

Johnson Controls DS-3153 User manual

Johnson Controls

Johnson Controls MP8 20 Series User manual

Johnson Controls

Johnson Controls P77 Series User manual

Johnson Controls

Johnson Controls FMS-2000C User manual

Johnson Controls

Johnson Controls M9108-GG 1N Series User manual

Johnson Controls

Johnson Controls CK721-A Assembly instructions

Johnson Controls

Johnson Controls LX Series User manual

Johnson Controls

Johnson Controls TRUE RH HC-67x3 User manual

Johnson Controls

Johnson Controls FEC1611 User manual

Johnson Controls

Johnson Controls FEC25 User manual

Johnson Controls

Johnson Controls F4-CG Series User manual

Johnson Controls

Johnson Controls M9203-AG-2 Series User manual

Johnson Controls

Johnson Controls FX Supervisory Controller RS-485 Card User manual

Johnson Controls

Johnson Controls TEC2664Z-3 BACnet User manual

Johnson Controls

Johnson Controls F4-CVM User manual

Johnson Controls

Johnson Controls FA-33-741 Series User manual

Johnson Controls

Johnson Controls TEC3310 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual