HP Model 744 - VME Workstation User manual

Installing the A4980A

EISA-to-PCI Backplane Upgrade

This upgrade is to be performed only by HP

qualiﬁed service personnel.

HP Part No. A4980-90601

Edition E0698

Printed in U.S.A.

2

Hewlett-Packard Co. 1998

Printing History

First Printing: June 1998

UNIX is a registered trademark in the United States and other countries,

licensed exclusively through X/Open Company Limited.

NOTICE

The information contained in this document is subject to change without

notice.

HEWLETT-PACKARD MAKES NO WARRANTY OF ANY KIND WITH

REGARD TO THIS MATERIAL INCLUDING BUT NOT LIMITED TO

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FIT-

NESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be lia-

ble for errors contained herein or for incidental or consequential damages in

connection with the furnishing, performance or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its

software on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copy-

right. All rights reserved. No part of this document may be photocopied,

reproduced or translated to another language without the prior written con-

sent of Hewlett-Packard Company.

RESTRICTED RIGHTS LEGEND. Use, duplication, or disclosure by gov-

ernment is subject to restrictions as set forth in subdivision (c) (1) (ii) of the

Rights in Technical Data and Computer Software Clause at DFARS

252.227.7013. Hewlett-Packard Co., 3000 Hanover St., Palo Alto, CA

94304.

10 9 8 7 6 5 4 3 2 1

3

Kit Contents

Kit Contents

Make sure that you have kit A4980A and that it contains the following

items:

• PCI backplane

• GSC-to-PCI interface board

Tools Required

You’ll need the following items to install the PCI Module:

• #1 Pozidriv screwdriver (with extension)

• T10 and T-15 Torx screwdrivers

• Static-free work area.

Prerequisites

1Stop any application programs, then shut down the system.

2Turn the system off, and unplug the power cord(s) and all other cables and

terminators from the system.

3If the system is mounted in a rack, remove it from the rack.

WARNING: To avoid electrical shock, make sure you unplug the power cable from the wall

outlet and the system unit before proceeding any further.

4

Prerequisites

CAUTION: The internal components of the system are susceptible to

mechanical and electrostatic shock. To prevent such damage from

occurring, observe the following precautions during the installation

procedure.

• Stand on a static-free mat

• Wear a static-grounding wrist strap to ensure that any accumulated

electrostatic charge discharges from your body to ground. Attach the

static-grounding wrist strap by following the instructions on the pack-

age that contains the strap. Be sure to attach one end of the strap to the

system chassis.

• Handle system and upgrade kit components carefully to prevent dam-

age from mechanical shock.

5

Installation

Installation

1Remove the system top cover (see Figure 1).

Figure 1 Removing the Top Cover

Screws Screws

Screws

6

Installation

2Remove the front bezel (see Figure 2).

Figure 2 Removing the Front Bezel

7

Installation

3Remove the two screws from the rear of the system, and slide the mid-tray

toward the front, and then up, out of the system (see Figure 3).

Figure 3 Removing the Mid-Tray

8

Installation

4Remove any installed EISA cards.

5Remove the EISA backplane/interface assembly (see Figure 4).

Figure 4 Removing the EISA Backplane Assembly

9

Installation

6Assemble the PCI backplane/interface assembly (see Figure 5).

Figure 5 Assembling the PCI Backplane Components

10

Installation

7Install the PCI backplane assembly into the chassis (see Figure 6).

Figure 6 Installing the PCI Backplane Assembly

NOTE: The PCI backplane only supports option cards with +5 volt bus signalling.

Other manuals for Model 744 - VME Workstation

8

This manual suits for next models

4

Table of contents

Other HP Computer Hardware manuals

HP

HP A1250 Series Assembly instructions

HP

HP HPE SimpliVity 325 User manual

HP

HP Integrity rx1600 User manual

HP

HP 64751 User manual

HP

HP 3000 III Series User manual

HP

HP Apollo r2800 Installation instructions

HP

HP Sangoma 2 Installation instructions

HP

HP 81200 User manual

HP

HP CB001A User manual

HP

HP Model 744 - VME Workstation User manual

HP

HP 6600 FIP-20 Flex Assembly instructions

HP

HP 98625A User manual

HP

HP Xw4600 - Workstation - 2 GB RAM Instruction sheet

HP

HP E3473A User manual

HP

HP 273914-B21 - Smart Array 6404/256 RAID... User manual

HP

HP Rp5700 - Point of Sale System Installation instructions

HP

HP USB 3.0 4-Port SuperSpeed PCIe x1 Card User manual

HP

HP Visualize c100 User manual

HP

HP FlexFabric 12908E LSXM108XFAN User manual

HP

HP Metal Jet S100 User manual

HP

HP HP 27113A Manual

HP

HP MicroServe User manual

HP

HP 8168E User manual

HP

HP Xw4600 - Workstation - 2 GB RAM User manual

Popular Computer Hardware manuals by other brands

EMC2

EMC2 VNX Series Hardware Information Guide

Panasonic

Panasonic DV0PM20105 Operation manual

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 user manual

Gigabyte

Gigabyte B660M DS3H AX DDR4 user manual

Raidon

Raidon iT2300 Quick installation guide

National Instruments

National Instruments PXI-8186 user manual

Hauppauge

Hauppauge WinTV-HVR-2250 Quick installation guide

Kontron

Kontron CP6002 user guide

Manhattan

Manhattan 702843 user manual

Aphex

Aphex 230 instruction manual

AMD

AMD Phenom II Product data sheet

Intel

Intel NUC 12 Pro user guide

dbx

dbx Zone Pro 1260 user manual

Galaxy

Galaxy GHDX2-2430S-24F4D Installation and hardware reference manual

Intel

Intel AXXRMFBU4 Quick installation user's guide

Kontron

Kontron DIMM-PC/MD product manual

ST

ST X-NUCLEO-SAFEA1B How to use

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 installation manual