HP Visualize J280 - Workstation Manual

TABLE OF CONTENTS

Kit Contents 1............................

Installation Prerequisites 2.......

Tools 3........................................

Associated Documentation 3...

Upgrade Procedures 4..............

Powering Off the System 4......

Removing the Front Bezel 6....

Removing the Main Tray 7.......

Removing Memory DIMMs 9...

Installing Memory DIMMs 11.....

Installing the New J280 13.........

Installing the Storage 14............

Changing the Model Label 15....

Replacing the Front Bezel 17....

Installing the DC to DC 18.........

Verifying System Operation 25..

Filling Out the Return 25............

Kit Contents

Main Tray Assembly

 !  #!   ! " 

J280 Owner’s Guide

HP Part Number A2876–90013

! !! 

!! !

*Storage Tray Fan Kit (HP Part Number A2876–60011) with Storage Fan

Installation manual (HP Part Number A4081–90010)

 !" !

 Items marked with * are shipped in a seperate container.

Installation Prerequisites

Before the J280 Upgrade can be performed both the requisite version of HP–UX and

a supported graphics card must be installed (graphics card not required if system is

used with a RS–232 terminal as the console).

Operating System

Verify that the HP–UX operating system is at the minimum level of 10.20. This

software must be loaded on the system before performing this upgrade procedure.

Graphics Card Support

Verify that the graphics card(s) installed in your Model J200/210/210XC are

supported on the Model J280. The /usr/bin/graphinfo command will display the

current graphics card(s) information. Both HCRX8and HCRX24Z cards will require

a physical inspection of the card to verify the Z–Acclerator part number. The first 5

alpha–numaric characters on the Z Accelerators white label must read A4242 . The

Z– Accelerator is the small daughter card. If a graphics upgrade is required, it should

be performed prior to the J280 Upgrade. The graphics card(s) supported on the

Model J280 are:

HP VISUALIZE–8, 24, 48, 48XP, EG and Dual EG graphics cards

HCRX–8 (A4070A/B)

HCRX–24 (A4071A/B)

A4070A/B + A4242A (HCRX–8Z with the A4443A upgrade)

A4071A/B + A4242A (HCRX–24Z with the A4443A upgrade)

NOTE: The COLOR/DUAL COLOR(A4077/78A) graphic

card(s) will ot work with HPUX 10.20.

Tools

Flat blade screwdriver

10 TORX driver (needed for Storage Tray Fan upgrade)

Anti–static bag

Static strap

       

Associated Documentation

The following documents are associated with the upgrade kit.

J280 Service Handbook (HP Part Number A2876–90039)

J280 Owner’s Guide(HP Part Number A2876–90013)

J Class Storage Drawer Fan Install Guide (HP Part Number

A4081–90010)

Model J280 Upgrade Instructions J Class Workstations

HP Part Number A2876–90010 (This document)

Upgrade Procedures

The upgrade procedure consists of the following sections:

Powering Off the System

Removing the Front Bezel

Removing the Main Tray Assembly

Removing Memory DIMMs

Installing the new J280 Main Tray Assembly

Installing the Storage Tray Fan

Changing the Model Label

Replacing the Front Bezel

Installing the DC to DC Converter

Verifying system operation

        

Powering Off the System

Before performing this upgrade procedure, observe the following precautions:

1. The workstation must be running HP–UX 10.20 or later to accommodate the

J280 upgrade. If the workstation is running a version of HP–UX lower than

10.20, update the operating system software before continuing.

2. Determine the workstation’s LAN ID using the lanscan command by entering

the following:

/usr/sbin/lanscan

The output is similar to the following:

Hardware Station Dev Hardware Net–Interface NM Encapsulation Mjr

Path Address lu State NameUnit State ID Methods Num.

2.0.2 0x0800970ECC0 0 UP lan0 UP 4 ETHER 52

After you install the new tray assembly and power on the system for the first

time,youwillbepromptedforthe LANID. Recordthatinformation heresoyou

have a record of it:

EtherLAN ID ______________________–_____________________

You must supply the dash (–) between the first six digits and the last six digits.

3. Power down the system.

4. Unplug the system unit power cord and the power cords of any peripheral

devices from ac wall outlets.

5. Unplug the system unit power cord from the ac input connector at the back of

the system unit.

WARNING: To avoid electrical shock, make sure that you unplug the

power cable from the wall outlet and the system unit before

proceeding further.

CAUTION: The internal components of the workstation are sus-

ceptible to mechanical and electrostatic shock. To

prevent such damage from occurring, observe the

following precautions during the installation proce-

dure:

Stand on static–free mat

Wear a static–grounding wrist strap to ensure that any

accumulated electrostatic charge discharges from

your body to ground. Attach the static–grounding

wrist strap by following the instructions on the pack

age that contains the strap. Be sure to attach one end

of the strap to the system chassis.

Removing the Front Bezel

To remove the front bezel follow these steps:

CAUTION: Do not attempt to operate the workstation with the

front bezel removed. The bezel is needed to ensure

proper air flow for system cooling.

Figure 1. Removing the Front Bezel

1. Attach the static–grounding wrist strap by following the instructions on the

package. Attach the the sticky end of the wrist strap to bare metal on the

system unit.

2. Release the front bezel by pushing in the two locking tabs at the front of the

system unit as shown in Figure 1.

3. Swing the panel down and pull up slightly so the two guide pins on the bottom

clear their guides and lay the front bezel down.

Removing the Main Tray Assembly

To remove the Main Tray assembly follow these steps:

Figure 2. Removing the Tray Assembly

1. Remove the two screws in the center of the tray assembly.

2. Pull the ejector handles on the left side, top and bottom of the tray assembly to

release the board assembly from the internal connectors. Refer to Figure 2.

3. Pull the tray assembly straight out and place on a flat surface. This assembly is

heavy. Move it slowly and be sure it is properly supported.

Removing Memory DIMMs

To remove the memory modules from the CPU board, do the following:

1. Locate the memory DIMMs in the system unit, as shown in Figure 3.

Memory DIMMs

Figure 3.Memory DIMM Location

1. To remove a memory DIMM, push the ejector handles on the side of the

DIMM. Lift the memory DIMM up and out of the connector. Place the

memory DIMM on a static–free service. Figure 4 shows how to remove the

memory DIMM.

Other manuals for Visualize J280 - Workstation

Table of contents

Other HP Desktop manuals

HP Z600 - Workstation - 6 GB RAM User manual

HP Compaq Notebook Installation instructions

HP Sprout User manual

HP Deskpro 300 Operating and maintenance manual

HP Pavilion t134 User manual

HP Pavilion t270 User manual

HP EliteDesk 880 G5 Manual

HP TouchSmart 610-1200 User manual

HP Pavilion t124 User manual

HP Vectra VL6 6 User manual

HP dc5100 - Microtower PC Quick reference guide

HP Xw4400 - Workstation - 2 GB RAM User manual

HP 100B - All-in-One PC Operating manual

HP Deskpro EP MT 6400X SB User manual

HP Pavilion t490 Installation instructions

HP ProDesk 405 G1 Manual

HP Compaq Presario Specification sheet

HP RP9 G1 9118 Installation instructions

HP Compaq Presario Specification sheet

HP ProLiant WS460c Gen8 User manual

HP Pavilion t458d User manual

HP Net Vectra User manual

HP Workstation x1100 User manual

HP Pavilion xg900 - Desktop PC Manual

Popular Desktop manuals by other brands

Asus

Asus E210 Series user guide

Dell

Dell Inspiron 600m quick start

Dell

Dell Inspiron 3662 Service manual

TotalFlow

TotalFlow uFLO user manual

Logitech

Logitech MK320 quick start guide

Dell

Dell XPS 730 H2C Service manual

Sony

Sony Vaio Series operating instructions

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer quick start

Alto

Alto MD 250 instruction manual

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series user manual

Sony

Sony VAIO VGX-TP1 Series user guide

Asus

Asus Eee Box B204 user manual

Dell

Dell Optiplex 9010 All In One owner's manual

Everex

Everex eXplora user manual

Lenovo

Lenovo ThinkCentre M75e user guide

Dell

Dell Alienware Area-51 R4 Service manual