IBM 3746 User manual

IBML Installation Instructions

Field Feature Bill of Material

PN 25L9934

64 Mb Memory Upgrade (FC 3520)

on the System Card of the Multiaccess Enclosure (FC 3000)

of the IBM 3746 Models 9X0

Written by: C. Vallee

Checked by: J. Dauverd

Approved by: A. Badino

Reviewed by: B. Kelly

3746 PN 25L9934 EC F12604

FFBM 1 of 10 14/04/1998

Copyright IBM Corp. 1998 1

IBML Installation Instructions

3746 PN 25L9934 EC F12604

FFBM 2 of 10 14/04/1998

IBML Installation Instructions

Before Installation (Steps 1-8)

1.0 Machines Affected

3746 Model 9X0 with Multiaccess Enclosure (FC 3000) and MAE Extended Func-

tions (FC 5804).

This feature should only be applied on the machine serial for which it is speci-

fied

2.0 Related BMs and ECs

2.1 Prerequisites

(Must be installed prior to this installation)

Feat

B/M Title

86H0250 Multiaccess Enclosure (FC 3000) at EC E49252 or higher.

and

EC Title

F12380 Licensed Internal Code (Minimum level)

Checkpoint: Check that the CSS 1 EC Level is F12380.000 or higher.

Note: Refer to

SPIM

, Chapter 3.

Displaying the EC Level of the Code.

2.2 Concurrent ECs

(Must be installed together)

None.

2.3 Companion ECs

(May be installed together)

None.

3.0 BMs to be Installed

FB/M Title

25L9934 System Card Memory Upgrade 64 Mb.

3746 PN 25L9934 EC F12604

FFBM 3 of 10 14/04/1998 3

IBML Installation Instructions

4.0 Preparation

•Familiarize yourself with the purpose and details of the installation instruc-

tion before negotiating machine time with the customer.

•Check all items listed on the BM(s) to determine that all parts have been

received.

5.0 Programming

None.

6.0 Purpose and Description

To increase the performance by adding a 64 Mb Dual Inline Memory Module

(DIMM) on the system card on the Multiaccess Enclosure.

7.0 Installation Time

FFBM Machine

Hrs. System Hrs. CE Hour Nbr of CE

25L9934 00.0 00.0 1 1

8.0 Tools/Material Required

None.

3746 PN 25L9934 EC F12604

FFBM 4 of 10 14/04/1998

IBML Installation Instructions

Installation (Steps 9-12)

9.0 Safety

Review the Safety Notices and the Safety Inspection Procedures located at the

beginning of the

IBM 3745 Communication Controller All Models

IBM 3746

Expansion Unit Model 900

IBM 3746 Nways Multiprotocol Controller Model 950

Safety Information

, GA33-0400.

10.0 Details of Installation

Attention.

The System Card is not hot pluggable.

Electrostatic discharge (ESD) can damage the static-sensitive devices on circuit boards. To avoid

this kind of damage, use the following precautions:

•Do not remove the DIMM until you are ready to insert it into the Multiaccess Enclosure.

•Use correct grounding techniques when inspecting and installing the DIMM. Use a foot strap or

grounding mat, or wear a grounded static discharge wrist strap, or touch a grounded rack or

other source of ground before you handle the DIMM.

10.1 Removing the System Card

1. Switch OFF each power supply.

2. Unplug the cables from the system card.

3. Loosen thumbscrews on the system card.

4. Remove the system card and lay it on a

soft non-conductive surface.

3746 PN 25L9934 EC F12604

FFBM 5 of 10 14/04/1998 5

IBML Installation Instructions

10.2 Adding a DIMM on the System Card

1. Remove the DIMM, in its antistatic bag, from its shipping container.

2. Remove the DIMM from the antistatic bag. Inspect it for damage.

Always handle the DIMM by the ends (preferably grasp it between the

middle finger and thumb; do not touch the components). If the DIMM

appears to be damaged, return it to the antistatic bag and contact the

supplier.

3. On the System card, Locate the DIMM sockets (Slots U87 and U86 -

Refer to figure below).

Note: Any slot can be used to install the first DIMM.

4. Insert the DIMM into the free slot. (Grasping the DIMM between the

middle finger and thumb, place it connector edge down into the DIMM

socket. Applying slight pressure to the top edge of the DIMM, move it

forward until it is correctly aligned and snaps in place.)

The lever will snap back into place as the DIMM is fully inserted.

10.3 Re-installing the System Card

1. Re-install the new system card. Make sure the card is aligned with the

plastic grooves and then slide it in until it is flush with the box. Hold the

locking latches so that they are perpendicular to the face of the system

card. With the card in full contact with the rear of the Multiaccess Enclo-

sure, press the locking latches into the system card.

2. Tighten the thumbscrews on the face of the adapter card clockwise.

3746 PN 25L9934 EC F12604

FFBM 6 of 10 14/04/1998

IBML Installation Instructions

3. re-plug the cables into the system card.

4. Power ON; Then verify the LEDs (Refer to Figure 1 and to page 8 for

LEDs status meaning).

Figure 1. Power Supply, System Card, and Adapter Card LEDs

3746 PN 25L9934 EC F12604

FFBM 7 of 10 14/04/1998 7

IBML Installation Instructions

Power Supply Status

System Card Status

Adapter Card Status

LEDs Meaning

Yellow

(Overcurrent) On - There is an overcurrent condition with the −48 V to one or

more of the adapters (slots 1−8) or the +12 V to the fan tray.

Green DC On - +5 V, +12 V, and −48 V are OK.

Green AC On - AC source voltage is present and within tolerance.

LEDs Meaning

PCMCIA 1 or

PCMCIA 2

(Yellow)

On - PCMCIA device has a fault, is not installed, or is not seated

correctly.

Off - Device passed self-tests

OK (Green) On - Card hardware is operating normally.

Blinking - Loading from hard file

OK (Yellow) On - Card hardware has a fault.

Fault Hard Drive

(Yellow) On - Hard drive has failed.

LEDs Meaning

OK (Green) On - Adapter is operating normally.

OK (Yellow) On - Adapter has a fault.

Wrong slot

(Yellow) On - Adapter is in the wrong slot.

The wrong slot LED is ON only when an adapter that is plugged

into the multiaccess enclosure violates the plugging rules.

Green port (See

note). On - Port is operating normally (enabled and configured).

Off - Port is not configured or is disabled.

For the ESCON adapter:

Blinking - The optical power measurement test is running.

Yellow port (See

note). On - One or more ports has a hardware fault.

Blinking - One or more ports has a port I/O or network failure.

Use the Maintenance Analysis Procedures (MAPs) to isolate.

Off - No problem detected.

Note: The port LEDs of the multiport WAN adapters (FC 3282, FC 3291, and FC 3292)

reflect the status of one or more of the ports.

3746 PN 25L9934 EC F12604

FFBM 8 of 10 14/04/1998

IBML Installation Instructions

11.0 Test Procedures

No test required.

12.0 Field Updating

None.

3746 PN 25L9934 EC F12604

FFBM 9 of 10 14/04/1998 9

IBML Installation Instructions

After Installation (steps 13-15)

13.0 Publications Update

None.

14.0 Parts Disposition

None.

15.0 Machine Records

•Install the new MACHINE HISTORY supplied.

•Report installation and quality to existing procedures.

End of instructions.

3746 PN 25L9934 EC F12604

FFBM 10 of 10 14/04/1998

This manual suits for next models

Table of contents

Other IBM Controllers manuals

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual