Honeywell HSGN502 User manual
Please read this manual thoroughly before use, and keep it handy for future reference.
Rev.0
CEILING MOUNT HOUSING
WALL MOUNT HOUSING
HSGN502 / HSGN502-SH
Instruction Manual
FEATURES
Things to do before installing the indoor / outdoor dome housing:
- 2 -
1. Remove the bubble from the trim ring. (See Figure 1)
3. Insert the bubble so that the rim of the bubble comes into contact with adhesive tape
inside the indoor/outdoor dome housing s ring. Once the bubble is in position, gently
press around the edges so that the bubble sticks to the indoor/outdoor Ring.
4. Using the supplied RTV, fill up the gap between the bubble and the external ring.
(See Figure 2)
5. With the RTV in place, let it dry for at least 24 hours before covering the outdoor
housing.
2. Remove the protective paper from the adhesive tape located inside the indoor/outdoor
dome housing s external ring. (See Figure 2)
TRIMRING
FIGURE 1 FIGURE 2
RTVRTV
44
Wall Mount
1. Attach the mounting base ( ) to the ceiling or wall
using the supplied M6 screw ( ) and plastic bushing.
3. Wind the supplied Teflon sealing tape around the
threads on both ends of the pipe about 20 times.
4. Pull all the required cables through the base and pipe.
2. If there is strong sunlight, the optional sun shield
( ) must be used. Insert the sun shield into
the wall bracket.
5. Fit the pipe (whose threads are covered with Teflon tape)
into the base and turn until it is securely fastened.
Align the direction of the pipe turn the nut until lock auto mount base.
If the pipe is longer than 1M, the supplied metal base must be used to withstand stronger
force. Each end of the extension pipe should have PT1 1/4 threads.
6. Align the drop shaped housing ( ) with the pipe and turn until it is securely fastened.
7. Wire the heater and blower to the optional temperature control circuit.
8. Connect all the wires (24VAC, communication) to the push type terminal block.
9. Make sure that the wires are cleared and out of the way, before proceeding.
10. Install the ceiling adapter to the spacer using three M6 screws.
11. Set the dome ID (refer instruction manual).
12. Make sure that the lock handles on the inside of the ceiling adapter are pulled out.
13. Attach the dome camera to the ceiling adapter and push upward until you hear a click.
14. Make sure that the dome is safely locked into position before removing your hands from
the dome.
16. Once properly in place, tighten the external housing using the supplied M4 screw and
O rings.
15. Cover the housing with the prepared external ring which now contains the bubble.
Note that you must align "keys" inside the external housing with the "locks" on the
ceiling adapter.
33
99
1212
- 3 -
FEATURES
77
1818
2828
1515
1818
55
55
33
22
11
1616
2626
2525
2424
2323
2222
2121
2020
2121
1717
1313
1515
1212
1111
44
22
88
99
66
44
22
44
Unit: mm
2929
770.0 MAX
280.0 280.0
200
150
400
2727
129.0
P.C.D 112.0
M4 TAP(3X120 )
49.2
1- 1 /4 PF TAP
50.0
90.0
4- 5.5 HOLE
P.C.D 130.0
WELDING
1- 1 /4 PF TAP THRU
50.0
3.0
8.5
160.0
48.7
- 4 -
INSTALLATION
PRINTED IN KOREA
MECHANICAL
ELECTRICAL
Construction
Maximum Load
Finish
Input Voltage
Watt
Aluminum and steel
Light-gray polyester powder coat
Approx 4.4 lbs (2Kg)
24V AC
35 Watt (MAX) - For fan & heater
55 Watt (MAX) - For fan & heater + Dome
Weight
Approx 7.7 lbs (3.5Kg)
Approx 9.5 lbs (4.3Kg) - SUNSHIELD include
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Q TY
3
9
3
1
1
1
3
1
1
3
1
1
1
3
1
1
1
2
1
3
1
1
1
1
3
3
1
3
1
DESCRIPTION
PART NAME
PLASTIC BUSHING
O-RING (SMALL)
SCREW TAPPING (+)
MOUNT BASE (WALL)
SEAL TAPE
PIPE (STRAIGHT)
SNAP SCREW
o
PIPE (90 DEG ANGLE TYPE)
SUN SHIELD
SCREW WRENCH TYPE (SUS)
O-RING (LARGE)
EXTERNAL HOUSING
FAN & HEATER PCB
SCREW MACHINE (+)
SPACER
HEATER
BLOWER
SCREW MACHINE (+)
DOME CAN
SCREW MACHINE (+)
DOME MODULE
BUBBLE
GASKET
HOUSING RING
O-RING (SMALL)
SCREW TAPPING (+) (SUS)
MOUNT BASE (CEILING)
SCREW (+)
SET SCREW
ANCHOR ( 6.0mm)
P - 5
M6, L = 30mm
PF 1
TEFLON
PF 1 (L = 30cm / 11.8")
M6 X 15
PF 1 (L = 30cm / 11.8")
AL
M4 0.7, L = 12mm
AN - 158
AL
FR - 4
M3 0.5, L = 8mm
AL
30 Watt
DC 24V / 1.68W / D2440107S
M3 0.5
AL
M4 0.7, L = 8mm
HID2406CCXX
CLEAR
SILICONE
ABS
P - 4
M4, L = 10mm
PF 1 (LARGE)
M6 X 10mm
M4 X 4mm
EXPLODED ASSEMBLY PARTS LIST
SPECIFICATIONS
This manual suits for next models
1
Table of contents
Other Honeywell Security Camera manuals
Honeywell
Honeywell HEIPTZ-2201W-IR User manual
Honeywell
Honeywell HD4CH User manual
Honeywell
Honeywell HCC474M User manual
Honeywell
Honeywell HB73SPX User manual
Honeywell
Honeywell HD31H(X) User manual
Honeywell
Honeywell HD262 User manual
Honeywell
Honeywell HD4D3 User manual
Honeywell
Honeywell HCW2S2 User manual
Honeywell
Honeywell HD40 Series User manual
Honeywell
Honeywell H4W2PER2 User manual
Honeywell
Honeywell HD70 Series User manual
Honeywell
Honeywell EQUIP Series User manual
Honeywell
Honeywell HCX13M Manual
Honeywell
Honeywell HD4MDIP User manual
Honeywell
Honeywell HCM404LX User manual
Honeywell
Honeywell ACUIX ES Operator's manual
Honeywell
Honeywell HCX3W User manual
Honeywell
Honeywell HD4D3H User manual
Honeywell
Honeywell HZC-755N/P Series User manual
Honeywell
Honeywell HCD95534 User manual
