HP Integrity rx1600 User manual

February 2004

Printed in the U.S.A.

Smart Array (A9890A) Cable Routing

The purpose of this document is to provide cable routing information when a Smart Array PCI-X RAID card (A9890A)

is used to drive the embedded hard disk drives. The existing SCSI cable connected to the Channel A connector on the

system board is relocated to the Channel A connector on the Smart Array PCI-X card installed in slot 1 (full-length slot)

of the PCI cage.

The SCSI cable is routed from the PCI cage under the power supply bracket and over the IDE cable, if installed, avoiding

blocking the airflow of the chassis fans.

Refer to the hp integrity rx1600 Operation and Maintenance Guide for detailed instructions on powering down the

server, extending the server from a rack, and removing and replacing covers and components.

1. Disconnect the SCSI cable from the Channel A connector on the system board by pulling on the cable release strap.

See figure 1.

Figure 1. SCSI Channel A Connector on System Board

2. Remove the PCI cage from the server.

3. Remove any accessory card installed in PCI slot 2 (half-length slot).

4. Install the Smart Array PCI-X RAID card (A9890A) in PCI slot 1 (full-length slot).

5. Orient the PCI cage with the installed PCI-X RAID card component-side-up allowing routing of the SCSI cable.

See figure 2.

Figure 2. Cable Routing on Smart Array Card and PCI Cage

NOTE If an optional management processor card is installed in the server, follow the

instructions provided in the hp integrity rx1600 Operation and Maintenance Guide to

remove the card, allowing access to the Channel A connector. Reinstall the card after the

SCSI cable has been disconnected.

Channel A

connector

Around heatsink

Exit parallel to

connector

Channel A1

Under slot 2 connector

6. Attach the SCSI Channel A connector (previously removed from the system board connector) to the A1 Channel of

the PCI-X RAID card.

7. Route the SCSI cable around the heatsink on the PCI-X RAID card and under the edge of the PCI slot 2 connector.

See figure 2.

8. Continue routing the cable parallel to the connector edge of the PCI cage.

9. Reinstall any accessory card previously removed from PCI slot 2.

10. Install the PCI cage into the server chassis.

11. Route the SCSI cable under the power supply bracket as shown in figure 3.

Figure 3. Route Cable under Power Supply Bracket

12. Route the SCSI cable through the access slot of the fan assembly to the connector on the SCSI backplane.

See figure 4.

Figure 4. Cable Routing at SCSI Cage

13. Complete the installation by following the instructions provided in the hp integrity rx1600 Operation and

Maintenance Guide for closing up the server, installing in a rack, and powering-up. To enable RAID refer to the

A9890A documentation.

NOTE The SCSI cable should be routed over the IDE cable if the IDE cable is present.

CAUTION Do not block the airflow of the chassis fans. Reduced airflow may cause overheating.

Power Supply

Bracket

Route over IDE

cable (if present)

Do not block fans

Other manuals for Integrity rx1600

This manual suits for next models

Table of contents

Other HP Computer Hardware manuals

HP QMH2672 User manual

HP FlexFabric 12908E LSXM108XFAN User manual

HP Metal Jet S100 User manual

HP MCS G2 Installation guide

HP HPE LSWM2XGT2PM User manual

HP Xw6600 - Workstation - 2 GB RAM User manual

HP MPIO Installation and operating manual

HP F1381A User manual

HP 3000 III Series User manual

HP Apollo r2800 Installation instructions

HP Z Turbo Drive Quad Pro User manual

HP StorageWorks FC1142SR User manual

HP Kayak XW U3-W3 User manual

HP USB 3.0 4-Port SuperSpeed PCIe x1 Card User manual

HP D7171A - NetServer - LPr User manual

HP Wireless USB Network Adapter hn215w User manual

HP Kayak XU04 Operator's manual

HP E5000 User manual

HP Notebook Series User manual

HP ProLiant DL140 User manual

HP 405132-B21 User manual

HP RDX USB 3.0 Instruction Manual

HP P Class 450/500/550/600/650/700/750 Manual

HP E2416B User manual

Popular Computer Hardware manuals by other brands

EMC2

EMC2 VNX Series Hardware Information Guide

Panasonic

Panasonic DV0PM20105 Operation manual

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 user manual

Gigabyte

Gigabyte B660M DS3H AX DDR4 user manual

Raidon

Raidon iT2300 Quick installation guide

National Instruments

National Instruments PXI-8186 user manual

Hauppauge

Hauppauge WinTV-HVR-2250 Quick installation guide

Kontron

Kontron CP6002 user guide

Manhattan

Manhattan 702843 user manual

Aphex

Aphex 230 instruction manual

AMD

AMD Phenom II Product data sheet

Intel

Intel NUC 12 Pro user guide

dbx

dbx Zone Pro 1260 user manual

Galaxy

Galaxy GHDX2-2430S-24F4D Installation and hardware reference manual

Intel

Intel AXXRMFBU4 Quick installation user's guide

Kontron

Kontron DIMM-PC/MD product manual

ST X-NUCLEO-SAFEA1B How to use

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 installation manual