Heath Zenith 595-5684-09 User manual

Wireless Plug-In

Chime

This package includes (Style of push button and

chime may vary from illustration):

• Wirelessplug-inchime

• Wirelesspushbuttonwithbattery (Specic

models include 2)

• Hardwarepack

1. Install alkaline type A23 12 volt push button

battery (included). Remove back of case by

pushingintabonbottomwithasmallscrew-

driver (see Figure 1).See diagram inside push

button for correct battery orientation. Note: If

batteries are preinstalled, remove orange

battery tab.

2. Plug in wireless chime. To reduce the risk of

electrical shock, this equipment has a polar-

izedplug(onebladeiswiderthantheother).

Thisplugwilltinapolarizedoutletonlyone

way.Iftheplugdoesnottfullyintheoutlet,

reversetheplug.Ifitstilldoesnott,contacta

qualiedelectriciantoinstalltheproperoutlet.

Do not attempt to bypass this safety feature.

Test range. Temporarily position push button

whereyouwantitmounted.Presspushbutton

toverifychimeandpushbuttonworkproperly.If

chime does not sound, see Troubleshooting.

Figure 1

WARNING:To prevent possible SERI-

OUS INJURY or DEATH:

     

batteries.

     



-2- 595-5684-09

4. Adjust volume control (Available on se-

lected chimes). Unplug chime and adjust

volume control to desired volume (see Figure

2).Plugchimebackintowalloutlet.

5. Mount push button.Useeitherscrewsor

double sided tape to mount push button.

• Screw Mounting: Tomountwithscrews,

remove back of case by pushing in tab on

bottomwithasmallscrewdriver(seeFigure

1). Note:Removematerialinscrewholes

(ifneeded)before mounting with screws.

Attachbackofcasetodoorjamborwall(see

Figure 3). Snap front of push button on.

• Tape Mounting:Whenattachingpushbut-

ton using double sided tape, make sure the

surfaceofthedoorjamborwallisclean.

Figure 3

Figure 2

Chime Volume Control

(Selected Chimes)

Jumper Access Door (See

Tune or Code Section)

-3-

595-5684-09

Yourwirelesschimehasdifferentselectabletunes:Ding (one note), Ding-Dong

(twonote),orWestminster (eight note) (Available on selected chimes). The

factorysettingisfortheDing-Dongtune(orWestminster,whenavailable).This

tunecanbechangedbyfollowingtheinstructionsbelow.

• Ding (one note tune)

 InsidePushButton:Addajumpertolocation8.

• Ding-Dong(twonotetune)

 InsidePushButton:Removejumperfromlocation8.

Chime: Remove jumper from location 8.

• Westminster (Eight note tune) (Available on selected chimes)

 InsidePushButton:Removejumperfromlocation8.

Chime: Add a jumper to location 8.

Note:Allmodelshavebothfrontandbackdoortunecapabilities.Werecommend

the back door use the Ding tune and the front door use the Ding-Dong tune

(or Westminstertune,availableonselectedchimes).Modelsthatincludetwo

pushbuttonswillcomefactorysetforfrontandbackdoors.Decalsontherear

ofthepushbuttonwillindicateitssetting.

Note: Some models might require the use of

tweezerstoremoveandreplacethejumpers.

Figure 4

1 2 3 4 5 6 7 8

InsidePush

Button

Tune Setting

12345678

Removescrewto

open access door

BackofChime

Tune Setting

(Not used on all

models)

  

    

reconnecting to power.

Tune Settings

-4- 595-5684-09

Troubleshooting

A. Chime does not sound:

• Makesurepushbuttonandchimecodesarethesame(seeFigure5).

• Checkorientationofpushbuttonbattery(Seediagraminsidepushbutton

for correct battery orientation.)

• Checkchargeofpushbuttonbattery,replaceifnecessary.

• Makesuretheplug-inchimehaspowergoingtoit.

Chime is receiving

interference from another wireless device; change the code setting (see

Code Settingbelow).



• Donotmountchimeorpushbuttononmetalornearmetalstuds.This

reducesthetransmitterrange.Use1/4"to1/2"(6to13mm)woodshims

to move chime or push button off metal surface.

• Concreteoorsmayreducerange.Movechimeawayfromoor.

• Trylocatingchimeclosertopushbutton.

D. Code Setting:

  

     

reconnecting to power.

It is recommended to only change one code position at a time and then check

to see if system is functioning properly.

1. Unplugchimefrompowersource.

2. Open the cases and locate the jumpers on both the push button and chime

(see Figure 5).

3. The push button and chime both have eight different jumper locations.Jumper

positions 1 through 7 are used for setting the code.

-5-

595-5684-09

12345678

Removescrewto

open access door

BackofChime

4. Tochangethecode,either(Formodelswith2pushbuttons,changecode

setting in both push buttons to match chime.):

• Addajumpertothesamelocationonboththepushbuttonandthechime

or...

• Removeajumperfromthesamelocationonboththepushbuttonandthe

chime or...

• Moveajumperonthepushbuttonfromonelocationtoanother.Movethe

correspondingjumperonthechimetomatchthenewlocationinthepush

button.

Example: Move jumper at location “5” to location “4” on both the push

button and the chime.

Note:



Note:Unitwillcomefactorysetwithjumpersinlocations5,6,and7onthe

push button and on the chime (see Figure 5).

The range of the wireless chime canvary with location, temperature,and

battery condition.

* Code Settings 1-7

MustMatchBothPush

ButtonandChime

InsidePush

Button

Note: Some models might require the use of

tweezerstoremoveandreplacethejumpers.

Figure 5

12345678

-6- 595-5684-09

Technical Service





Ifyouexperienceaproblem,followthisguide.Youmayalsowanttovisitour

Websiteat:www.hzsupport.com. If the problem persists, call* for assistance

at 7:30AMto4:30PMCST(M-F).Youmayalsowrite*to:

HeathCo LLC

P.O.Box90045,BowlingGreen,KY42102-9045

ATTN: Technical Service

*IfcontactingTechnicalService,pleasehavethefollowinginformationavailable:

ModelNumber,DateofPurchase,andPlaceofPurchase.



-





ThisdevicecomplieswithPart15oftheFCCRulesandRSS-210ofIndustry

Canada.Operationissubjecttothefollowingtwoconditions:(1)thisdevicemay

not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Theuseriscautionedthatchangesormodicationsnotexpresslyapprovedby

the party responsible for regulatory compliance could void the user’s authority

to operate the equipment.

-7-

595-5684-09

HeathCoLLCreservestherighttodiscontinueandtochangespecications

atanytimewithoutnoticewithoutincurringanyobligationtoincorporatenew

features in previously sold products.

LIMITED WARRANTY

Thisis a“LimitedWarranty” whichgivesyouspeciclegal rights.You

mayalsohaveotherrightswhichvaryfromstatetostateorprovince

to province.

Foraspeciedperioddependinguponmodel(seechartbelow)fromthe

date of purchase, any malfunction caused by factory defective parts or

workmanshipwillbecorrectedatnochargetoyou.

Not Covered - Repair service, adjustment and calibration due to misuse,

abuse or negligence, light bulbs, batteries, and other expendable items

arenotcoveredbythiswarranty.Unauthorizedserviceormodicationof

theproductorofanyfurnishedcomponentwillvoidthiswarrantyinits

entirety.Thiswarrantydoesnotincludereimbursementforinconvenience,

installation, setup time, loss of use, unauthorized service, or return ship-

ping charges.

ThiswarrantycoversonlyHeathCoLLCassembledproductsandisnot

extended to other equipment and components that a customer uses in

conjunctionwithourproducts.

THISWARRANTYISEXPRESSLYINLIEUOFALLOTHERWARRAN-

TIES,EXPRESSORIMPLIED,INCLUDINGANYWARRANTY,REPRE-

SENTATIONORCONDITIONOFMERCHANTABILITYORTHATTHE

PRODUCTSAREFITFORANYPARTICULARPURPOSEORUSE,AND

SPECIFICALLYINLIEUOFALLSPECIAL,INDIRECT,INCIDENTAL,OR

CONSEQUENTIALDAMAGES.

REPAIRORREPLACEMENTSHALLBETHESOLEREMEDYOFTHE

CUSTOMER ANDTHERESHALLBENOLIABILITYONTHE PART

OF HEATHCO LLCFORANYSPECIAL,INDIRECT,INCIDENTAL,OR

CONSEQUENTIALDAMAGES,INCLUDINGBUTNOTLIMITEDTOANY

LOSSOFBUSINESSORPROFITS,WHETHERORNOTFORESEE-

ABLE.Somestatesorprovincesdonotallowtheexclusionorlimitation

of incidental or consequential damages, so the above limitation or exclu-

sion may not apply to you. 



Model Warranty Period

6140 and 6150 Series 1 Year

6160 Series 5 Years

-8- 595-5684-09



Inalámbrica

Este paquete tiene (El estilo del pulsador y de la

campana puede variar de la ilustración):

• CampanaEnchufableInalámbrica

• Pulsadorinalámbrico con batería(Modelos

específcosincluyen2)

• Paquetedeferretería

1. Instalar pila alcalina de botón tipo A23

de 12 voltios (Se incluye). Extraer la parte

posterior de la caja presionando la aleta en el

botón con un destornillador pequeño (vea la

Figura 1).Vea el diagrama dentro del pulsador

para la orientación correcta de la pila. Nota:

Silasbateríasestánpreinstaladas,quitela

aletaanaranjadadelasbaterías.

   Para

reducir el riesgo de choque eléctrico, este

equipo tiene un enchufe polarizado (una

patillaesmásanchaquelaotra).Esteen-

chufepodráinsertarseenuntomacorriente

polarizado solamente de una manera. Si el

mismo no entra completamente en el toma-

corriente, invierta el enchufe.Si aún no encaja

completamente, póngase en contacto con un

electrista competente para qua éste instale el

tomacorriente correcto. No trate de suprimir

estacaracterísticadeseguridad.



posible LESIÓN SERIA o LA MUERTE:

 

de las baterías.

 -

diatamente al doctor.

Figura 1

-9-

595-5684-09

3. Pruebe el alcance.Pongaprovisionalmente

el pulsador en la posición donde lo quiera

instalar. Presione el pulsador paravericar

que la campanay el pulsador funcionen

apropiadamente. Si la campana no suena,

vea Análisis de Averías.

Ajuste del control del volumen (Disponible

en los timbres seleccionados). Desenchufe

la campana y ajuste el control del volumen al

volumen deseado (vea la Figura 2). Enchufe

de nuevo la campana en el tomacorriente de

la pared.

5. Instale el pulsador. Use ya sean tornillos o

cinta adhesiva por ambas caras para instalar

el pulsador.

• Montaje con tornillos:Paramontarcon

tornillos,quitelapartedeatrásdelacaja

empujando hacia adentro la lengüeta de

abajo con un destornillador pequeño y

girando la cuchilla (vea la Figura 1). Nota:

Quite la suciedad de los orificios para

tornillos (si es necesario) antes de poner

lostornillos.Coloquelapartedeatrásde

la caja contra la jamba o la pared (vea la

Figura 3). Encaje a presión la parte frontal

del pulsador.

• Montaje con cinta adhesiva: Cuando

jeelpulsadorusandocintaadhesivapor

ambascaras,asegúresequelasupercie

de la pared o la del batiente de la puerta

estén limpias.

Control del Volumen de

la Campana (Campanas

seleccionadas)

Puertadeaccesoalpuente

(Vea la sección de Tonos o

Códigos)

Figura 3

Figura 2

-10- 595-5684-09

Sucampanainalámbricatienetonosdiferentesquepuedenseleccionarse:Tilín

(una nota), Tilín-Talán (dos notas), o Westminster (ocho notas) (Disponible

enlostimbresseleccionados).LacalibracióndefábricaeseltonoTilín-talán

(oeltonoWestminstercuandoestádisponible).Estetonopuedesercambiado

siguiendo las instrucciones que siguen.

• Tilín (tono de una nota)

 DentrodelPulsador:aumenteunpuentealsitio8.

• Tilín-talán (tono de dos notas)

 DentrodelPulsador:Quiteelpuentedelsitio8.

Campana: Quite el puente del sitio 8.

• Westminster (tono de ocho notas) (Disponible en los timbres seleccionados)

 DentrodelPulsador:Quiteelpuentedelsitio8.

Campana: Aumente un puente al sitio 8.

Nota: Todas las campanas tienen capacidad de tonos para las puertas frontal y

posterior. Recomendamos que la puerta posterior use el tono Tilín y la puerta

frontal el tono Tilín-Talán (o el tono Westminster, disponible en los timbres

seleccionados). Los modelos que incluyen dos pulsadores vendrán con la

calibracióndefábricaparalaspuertasfrontalyposterior.Lascalcomaníasen

laparteposteriordelpulsadorleindicaránlacalibración.

Nota:Algunosmodelospodríanrequerir

el uso de pinzas especiales para retirar y

colocar los puentes.

Dentro del

Pulsador

Figura 4

1 2 3 4 5 6 7 8

12345678

Quite el

tornillo para

abrir la puerta

de acceso

Programacióndel

tono (No se usa en

todos los modelos)

Partedeatrás

de la campana

Programación

del tono



de alimentación antes de abrir la puerta de acceso de códigos. Cierre

la puerta y ponga los tornillos antes de reconectar la alimentación.

Programación del tono

Table of contents

Languages:

Other Heath Zenith Accessories manuals

Heath Zenith

Heath Zenith Weatherproof Long Range Wireless Chime with Chime Extender... User manual

Heath Zenith

Heath Zenith SL-6166 User manual

Heath Zenith

Heath Zenith SL-7464-03 User manual

Heath Zenith

Heath Zenith 7750 User manual

Heath Zenith

Heath Zenith 5867 Service manual

Heath Zenith

Heath Zenith Notifi elite User manual

Heath Zenith

Heath Zenith 7762 User manual

Heath Zenith

Heath Zenith 7776 User manual

Heath Zenith

Heath Zenith SL-6168 User manual

Heath Zenith

Heath Zenith 6106 User manual

Heath Zenith

Heath Zenith 3106978 (AC-6196) User manual

Heath Zenith

Heath Zenith 6180 Series User manual

Heath Zenith

Heath Zenith 7306 User manual

Heath Zenith

Heath Zenith 121AC User manual

Heath Zenith

Heath Zenith 7143 User manual

Heath Zenith

Heath Zenith SL-6155 Series User manual

Heath Zenith

Heath Zenith Wireless Push Button Accessory 598-1105-05 User manual

Heath Zenith

Heath Zenith DUAL BRITE SL-5597 User manual

Heath Zenith

Heath Zenith Decorative Wireless Chime 598-1000-07 User manual

Heath Zenith

Heath Zenith Wireless Mechanical Battery Operated Chime... User manual

Heath Zenith

Heath Zenith SL-6200 User manual

Heath Zenith

Heath Zenith notifi alert User manual

Heath Zenith

Heath Zenith Decorative Wireless Chime 6180 User manual

Heath Zenith

Heath Zenith SL-6153 User manual

Popular Accessories manuals by other brands

Hillco

Hillco 2810 Operator's manual

Siemens

Siemens QSA2700D Basic documentation

Contours

Contours ZY024 manual

Saivod

Saivod VS621 manual

Virtuox

Virtuox VirtuCLEAN 2.0 user manual

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS user manual

Z-Wave

Z-Wave HSD-200Z user manual

turck

turck FMX-IM-2UPLI63FX quick start guide

Decagon Devices

Decagon Devices 10HS manual

UPPAbaby

UPPAbaby Cup Holder user manual

Elko

Elko SmartSensor Leakage Wireless manual

Grizzly

Grizzly H8371 instructions

Panasonic

Panasonic HG-T Series user manual

IFM Electronic

IFM Electronic Efector 250 Series Brief instructions

DigiDesign

DigiDesign 888/24 I/O installation guide

PROZIS

PROZIS QUAY user manual

patagonia

patagonia PSI Vest user manual

SFC Energy

SFC Energy EFOY GO! manual