ICP DAS USA I-7041 User manual

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

I-7041

14 Channel Isolated Digital Input Data

Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/i_7041

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The I-7041 provides 14 channels for digital input, each of which features

photo couple isolation. In addition, sink- or source-type digital input can be

selected via wire connections, and all channels are able to be used as 16-

bit counters. 4 kV ESD protection and 3750 VDC intra-module isolation are

standard. ICPDAS recommends selecting the "P" version of the digital input

module for industrial use.

2. Terminal Assignment

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Default Settings

Default settings for the I-7043 DIO modules are as follows:

。Module Address: 01

。DIO Type: Type 40

。Baud Rate: 9600 bps

。Checksum disabled

。J3 set to INIT mode enabled for I-7043/43D a

5. Configuration

To install the module, follow the steps below:

1. Connect the analog output.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. For I-7000 modules, DCON utility pro terminal can send command to the module.

See user manual Sections 2 for details command.

Configure the module: sending the %AANNTTCCFF command. See user manual

Section 2 for details.

Read data from the input channels: send either the #AA or #AAN command to the

module.

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Table of contents

Other ICP DAS USA Control Unit manuals

ICP DAS USA

ICP DAS USA I-7060D User manual

ICP DAS USA

ICP DAS USA M-7019Z User manual

ICP DAS USA

ICP DAS USA WP-5231 User manual

ICP DAS USA

ICP DAS USA M-7069 User manual

ICP DAS USA

ICP DAS USA I-87004W User manual

ICP DAS USA

ICP DAS USA I-7063D User manual

ICP DAS USA

ICP DAS USA GTP-230 User manual

ICP DAS USA

ICP DAS USA ET-7218Z User manual

ICP DAS USA

ICP DAS USA Zigbee ZT-2060 User manual

ICP DAS USA

ICP DAS USA M-7067 User manual

ICP DAS USA

ICP DAS USA tPET-P6 User manual

ICP DAS USA

ICP DAS USA ECAT-2016N User manual

ICP DAS USA

ICP DAS USA tSH-725 User manual

ICP DAS USA

ICP DAS USA GW-7552-M User manual

ICP DAS USA

ICP DAS USA ZT-2017 User manual

ICP DAS USA

ICP DAS USA ET-2200 Series User manual

ICP DAS USA

ICP DAS USA tET-P6 User manual

ICP DAS USA

ICP DAS USA DS-2200 Series User manual

ICP DAS USA

ICP DAS USA tSH-734 User manual

ICP DAS USA

ICP DAS USA tM-AD8C User manual

ICP DAS USA

ICP DAS USA M-7033D User manual

ICP DAS USA

ICP DAS USA I-7063 User manual

ICP DAS USA

ICP DAS USA ECAT-2012H User manual

ICP DAS USA

ICP DAS USA MDC-700 Series User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual