Heath Zenith 7776 User manual
© 2015 HeathCo LLC
Wireless Plug-In
Night Light Chime
Figure 1
Note: The night light
feature is controlled by
a photocell and turns on
and off automatically as
the surrounding light level
changes.
Photocell
Orange Tab
This package includes (Style of push button and chime may vary from illustration):
Model
Wireless
strobe
chime
Wireless push
button
Hardware
pack
7776 ✔ ✔ ✔
1. Remove orange battery tab from push
button. Remove back of case by pushing in
tab on bottom with a small screwdriver (see
Figure 1). Remove orange battery tab.
2. Plug in wireless chime.
3.
Test range. Temporarily position push button
where you want it mounted.Press push button
to verify chime and push button work properly.
If chime does not sound, see Troubleshooting.
4. Adjust volume control to desired volume
(see Figure 2).
WARNING: To prevent possible
SERIOUS INJURY or DEATH:
• NEVER allow small children near
batteries.
• If battery is swallowed, immediately
notify doctor.
Figure 2
Chime Volume
Control
2
5. Mount push button. Use either screws or
double sided tape to mount push button.
• Screw Mounting: To mount with screws,
remove back of case by pushing in tab on
bottom with a small screwdriver (see Figure
1). Note: Remove material in screw holes
(if needed) before mounting with screws.
Attach back of case to door jamb or wall (see
Figure 3). Snap front of push button on.
• Tape Mounting: When attaching push but-
ton using double sided tape, make sure the
surface of the door jamb or wall is clean.
Figure 3
3
PRESS/HOLD TUNE: 1 SEC
SYNC: 3 SEC RESET: 10 SEC
Inside Push Button
Chime
Tune Settings
Tune Setting Table
Tune Push Button Chime
Ding Jumper - ON ———
Ding-Dong or
Westminster
Jumper - OFF Press button on chime. Listen
for single “Beep” tone. Release
button. Listen for selected tune.
Repeat to select different tune.
The chime has different selectable tunes: Ding
(one note tune), Ding-Dong (two note tune), or
Westminster (eight note tune). The factory set-
ting is for the Westminster tune. This tune can
be changed by following the instructions in the
Tune Setting Table.
Note: All chime models are designed to work
with up to 10 push buttons (sold separately). All
chimes are designed to play only two different
tunes no matter how many push buttons are used.
4
Troubleshooting
1. PROBLEM: Chime does not sound or rang one time and quit.
A. POSSIBLE CAUSE: Push button battery is not installed correctly.
A. CORRECTIVE ACTION: Make sure battery is installed according to the
diagram inside the push button.
B. POSSIBLE CAUSE: Push button battery is dead.
B. CORRECTIVE ACTION: Check charge of push button battery and replace
if necessary.
C. POSSIBLE CAUSE: Chime is not receiving power.
C. CORRECTIVE ACTION: Make sure the plug-in chime has power.
D. POSSIBLE CAUSE: Push button and chime are not synced.
D. CORRECTIVE ACTION: Sync the push button and chime.
• Press and hold the button on the chime until the chime sounds a
“Beep-Beep”.
• Press the push button within 30 seconds. The chime will sound a
“Beep-Beep” tone to indicate the push button is synced.
• Press the push button to ensure operation.
2. PROBLEM: Push button battery seems okay, but the chime does not work
after installation.
A. POSSIBLE CAUSE: Chime or push button is mounted on metal or near
metal studs. Note: Metal reduces transmission range.
A. CORRECTIVE ACTION: Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims
to move chime or push button away from metal surface.
B. POSSIBLE CAUSE: Chime is mounted near concrete floor or wall.Note:
Concrete may reduce range.
B. CORRECTIVE ACTION: Move chime away from concrete surface.
C. POSSIBLE CAUSE: Chime and push button are installed too far apart.
C. CORRECTIVE ACTION: Locate chime closer to push button.
5
3. PROBLEM: Chime sounds when not intended (false triggers).
POSSIBLE CAUSE: Chime is receiving interference from another wire-
less device.
CORRECTIVE ACTION: Reset chime and push button.
• Remove push button batteries. Wait 30 seconds.
• Press and hold the push button for 10 to 15 seconds within 60 seconds
after installing battery into the push button.
• Press and hold the button on the chime until the chime sounds a
“Beep-Beep-Beep-Beep”.
• To re-sync the push button and chime, press and hold the button on
the chime until the chime sounds a “Beep-Beep”.
• Press the push button within 30 seconds. The chime will sound a
“Beep-Beep” tone to indicate the push button is synced.
• Press the push button to ensure operation.
Note: The push button and chime come synced from the factory. The range of
the wireless chime can vary with location, temperature, and battery condition.
Learn more about home shop we have.
Other manuals for 7776
1
This manual suits for next models
2
Table of contents
Other Heath Zenith Accessories manuals
Heath Zenith
Heath Zenith Notifi elite User manual
Heath Zenith
Heath Zenith Wireless Strobe Chime 6144 User manual
Heath Zenith
Heath Zenith 6180 Series User manual
Heath Zenith
Heath Zenith 5210 User manual
Heath Zenith
Heath Zenith Decorative Wireless Chime 6180 User manual
Heath Zenith
Heath Zenith 29 User manual
Heath Zenith
Heath Zenith 7750 User manual
Heath Zenith
Heath Zenith Hardwired Mechanical Chime 598-1112-05 User manual
Heath Zenith
Heath Zenith InTune MP3 Door Chime User manual
Heath Zenith
Heath Zenith Single Entrance Chime 23/M User manual
Heath Zenith
Heath Zenith 6168 User manual
Heath Zenith
Heath Zenith 5316 User manual
Heath Zenith
Heath Zenith 598-1143-01 User manual
Heath Zenith
Heath Zenith 7306 User manual
Heath Zenith
Heath Zenith DualBrite User manual
Heath Zenith
Heath Zenith 7307 User manual
Heath Zenith
Heath Zenith 6168 User manual
Heath Zenith
Heath Zenith 7762 User manual
Heath Zenith
Heath Zenith 5838 User manual
Heath Zenith
Heath Zenith Wireless Push Button Accessory SL-6190... User manual
