Honeywell HCD484L User manual

Document G-113079-002 – 02/07 – Rev 2

L-Series Color

Day/Night Camera

HCD484L HCD484LX

HCD485LX

User Guide

NTSC PAL

FrançaisDeutsch Italiano

Nederland Español English

Revisions

Issue Date Revisions

1.00 10/06 New document

2 02/07 Updated document part no.; added

warning to p. iii.

Rev 2 ii G-113079-002

02/07

Rev 2 iii G-113079-002

02/07

Warnings

Installation and servicing should be performed only by

qualified and experienced personnel to conform to all local

codes and to maintain your warranty.

WARNING! 12 VDC/24 VAC models require the use

of CSA Certified/UL Listed Class 2

power adapters to ensure compliance

with electrical safety standards.

Where the MAINS plug or an appliance coupler is used as

the disconnect device, the disconnect device shall remain

readily operable.

WEEE (Waste Electrical and Electronic Equipment).

Correct disposal of this product (applicable in the

European Union and other European countries with

separate collection systems). This product should be

disposed of, at the end of its useful life, as per applicable

local laws, regulations, and procedures.

Explanation of Graphical

Symbols

RISK OF ELECTRIC

SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE THE COVER.

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL

THIS SYMBOL INDICATES THAT

DANGEROUS VOLTAGE

CONSTITUTING A RISK OF

ELECTRIC SHOCK IS PRESENT

WITHIN THE UNIT.

THIS SYMBOL INDICATES THAT

IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS

ACCOMPANY THIS UNIT.

CAUTION

English

Rev 2 iv G-113079-002

02/07

FCC Compliance Statement

Information to the User: This equipment has been tested

and found to comply with the limits for a Class A digital

device. Pursuant to Part 15 of the FCC Rules, these limits

are designed to provide reasonable protection against

harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may

cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Caution Changes or modifications not expressly

approved by the party responsible for

compliance could void the user’s authority to

operate the equipment.

Manufacturer’s Declaration of

Conformance

The manufacturer declares that the equipment supplied

with this guide is compliant with the essential protection

requirements of the EMC directive 89/336/EEC and the Low

Voltage Directive LVD 73/23 EEC, conforming to the

requirements of standards EN 55013 for emissions.

Rev 2 G-113079-002

02/07

English

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . 2

Unpack Everything. . . . . . . . . . . . . . . . . . . . . . . . 2

Camera Functions . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Selecting the Lens . . . . . . . . . . . . . . . . . . . . . . . . 4

Adjusting the Back Focus . . . . . . . . . . . . . . . . . . . 5

Mounting the Camera. . . . . . . . . . . . . . . . . . . . . . . 6

Connecting the Camera . . . . . . . . . . . . . . . . . . . . 6

Remote Control Connections . . . . . . . . . . . . . 7

Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

On-Screen Display (OSD) . . . . . . . . . . . . . . . . . . 8

OSD Menu Functions . . . . . . . . . . . . . . . . . . . . 9

Saving your Settings . . . . . . . . . . . . . . . . . . . . 9

Setting Up Your Camera . . . . . . . . . . . . . . . . . . . 10

OSD Menu Structure . . . . . . . . . . . . . . . . . . . 10

Adding a Camera ID Or Title . . . . . . . . . . . . . 12

Setting the Camera Lighting Optimization . . 13

ELC / ALC Mode . . . . . . . . . . . . . . . . . . . . 13

White Balance Control Setup . . . . . . . . . . 14

Nightshot Control Setup . . . . . . . . . . . . . . . . . 15

Sync Control Setup . . . . . . . . . . . . . . . . . . . . . 16

Exit Setup Menu . . . . . . . . . . . . . . . . . . . . . . . 16

Warranty and Service . . . . . . . . . . . . . . . . . . . . . . . 17

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Rev 2 1 G-113079-002

02/07

Introduction

The Honeywell L-Series Day/Night Color cameras provide

high picture quality and resolution with a highly sensitive

1/3 inch interline transfer CCD image sensor.

Figure 1 Camera Overview

Features

• 1/3” IT Super HAD CCD

• C/CS adjustable lens mount adapter

• Excellent signal-to-noise ratio of more than 50 dB

• Minimum illumination of 0.1 lux (F1.2, 50 IRE, IR Filter

Off, B/W)

• Compatible with Video Iris (VSD) or Direct Drive (DC)

Auto Iris lens

• OSD menu control

• True color reproduction from various light sources

• Remote control with RS485 connection

Lens connector for

Auto Iris lens plug

Setscrew: loosen locking ring with a Phillips

screwdriver to adjust mounting ring.

C/CS mount adapter:

C mount: turn counterclockwise

CS mount: turn clockwise

Rev 2 2 G-113079-002

02/07

English

Before You Begin

Unpack Everything

Check that the items received match those listed on the

order form and packing slip. The L-Series Day/Night

packing box should include, in addition to this User Guide:

• One L-Series Day/Night Color camera

• One 4-pin connection cable

• One Auto Iris lens plug

If any parts are missing or damaged, contact the dealer you

purchased the camera from or call Honeywell Customer

Service (see Contact Information on the back of this

manual).

Note You will also require a Phillips screwdriver to

complete the installation.

Please read this guide carefully

before you install the L-Series Day/

Night Color camera.

Keep this guide for future reference.

Rev 2 3 G-113079-002

02/07

Camera Functions

Figure 2 Camera Rear View

PWR

VSD

VIDEO

~207-253VAC 50HZ

REMOTE UP

DOWN

GND

DC 12V

AC 24V

PWR VSD

VIDEO

DOWN

MENU REMOTE

Legend

#Description

1Auto Iris Lens select switch, VSD for Video or DC for

Directive Drive

2Video output connector

3Power input connector (24 VAC: 3 terminals)—Low Voltage

model only

4Power LED indicator

5Remote RS485 connector

6Menu control (see ”Programming” on page 8)

7Mains 230V Line Voltage power connector

Mains 230V—Line Voltage

(HCD485LX)

Low Voltage

(HCD484L, HCD484LX

Rev 2 4 G-113079-002

02/07

English

Installation

Selecting the Lens

Vari-focal Auto Iris lenses (Direct Drive or Video Drive) are

connected to the camera via a 4-pin square socket located

at the side of the camera.

1. Set the VSD/DC switch on the rear of the camera.

For Video Drive lens, set the switch to VSD.

For Direct Drive lens, set the switch to DC.

2. Set the EE MODE to ALC MODE on the OSD menu

(see ALC MODE).

Auto iris lens with amplifier: Set the VSD LENS on the

OSD menu.

Auto iris lens with no amplifier: Set the DC LENS on the

OSD menu. Adjust to the LEVEL carefully to avoid

hunting.

GND

DC 12V

AC 24V

PWR VSD

VIDEO

DOWN

MENU REMOTE

Low Voltage model shown

(HCD484L, HCD484LX)

VSD = Auto iris lens with a built-in

amplifier (video-type lens)

DC = Auto iris lens with no amplifier

(DC-type lens)

Rev 2 5 G-113079-002

02/07

Adjusting the Back Focus

The back focus adjustment is accessible at the front end of

the camera housing to adjust the back focal length or

picture focus.

The range of adjustment allows both C- and CS-mount

lenses to be used without the need for a spacer ring.

Figure 3 C/CS Mount

1. Loosen the setscrew with a Phillips screwdriver.

2. Adjust the focus ring to focus the picture.

3. Retighten the setscrew.

Figure 4 Auto Iris Lens Pin Definition

CCS

Setscrew

Pin DC (Direct Drive) lens Video (VSD) lens

1 CTRL- Power (+ 12V)

2CTRL+ NC

3DRV+ VideoSignal

4DRV- GND

Set the select switch to DC. Set the select switch to VSD.

Other manuals for HCD484L

This manual suits for next models

Table of contents

Languages:

Other Honeywell Security Camera manuals

Honeywell

Honeywell 30 Series User manual

Honeywell

Honeywell HBD92S User manual

Honeywell

Honeywell HWC-D101 User manual

Honeywell

Honeywell HEGS5300 User manual

Honeywell

Honeywell HD6A User manual

Honeywell

Honeywell HDZ302LIK User manual

Honeywell

Honeywell HD14C4HR6 User manual

Honeywell

Honeywell HCW2S2 User manual

Honeywell

Honeywell 3MP User manual

Honeywell

Honeywell HCCM474M Manual

Honeywell

Honeywell HBD92SX User manual

Honeywell

Honeywell EQUIP Series User manual

Honeywell

Honeywell 2450Cm Series User manual

Honeywell

Honeywell ACUIX ES User manual

Honeywell

Honeywell HD5 Series User manual

Honeywell

Honeywell HZC-755N/P Series User manual

Honeywell

Honeywell HDZP252DI User manual

Honeywell

Honeywell HCD95534 User manual

Honeywell

Honeywell Orbiter Platinum User manual

Honeywell

Honeywell HD4U User manual

Honeywell

Honeywell ScanDome II HSDN-251NS/PS Owner's manual

Honeywell

Honeywell HD4D Series User manual

Honeywell

Honeywell HD4DX User manual

Honeywell

Honeywell HD3DS User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications