ICP DAS USA I-7083 User manual

I-7083 3-axis, 32-bit Encoder Counter DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

1

I-7083

3-axis, 32-bit Encoder Counter Data

Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/i_7083

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The I-7083 and I-7083B are 3-axis high speed encoder modules. Each axis on the module can be

independently confi gured as one of Quadrant, Pulse/Dir or CW/CCW input mode with a

maximum input rate of 1 MHz. The high-end specifications of the I-7083/I-7083B and complete

software support make it ideal for a wide range of applications in position measurement of

motion systems working in industrial and laboratory environments. The I-7083B is an improved

version of I-7083 with virtual battery backup function for counter value.

2. Terminal Assignment

I-7083 3-axis, 32-bit Encoder Counter DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

2

3. Block/ Wiring Diagram

4. Default Settings

Default settings for the I-7083 module is as follows:

- address=01

- baud rate=9600

- checksum disable

- data=1 start+8 data+1 stop(no parity)

- type=53

- Mode= 5 for 7083, L=0, XOR=1, CwCcw mode

D for 7083B, L=1, XOR=1, CwCcw mode

I-7083 3-axis, 32-bit Encoder Counter DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3

5. Configuration

To install the module, follow the steps below:

1. Connect the analog output.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

I-7083 3-axis, 32-bit Encoder Counter DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

I-7083 3-axis, 32-bit Encoder Counter DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5

7. For I-7000 modules, DCON utility pro terminal can send command to the module.

See user manual Sections 2 for details command.

Configure the module: sending the %AANNTTCCFF command. See user manual

Section 2 for details.

Read data from the input channels: send either the #AA or #AAN command to the

module.

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Other manuals for I-7083

1

This manual suits for next models

1

Table of contents

Other ICP DAS USA Control Unit manuals

ICP DAS USA

ICP DAS USA SG-3784M User manual

ICP DAS USA

ICP DAS USA EIP-2000 Series Installation guide

ICP DAS USA

ICP DAS USA M-7064 User manual

ICP DAS USA

ICP DAS USA I-7045 User manual

ICP DAS USA

ICP DAS USA I-8014W User manual

ICP DAS USA

ICP DAS USA ECAT-201x EtherCAT Slave I/O User manual

ICP DAS USA

ICP DAS USA M-7051D User manual

ICP DAS USA

ICP DAS USA M-7019Z User manual

ICP DAS USA

ICP DAS USA WF-2026 User manual

ICP DAS USA

ICP DAS USA CAN-8123 User manual

ICP DAS USA

ICP DAS USA iDaSer-9000 User manual

ICP DAS USA

ICP DAS USA ZT-2570 User manual

ICP DAS USA

ICP DAS USA IR-310-RM User manual

ICP DAS USA

ICP DAS USA SG-3227 User manual

ICP DAS USA

ICP DAS USA GW-7552-M User manual

ICP DAS USA

ICP DAS USA I-8124W User manual

ICP DAS USA

ICP DAS USA DS-2200 Series User manual

ICP DAS USA

ICP DAS USA ECAT-2012H User manual

ICP DAS USA

ICP DAS USA SG-3016 User manual

ICP DAS USA

ICP DAS USA GTM-204M-4G User manual

ICP DAS USA

ICP DAS USA I-8213W-4G User manual

ICP DAS USA

ICP DAS USA tGW-700 Series User manual

ICP DAS USA

ICP DAS USA SG-3071 User manual

ICP DAS USA

ICP DAS USA M-7033D User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual