Honeywell Pro-Watch 7000 User manual

Install Guide

Pro-Watch 7000

Intelligent Controller and System

PW7K1IC

All product and brand names are the service marks, trademarks, registered trademarks, or registered service marks of their

respective owners. Printed in the United States of America. Honeywell reserves the right to change any information in this

document at any time without prior notice.

Pro-Watch® is a trademark of Honeywell, Inc.

Ordering Information

Please contact your local Honeywell representative or visit us on the web at www.honeywellintegrated.com for information

about ordering.

Feedback

Honeywell appreciates your comments about this manual. Please visit us on the web at www.honey- wellintegrated.com to

post your comments.

Discover | Customer Portal

Self-Service Product Support and Learning Management System

https://honeywelldiscovertraining.com/login/discover/default.asp

YouTube | Honeywell Help and Support

https://www.youtube.com/channel/UCBEL6ouNV_LN5lEpYRujMTg/featured

PW-7000 (PW7K1IC) Installation and Configuration Guide, Document 800-25673V1 3

TABLE OF CONTENTS

Notices.......................................................................................................................................... 5

Warnings and Cautions......................................................................................................... 5

UL/ULC Warnings................................................................................................................... 6

CE + WEEE Marking................................................................................................................ 8

Damage During Shipment ................................................................................................... 9

Electro Static Discharge ....................................................................................................... 9

Disclaimer – Product Liability; Mutual Indemnification....................................... 10

Unpacking Procedure ......................................................................................................... 10

Shipping Instructions ......................................................................................................... 11

Limited Warranty .................................................................................................................. 11

Confidentiality ....................................................................................................................... 12

Compliance ............................................................................................................................. 12

Recommended testing and maintenance .................................................................. 12

Chapter 1 - ..................................................................... Product Overview13

PW-7000 and PW-6000........................................................................................................... 13

Port Settings.................................................................................................................................. 13

Other................................................................................................................................................. 15

Chapter 2 - Setting Up PW-7000 Hardware ............................................ 17

Setting the Jumpers................................................................................................................... 17

Setting the DIP Switches.......................................................................................................... 17

Bulk Erase Configuration Memory ................................................................................ 19

Bulk Erase ...................................................................................................................................... 19

Technical Specifications........................................................................................................... 20

Status LEDs................................................................................................................................... 20

Initialization ............................................................................................................................ 21

4 PW-7000 (PW7K1IC) Installation and Configuration Guide, Document 800-25673V1

Run Time Supplying Power to the PW-7000 Interface ..........................................22

Wiring ...............................................................................................................................................22

Supplying Power to the PW-7000 Interface .....................................................................23

Communications Wiring...........................................................................................................23

Cabinet Tamper and Power Failure Input Wiring............................................................24

Memory and Real Time Clock Backup Battery.................................................................25

Chapter 3 - System Configuration.............................................................. 27

Connecting to ACDSM for the First Time...........................................................................27

Login Page......................................................................................................................................28

Home Page .....................................................................................................................................28

Network Settings..........................................................................................................................28

Dynamic IP Configuration Method ................................................................................29

Static IP Configuration Method ......................................................................................30

Host Communication.................................................................................................................30

IP Server Connection Type ................................................................................................31

IP Client Connection Type .................................................................................................32

Device Information......................................................................................................................33

User Configuration......................................................................................................................33

Adding a User..........................................................................................................................34

Editing a User .........................................................................................................................35

Deleting a User.......................................................................................................................35

Restore Default Screen..............................................................................................................35

Apply Setting Screen ..................................................................................................................36

Log Out ............................................................................................................................................36

Chapter 4 - Reader Module........................................................................... 37

Reader Wiring .........................................................................................................................39

Input Wiring.............................................................................................................................39

Control Output Wiring.........................................................................................................40

PW-7000 (PW7K1IC) Installation and Configuration Guide, Document 800-25673V1 5

Notices

Wiring methods shall be in accordance with the National Electrical Code (ANSI/

NFPA70), Canadian Electrical Code, Part I (CSA C22.1) Safety Standard for Electri-

cal Installations, local codes, and the authorities having jurisdiction.

Warnings and Cautions

Note: See the Remote Enclosure Installation Manuals PW5K2ENC1/PW5K2ENC2 or

PW5K1ENC3 (not evaluated by UL) for installation instructions.

Before Installation

Before connecting the device to the power supply, verify that the output voltage is

within specifications of the power supply (see Technical Specifications beginning

on page 20).

Do not apply power to the system until after the installation has been completed.

Personal injury or death can occur, and the equipment can be damaged beyond

repair, if this precaution is not observed.

Fire Safety and Liability Notice (Not Evaluated by UL for fire, life safety, or burglary

application)

These fire and safety codes vary from city to city and you must get approval from

local fire officials whenever using an electronic product to control a door or other

barrier. Use of egress buttons, for example, may be illegal in some cities. In most

Caution: Disconnect power before servicing.

Caution: ATTENTION: Débranchez l'alimentation électrique avant

l'entretien.

Warning: Before installation, TURN OFF the external circuit breaker

which supplies power to the system.

Warning: AVERTISSEMENT: Avant de procéder à l'installation,

DESENCLENCHER le disjoncteur via lequel le système est

alimenté.

Warning: Never connect card readers to any critical entry, exit door,

barrier, elevator or gate without providing an alternative exit in

accordance with all the fire and life safety codes pertinent to

the installation.

Warning: AVERTISSEMENT: Ne jamais connecter de lecteur de carte en

un point critique (porte de sortie, barrière, ascenseur ou

portillon) sans proposer une autre sortie, ce afin de respecter la

règlementation en vigueur en matière d'incendie et de

protection des vies humaines, afférente à l'installation.

6 PW-7000 (PW7K1IC) Installation and Configuration Guide, Document 800-25673V1

applications, single action exit without prior knowledge of what to do is a life safety

requirement. Always make certain that any required approvals are obtained in writ-

ing. DO NOT ACCEPT VERBAL APPROVALS SINCE THEY ARE NOT VALID.

Honeywell Integrated Security never recommends using the PW-7000 or related

products for use as a primary warning or monitoring system. Primary warning or

monitoring systems should always meet the local fire and safety code require-

ments.

Failure to test a system regularly could make the installer liable for damages to the

end user if a problem occurs.

Earth Grounding

Use Suppressors

UL/ULC Warnings

The following applies to installations that require UL or ULC compliance:

Only UL/ULC Listed readers with standard Wiegand data output communication

format (protocol) have been evaluated for use with this system.

This product is intended to be installed indoors, within the protected premises.

Access Control System, Model PW7000, and Controller, Model PW7K1IC meet the

requirements for CAN/ULC-S319-05 Equipment Class 1. This product's compli-

ance to ULC-S319, Electronic Access Control Systems, will be considered invali-

dated through the use of any add-on, expansion, memory or other module

manufactured or supplied by the manufacturer or manufacturer's representative,

unless specifically evaluated by ULC.

All unused conduit holes must be properly plated or incorporate a Listed plug to fill

any voids.

All interconnecting devices must be UL/ULC Listed.

Shielded cable shall be employed for all Input/Output wiring.

Warning: The earth ground is connected at the factory and should not be

removed.

Warning: AVERTISSEMENT: La prise de terre est reliée à l'usine et ne doit

pas être retirée

Warning: Use suppressors on all door strikes. Use S-4 suppressors for

installation. Honeywell Integrated Security, Inc. recommends

only DC strikes.

Warning: AVERTISSEMENT: Employer des suppresseurs de surtensions

transitoires (S-4) sur toutes les gâches de porte. Honeywell

Integrated Security recommande l'utilisation exclusive de

gâches électriques à courant continu.

PW-7000 (PW7K1IC) Installation and Configuration Guide, Document 800-25673V1 7

Refer to the following Installation manuals for installation, connection, program-

ming, and operation instructions of the following sub-assemblies:

Note: Not Evaluated by UL for fire, life safety, or burglary applications.

Note: The earth ground is connected at the factory and should not be removed.

Do Not Connect To A Receptacle Controlled By A Switch.

Replacement 3 volt lithium coin cell must be one of the following:

Rayovac: BR2325 or BR2335-B

All interconnecting wire must be UL/ULC Listed, rated and suitable for the use.

The battery leads and primary AC main power wiring is non-power limited. This wir-

ing must be separated from all other wiring by at least 0.25" and cannot be

installed in the same conduit as any other power limited wiring.

The system must be configured to activate an alarm or trouble signal. Failure to do

so will not allow the access function to operate in the event of a tamper.

Note: The following applies to installations that require UL or ULC compliance:

• Only UL/ULC Listed readers with standard Wiegand data output

communication format (protocol) have been evaluated for use with this system.

• This product is intended to be installed indoors, within the protected premises.

• Access Control System, Model PRO4200, and Controller, Model PRO42IC meet

the requirements for CAN/ULC-S319-05 Equipment Class 1.

• This product's compliance to ULC-S319, Electronic Access Control Systems, will

be considered invalidated through the use of any add-on, expansion, memory or

other module manufactured or supplied by the manufacturer or manufacturer's

representative, unless specifically evaluated by ULC.

• All unused conduit holes must be properly plated or incorporate a Listed plug to

fill any voids.

Assembly Number Installation Manual Part Number

PW7K1IC 800-25673

PW7K1R2 800-25676

PW7K1IN 800-25674

PW7KOUT 800-25675

PW6K1IC 800-00005V3

PW6K1R2 800-01951V4

PW6K1IN 800-01952V1

PW6K1OUT 800-01953V1

PW5K2ENC1 and PW5K2ENC2 800-06952

PW5K1ENC3 800-06955V1

PW5K2ENC5 800-08421

PW6K2E2PS 800-08279V3

8 PW-7000 (PW7K1IC) Installation and Configuration Guide, Document 800-25673V1

Note: Total current draw for all included assemblies shall not exceed 4A, including input

rating and output load current.

• Suitable for S319, Class I

• Suitable for the following UL293/UL294 Performance Levels:

• Endurance: IV

• Standby: I

• Line Security: I

• Attack: I

• Suitable panic or exit hardware shall be employed for fail secure applications.

For UL293 applications, the Sys Fault contacts of the power supply and the door

held, door forced shall be monitored by suitable audible device.

CE + WEEE Marking

Description of the used symbol.

CE -Standard -Logo. This product complies with

the harmonized Regulation of the EU

WEEE symbol.It indicates this product is to be

recycling and not been thrown in the dustbin

PW-7000 (PW7K1IC) Installation and Configuration Guide, Document 800-25673V1 9

Damage During Shipment

Electro Static Discharge

Note: This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment.This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

installation and user guides, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the

interference at his own expense.

Note: This document and the data in it shall not be duplicated, used or disclosed to others

for procurement or manufacturing, except as authorized by and with the written

permission of Honeywell Integrated Security, Inc. The information contained in this

document or in the product itself is the exclusive property and trade secrets of

Honeywell Integrated Security, Inc. Copyright laws of the United States protect all

information in this document or in the software product itself.

Note: Any use of this product is subject to the terms and acceptance of the Honeywell

Integrated Security, Inc. Software Agreement. Please request a copy from Honeywell

Integrated Security, Inc. (http://www.honeywellintegrated.com/index.html), and

review the agreement carefully.

Caution: IF ANY DAMAGE TO THE SHIPMENT IS NOTICED, A CLAIM

MUST BE FILED WITH THE COMMERCIAL CARRIER

RESPONSIBLE FOR THE DAMAGE.

Caution: ATTENTION: SI L'EQUIPEMENT A SUBI DES DOMMAGES LORS

DE SON TRANSPORT, ADRESSER UNE RECLAMATION AU

TRANSPORTEUR RESPONSABLE.

Caution: Electro-static discharge (ESD) can damage CMOS integrated

circuits and modules. To prevent damage always follow these

procedures:

• Use static shield packaging and containers to transport all electronic

components, including completed reader assemblies.

• Handle all ESD sensitive components at an approved static-

controlled workstation. These workstations consist of a desk mat,

floor mat and an ESD wrist strap. Workstations are available from

various vendors.

Caution: ATTENTION: Des décharges électrostatiques peuvent

endommager les modules et circuits intégrés CMOS.

10 PW-7000 (PW7K1IC) Installation and Configuration Guide, Document 800-25673V1

Disclaimer – Product Liability; Mutual Indemnification

If a Customer receives a claim that a Product or any component thereof has caused

personal injury or damage to the property of others, Customer shall immediately

notify Honeywell Integrated Security in writing of all such claims. Honeywell Inte-

grated Security shall defend or settle such claims and shall indemnify and hold

Customer harmless for any costs or damages including reasonable attorneys’ fees

which Customer may be required to pay as a result of the defective Product or the

negligence of Honeywell Integrated Security, its agents, or its employees.

Customer shall hold harmless and indemnify Honeywell Integrated Security from

and against all claims, demands, losses and liability arising out of damage to prop-

erty or injury to persons occasioned by or in connection with the acts or omissions

of Customer and its agents and employees, and from and against all claims,

demands, losses and liability for costs of fees, including reasonable attorneys’ fees,

in connection therewith.

Unpacking Procedure

All containers should be opened and unpacked carefully in order to prevent dam-

age to the contents.

Follow these steps to unpack equipment in preparation for installation:

1. Open the container and remove the unit(s) and all packing material. Retain the

container and all the packing materials. They may be used again for reshipment

of the equipment, if needed.

2. Inspect the contents to see if anything is missing. If you notice any missing

items, contact the order entry department at 1-800-323-4576 Option-1.

3. Visually check the contents. If you see any damage, do the following:

a. If shipping has caused damage to the unit, a claim must be filed with the

commercial carrier.

b. If any other defect is apparent, call for a return authorization.

Caution: If any damage to the shipment is noticed before unpacking, a

claim must be filed with the commercial carrier.

Caution: ATTENTION: SI L'EQUIPEMENT A SUBI DES DOMMAGES LORS

DE SON TRANSPORT, ADRESSER UNE RECLAMATION AU

TRANSPORTEUR RESPONSABLE.

Other manuals for Pro-Watch 7000

This manual suits for next models

Table of contents

Other Honeywell Controllers manuals

Honeywell

Honeywell CENTRA LINE EAGLEHAWK Installation and operation manual

Honeywell

Honeywell IAQ Poin User manual

Honeywell

Honeywell B User manual

Honeywell

Honeywell SUPER TRADELINE S8610U User manual

Honeywell

Honeywell T775U Series User manual

Honeywell

Honeywell PP904A User manual

Honeywell

Honeywell SEC-H-600 User manual

Honeywell

Honeywell J48 User manual

Honeywell

Honeywell H46C User manual

Honeywell

Honeywell RM7800E User manual

Honeywell

Honeywell R7426A User manual

Honeywell

Honeywell Ex-Or MLS Installation and operation manual

Honeywell

Honeywell P906C Operation manual

Honeywell

Honeywell M7061 User manual

Honeywell

Honeywell Fire-Lite Alarms BG-12LPSP User manual

Honeywell

Honeywell PRESSURETROL L404F Operation manual

Honeywell

Honeywell Experion C300 User manual

Honeywell

Honeywell ComfortPoint Open CPO-PC400-W User manual

Honeywell

Honeywell EXCEL 5000 OPEN ZAPP User manual

Honeywell

Honeywell Touchpoint Plus User manual

Honeywell

Honeywell LeakFilm MC User manual

Honeywell

Honeywell UDC2800 User manual

Honeywell

Honeywell LP1501 Operator's manual

Honeywell

Honeywell AQUASTAT L4188A User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual