ICP DAS USA 7188EN Installation guide

分類/Classification

tDS

tGW

PETL/tET/tPET

DS/PDS/PPDS

tM-752N

I/O Card

VXC Card

VxComm

7188EN

作者/Author

Tammy

日期/Date

2016-01-12

編號/NO.

FAQ-043

Q: How to enable web server for the PDS/7188EN series module?

A: The PDS/7188EN series module contains a built-in web server that allows the settings for the module to

be remotely modified via a web interface. When the web server has been disabled (Web Server = 0), refer

to the following two methods to enable the web server.

Method 1: Enable web server on PDS by using “console port and command”.Follow the procedure

described below:

1. Power off the PDS module.

2. Connect the download-cable (CA0910), between the PDS and COM4 of the development PC.

3. Wire the CA-0910 to PDS, as follows:

Connect the CA-0910.TX with PDS.TxD

Connect the CA-0910.RX with PDS.RxD

Connect the CA-0910.GND with PDS.GND

4. Set the “Init/Normal Switch”on the PDS module to the in “Init”position.

(Or connect the INIT* pin to the GND pin.)

5. Power on the PDS module.

6. Unzip the “7188XW_yyyymmdd.zip” file on the PC. The “7188XW_yyyymmdd.zip”can be obtained

from the ICP DAS web site (http://ftp.icpdas.com/pub/cd/8000cd/napdos/minios7/utility/).

7. Open “Notepad”text editor for Windows and type the command: C4 B115200 P0D8 S1, and then save

the file as “7188xw.ini”in the same directory of 7188XW.exe.

8. Execute “7188XW.EXE”and press [Enter] key.

9. Settings configuration command:

The following is an example of a HTTP configuration.

Command

Description

HTTP= 1

Enables the Web Server.

HTTP= 0

Disables the Web Server.

Enable Web Server

C: COM Port of the development PC (e.g., C4)

B: Baud Rate (e.g., B115200)

P: Parity None (e.g., P0)

D: Data Bits (e.g., D8)

S: Stop Bits (e.g., S1)

Method 2: Enable web server on PDS by using “TCP port 10000”.Follow the procedure described below:

1. Ensure that the network settings on the Host PC have been correctly configured and are functioning

normally. Connect both the PDS module and the Host PC to the same sub network or the same

Ethernet Switch, and apply power to the PDS module.

2. Configure the correct network settings for the required PDS module. Refer to PDS Quick Start Guide for

more detailed information.

(http://ftp.icpdas.com/pub/cd/8000cd/napdos/pds/pds-700/document/quick_start/)

3. Download the “Terminal.exe”on your PC, or use other telnet client program. The “Terminal.exe”can

be downloaded from the ICP DAS web site.

(http://ftp.icpdas.com/pub/cd/tinymodules/napdos/software/)

4. Double click the “Terminal.exe”to open “Configuration Settings”dialog box.

5. Click the “TCP/IP Port”tab to configure the parameters as follows:

5-1: Type the “IP address of the PDS module”in the “IP Address”field.

5-2: Type the “10000”in the “TCP/IP Port”field.

5-3: Click the “Open COM”button.



6. Select the “Hex/Text”option in the “Display”filed and settings configuration command:

Command

Description

26SAVE=1, HTTP=1

Enables the Web Server and save the configuration to EEPROM.

26SAVE=1, HTTP=0

Disables the Web Server and save the configuration to EEPROM.

7. Type the “26SAVE=1, HTTP=1”string in the “send”field then click the “Send”button.

8. If the response is received, it will be displayed in the received field that means the success.

9. Reboot the PDS module to complete the configuration.







This manual suits for next models

Table of contents

Other ICP DAS USA Control Unit manuals

ICP DAS USA

ICP DAS USA I-7016 User manual

ICP DAS USA

ICP DAS USA I-8088W User manual

ICP DAS USA

ICP DAS USA PET-7261 User manual

ICP DAS USA

ICP DAS USA ZT-2570 User manual

ICP DAS USA

ICP DAS USA ECAT-201x EtherCAT Slave I/O User manual

ICP DAS USA

ICP DAS USA PISO-CPM100U-D/T User manual

ICP DAS USA

ICP DAS USA I-7041 User manual

ICP DAS USA

ICP DAS USA DS-2200 Series User manual

ICP DAS USA

ICP DAS USA ZT-2017 User manual

ICP DAS USA

ICP DAS USA EIP-2060 User manual

ICP DAS USA

ICP DAS USA M-7017R User manual

ICP DAS USA

ICP DAS USA PDS-220F Series Use and care manual

ICP DAS USA

ICP DAS USA SG-3784M User manual

ICP DAS USA

ICP DAS USA tET Series User manual

ICP DAS USA

ICP DAS USA I-7083 User manual

ICP DAS USA

ICP DAS USA I-7083 User manual

ICP DAS USA

ICP DAS USA SG-785 User manual

ICP DAS USA

ICP DAS USA GW-7552-M User manual

ICP DAS USA

ICP DAS USA ET-6000 Series User manual

ICP DAS USA

ICP DAS USA GTP-230 User manual

ICP DAS USA

ICP DAS USA tZT-P4C4 User manual

ICP DAS USA

ICP DAS USA tM-AD5 User manual

ICP DAS USA

ICP DAS USA PET-7053 User manual

ICP DAS USA

ICP DAS USA I-7063 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual