Huawei SmartAX MA5800-X15 User manual

HUAWEI TECHNOLOGIES CO., LTD.

SmartAX MA5800-X15

Quick Installation Guide

Issue: 02

Date: 2017-03-31

About This Document

Change History

Symbol Conventions

Updates between document issues are cumulative. Therefore, the latest document issue

contains all updates made in previous issues.

The symbols that may be found in this document are defined as follows.

Symbol Description

Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Indicates a potentially hazardous situation which, if not avoided, could

result in equipment damage, data loss, performance deterioration, or

unanticipated results.

NOTICE is used to address practices not related to personal injury.

Calls attention to important information, best practices and tips.

NOTE is used to address information not related to personal injury,

equipment damage, and environment deterioration.

Updates in Issue 01 (2016-05-30)

This is the first release.

Intended Audience

This document describes how to install the MA5800-X15.

The intended audience is hardware installation engineers.

Updates in Issue 02 (2017-03-31)

Based on issue 01 (2016-05-30),Added 7.1 Cabinet with Routed Cables and 7.2 Routing the

External Power Cable and PGND Cable.

Content

1 Precautions …………………………………..…………………………............................………….1

2 Tools and Meters………………………….………………………….............................…………….2

3 Appearance and Structure……………………………………….............................…………….3

4 Environment Requirements on Third-Party Cabinets ……..………….…………….………4

5 Space Requirements on Third-Party Cabinets …………………………….………..…......5

5.1 When the Cabinet Accommodates One MA5800-X15 Subrack………….………….5

5.2 When the Cabinet Accommodates One MA5800-X15 Subrack and Another Device..6

6 Installing the Service Subrack……………….……………………...............................………...7

7 Routing Cable …………………………………….……………………...............................………..8

7.1 Cabinet with Routed Cables……………...........................................................................8

7.2 Routing the External Power Cables and PGND Cable......................................................9

7.3 Routing the Power Cables and PGND Cable of the Equipment ………..........................10

7.4 Routing Clock Cables………….......................................................................................11

7.5 Routing Network Cable..……….……..............................................................................12

7.6 Routing Trunk Cables………...........................................................................................13

7.7 Routing Optical Fibers (Upstream)..................................................................................14

7.8 Routing Optical Fibers (P2P Board)…............................................................................15

7.9 Routing Optical Fibers (GPON Board)............................................................................16

8 Post-Installation Check…………………………………………………...............................…...17

9 Powering on the System………………………………………..............................…................18

1 Precautions

•After routing the cable, attach the label or fasten the tag to the cable 20 mm away from the

connector.

•After the label for the signal cable is attached to the signal cable, the rectangular text area of

the label must face rightwards or downwards.

•After the identification plate for the power cable is attached to the power cable, the text area of

the plate must face rightwards or upwards. Ensure that the side attached with the label faces

outwards.

ESD gloves ESD wrist strap

Affixing labels / tags

•This document aims to provide simple and distinctive guidelines for hardware installation.

•This document does not describe operations for the pre-delivery installation. Instead, this

document describes only the operations for on-site installation.

Electrostatic Discharge

Before touching the device, or holding the boards and IC chips, wear the ESD gloves or the

ESD wrist strap to prevent the electrostatic discharge of the human body from damaging the

sensitive components. Ensure that the other end of the ESD wrist strap is properly grounded.

•The distance between cable ties or binding straps inside the cabinet must be within 250 mm.

(For user cable, the distance must be within 200 mm.)

•Use diagonal pliers to cut off the extra part of the cable tie to the end, and ensure that the

cable tie is neat without sharp edges to prevent hand injury.

Bundling cables

2 Tools and Meters

ESD gloves ESD wrist strap

Optical power meterMultimeter

Network cable

crimping tool Network cable tester

Before you begin, get the following tools ready.

Marker Flat-head screwdriver Phillips screwdriver Diagonal pliers

Optical fiber

cleaner

Optical fiber

microscope

3 Appearance and Structure

The MA5800-X15 service subrack, 11U high and 19 inches wide, has 20 slots and a fan try

on the top. The subrack is installed in the cabinet through the IEC mounting ears.

Unit: mm

442

482.6

Fan tray

Universal interface

board

Service board

Power board

Grounding point

Control

board

Mounting ear

ESD jack

Service board

486

287

4 Environment Requirements on Third-Party Cabinets

•Cabinet dustproof requirement: The MA5800-X15 subrack is not dustproof, so select

dustproof cabinets that support dust filter maintenance.

•Cabinet installation requirements:

For the MA5800-X15, select an IEC60297-compliantcabinet with a depth of 300 mm or

more so that a space with a depth of 55 mm or more can be reserved for cable/fiber routing

after boards are installed.

•Cabinet door requirement: When devices are operating, keep the cabinet door closed.

•Grounding requirement: Huawei cabinets are grounded through mounting bars. Ensure that

third-party cabinets are properly grounded based on site conditions.

•Power distribution requirements: Ensure that an over-current protection mechanism has

been deployed on the upper-level device.A 60-A over-current protection mechanism is

recommended for the MA5800-X15. Ensure that the circuit breaker trip value of the upper-level

device is greater than or equal to the rated value on the device nameplate.

•Heat dissipation requirements:

Ensure that the cabinet has an air inlet and the hole density of the cabinet door is 60% or

higher.

When a cabinet accommodates multiple subracks or the device shares a cabinet with other

active devices, ensure that the following space requirements are met.

•Reserve at least 2 U space for air flow-in when you route fibers or install other passive

devices. You are advised to reserve more than 4 U space to facilitate subsequent air inlet or

dust filter cleaning.

5 Space Requirements on Third-Party Cabinets

5.1 When the Cabinet Accommodates One MA5800-X15 Subrack

•The heat dissipation of the MA5800-X15 is assured only when more than 2 U space is

reserved at the air inlet and 3 U space is reserved at the air outlet.

•You are advised to reserve more than 4 U space above and under the MA5800-X15

respectively to minimize the impact on other components in the cabinet.

STATUSFAN

SCUN

RUN

ALM

ACT

RESET

LINKACT

CON ETH ESC

TX0

RX0

TX1

RX1

TX2

RX2

TX3

RX3

SCUN

RUN

ALM

ACT

RESET

LINKACT

CON ETH ESC

TX0

RX0

TX1

RX1

TX2

RX2

TX3

RX3

PRTE

RTN(+)

ALARM

NEG(-)

PRTE

RTN(+)

ALARM

NEG(-)

GPBD

RUN

ALM

BSY

PON

GPBD

RUN

ALM

BSY

PON

GPBD

RUN

ALM

BSY

PON

GPBD

RUN

ALM

BSY

PON

GPBD

RUN

ALM

BSY

PON

GPBD

RUN

ALM

BSY

PON

GPBD

RUN

ALM

BSY

PON

GPBD

RUN

ALM

BSY

PON

GPBD

RUN

ALM

BSY

PON

GPBD

RUN

ALM

BSY

PON

GPBD

RUN

ALM

BSY

PON

GPBD

RUN

ALM

BSY

PON

GPBD

RUN

ALM

BSY

PON

GPBD

RUN

ALM

BSY

PON

X2CS

RUN ALM

TX0

RX0

LINK ACT

TX1

RX1

X2CS

RUN ALM

TX0

RX0

LINK ACT

TX1

RX1

GPBD

RUN

ALM

BSY

PON

GPBD

RUN

ALM

BSY

PON

CITD

RUN

MAJ

MIN

IN0 OUT

COM ALMETH

IN1

BITS/TOD

Front view Side view

Airflow blockingobject

Without an air deflector Withan air deflector

Front view Side view Front view Side view

•Reserve 10 U space between the devices or add a 3 U air deflector to redirect air flows to

minimize the mutual heat dissipation impacts on the devices.

•Reserve at least 2 U space for air flow-in when you route fibers or install other passive devices.

You are advised to reserve more than 4 U space to facilitate subsequent air inlet or dust filter

cleaning.

5.2 When the Cabinet Accommodates One MA5800-X15 Subrack and

Another Device

5 Space Requirements on Third-Party Cabinets

10U

Air deflector (3 U)

6 Installing the Service Subrack

Determine the location of floating nuts

by using the installation template.

Install the upper and lower cable manager.

Install the service subrack.

Installation

template

Phillips screwdriver

Upper cable manager

Lower cable manager

Locate the installation positions of

the cable manager and service

subrack on the mounting bars, and

install captive nuts at these

positions.

Floating nut

Mounting bar (use a

flat-head screwdriver

if no mounting bar is

available.)

Table of contents

Other Huawei Network Hardware manuals

Huawei

Huawei CR52K-SFUC User manual

Huawei

Huawei EG8040F5 User manual

Huawei

Huawei EN83CTLC User manual

Huawei

Huawei EchoLife HG8245W5-6T User manual

Huawei

Huawei FusionModule2000-S User manual

Huawei

Huawei RTN510 User manual

Huawei

Huawei RRU3908 V2 Guide

Huawei

Huawei SMUC User manual

Huawei

Huawei OptiXstar P813E User manual

Huawei

Huawei OptiX OSN 8800 T64 User manual

Huawei

Huawei RT-FIC-1GBE User manual

Huawei

Huawei NetEngine-8000-M8 User manual

Huawei

Huawei CR-P1U User manual

Huawei

Huawei EchoLife EG8143H5 User manual

Huawei

Huawei CR-E4GC User manual

Huawei

Huawei PDU8000 Series User manual

Huawei

Huawei OptiX RTN PI-DC B10 Operating and safety instructions

Huawei

Huawei RRU3832 User manual

Huawei

Huawei FusionModule 500 User manual

Huawei

Huawei CR52-4xPOS/STM1-SFP User manual

Huawei

Huawei CR52-RPR/STM64-XFP User manual

Huawei

Huawei NE-FIC-CE3 User manual

Huawei

Huawei BTS3012 User manual

Huawei

Huawei OptiX RTN 600 ODU User manual

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Lanner

Lanner NCA-1020A user manual

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide