Heath Zenith 7750 User manual

This chime requires 2 “C” alkaline batteries (not included). In typical use,

alkaline batteries will last up to one year.

Wireless Chime

Figure 2

Figure 3

Figure 1

WARNING: To prevent possible

SERIOUS INJURY or DEATH:

• NEVER allow small children near

batteries.

• If battery is swallowed, immediately

notify doctor.

This package includes (Style of door sensor and chime may vary from illustration):

1. Remove orange battery tab from push

button. Remove back of case by pushing in

tab on bottom with a small screwdriver (see

Figure 1). Remove orange battery tab.

2. Open chime case. Press in catch on bottom

of chime and lift the case open (see Figure 2).

3. Install 2 alkaline “C” batteries. Make sure

batteries are oriented properly (see Figure 3).

4. Test range. Temporarily position chime and

push button where you want them mounted.

Press push button to verify chime and push

button work properly. If chime does not sound,

see Troubleshooting.

Model

Wireless

chime

Wireless push

button

Hardware

pack

7750 ✔ ✔ ✔

Type “C”

SYNC:

HOLD 3 SEC

RESET:

HOLD 10 SEC

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

5. Mount push button. Use either screws or

double sided tape to mount push button.

• Screw Mounting: To mount with screws,

remove back of case by pushing in tab

on bottom with a small screwdriver (see

Figure 1). Note: Remove material in screw

holes (if needed) before mounting with

screws. Attach back of case to door jamb

or wall (see Figure 4). Snap front of push

button on.

• Tape Mounting: When attaching push but-

ton using double sided tape, make sure the

surface of the door jamb or wall is clean.

6. Mount chime. Determine mounting location.

• Drill 7/32" diameter pilot hole for wall anchor.

•

Mount keyhole screw to wall leaving about

1/8" (3 mm) of the screw threads exposed.

• Using keyhole on back of chime base, hang

base on screw (see Figure 5).

• Note: For additional mounting security, re-

peat the above steps to install two additional

screws through the other two holes in the

chime back.

7. Snap chime cover onto chime base. Align

top edge of case with top of back plate. Rotate

bottom of case toward back plate and snap

into position.

Figure 4

Figure 5

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

Inside Push Button

Tune Settings

Push Button Tune

Jumper - ON Ding

Jumper - OFF Ding-Dong

Tune Setting Table

The chime has different selectable tunes: Ding

(one note tune) or Ding-Dong (two note tune).

The factory setting is for the Ding-Dong tune.This

tune can be changed by following the instructions

in the Tune Setting Table.

Note: All chime models are designed to work with

up to 5 push buttons (sold separately).All chimes

are designed to play only two different tunes no

matter how many push buttons are used.

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

Troubleshooting

1. PROBLEM: Chime does not sound.

A. POSSIBLE CAUSE: Batteries not installed correctly.

A. CORRECTIVE ACTION: Make sure batteries are installed according to

the diagram inside the push button and chime.

B. POSSIBLE CAUSE: Batteries are dead.

B. CORRECTIVE ACTION: Check charge of push button and chime bat-

teries and replace if necessary.

C. POSSIBLE CAUSE: Push button and chime are not synced.

C. CORRECTIVE ACTION: Sync the push button and chime.

• Press and hold the button on the chime until the chime sounds a

“Beep-Beep”.

• Press the push button within 30 seconds. The chime will sound a

“Beep-Beep” tone to indicate the push button is synced.

• Press the push button to ensure operation.

2. PROBLEM: Batteries seem okay, but the chime does not work after instal-

lation.

A. POSSIBLE CAUSE: Chime or push button is mounted on metal or near

metal studs. Note: Metal reduces transmission range.

A. CORRECTIVE ACTION: Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims

to move chime or push button away from metal surface.

B. POSSIBLE CAUSE: Chime is mounted near concrete ﬂoor or wall.Note:

Concrete may reduce range.

B. CORRECTIVE ACTION: Move chime away from concrete surface.

C. POSSIBLE CAUSE: Chime and push button are installed too far apart.

C. CORRECTIVE ACTION: Locate chime closer to push button.

3. PROBLEM: Chime sounds when not intended (false triggers).

POSSIBLE CAUSE: Chime is receiving interference from another wire-

less device.

CORRECTIVE ACTION: Reset chime and push button.

• Remove push button batteries. Wait 30 seconds.

• Press and hold the push button for 10 to 15 seconds within 60 seconds

after installing battery into the push button.

• Press and hold the button on the chime until the chime sounds a

“Beep-Beep-Beep-Beep”.

• To re-sync the push button and chime, press and hold the button on

the chime until the chime sounds a “Beep-Beep”.

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

• Press the push button within 30 seconds. The chime will sound a

“Beep-Beep” tone to indicate the push button is synced.

• Press the push button to ensure operation.

Note: The push button and chime come synced from the factory. The range of

the wireless chime can vary with location, temperature, and battery condition.

Please contact us for assistance

before returning product to the

store or to HeathCo LLC.

If you experience a problem, follow

this guide.You may also contact us be-

tween 8:00 AM to 5:00 PM CST (M-F).

When contacting Technical Service,

please include the following informa-

tion: Name, Street Address, Daytime

Phone Number, Email Address, Model

Number, Date of Purchase, Place of

Purchase, Product Issue, and DATED

SALES RECEIPT FOR WARRANTY

REQUESTS.

Technical Service

No Service Parts Available for this

Product

HeathCo LLC

2445 Nashville Road

Bowling Green, KY 42101, USA

ATTN: Technical Service

Internet: www.hzsupport.com

Phone:1-800-858-8501 (English Only)

Fax: 1-800-846-8500

Regulatory Information

This device complies with Part 15 of the FCC Rules and RSS-210 of Industry

Canada. Operation is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

The user is cautioned that changes or modiﬁcations not expressly approved by

the party responsible for regulatory compliance could void the user’s authority

to operate the equipment.

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501

HeathCo LLC reserves the right to discontinue and to change speciﬁcations

at any time without notice without incurring any obligation to incorporate new

features in previously sold products.

ONE YEAR LIMITED WARRANTY

This is a “Limited Warranty” which gives you speciﬁc legal rights. You

may also have other rights which vary from state to state or province

to province.

For a period of one year from the date of purchase, any malfunction

caused by factory defective parts or workmanship will be corrected at

no charge to you.

Not Covered - Repair service, adjustment and calibration due to misuse,

abuse or negligence, light bulbs, batteries, and other expendable items are

not covered by this warranty. Unauthorized service or modiﬁcation of the

product or of any furnished component will void this warranty in its entirety.

This warranty does not include reimbursement for inconvenience, installation,

setup time, loss of use, unauthorized service, or return shipping charges.

This warranty covers only HeathCo LLC assembled products and is not

extended to other equipment and components that a customer uses in

conjunction with our products.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRAN-

TIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRE-

SENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE

PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND

SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES.

REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE

CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART

OF HEATHCO LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY

LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEE-

ABLE. Some states or provinces do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation or exclusion

may not apply to you.

Please keep your dated sales receipt, it is required for all warranty

requests.

Vídeos prácticos – www.hzsupport.com Respuestas prácticas – 1-800-858-8501

Campana inalámbrica

Esta campana requiere 2 pilas alcalinas tipo “C” (no incluidas). Con un

uso normal, las pilas alcalinas durarán hasta 1 año.

Este paquete tiene (El estilo del pulsador y de la campana puede variar de

la ilustración):

1. Retire la pestaña naranja de la batería del

botón pulsador. Extraer la parte posterior de

la caja presionando la aleta en el botón con

un destornillador pequeño (vea la Figura 1).

Quite la aleta anaranjada de la batería.

2. Abra la caja de la campana. Presione el

seguro, en la parte inferior de la campana, y

levante la caja (vea la Figura 2).

3. Coloque las 2 pilas alkalinas “C”. Asegú-

rese de que estén correctamente colocadas

(vea la Figura 3).

4. Pruebe el alcance. Ponga provisionalmente

la campana y el pulsador en la posición donde

los quiera instalar. Presione el pulsador para

veriﬁcar que la campanay el pulsador funcio-

nen apropiadamente.Si la campana no suena,

vea Análisis de Averías.

ADVERTENCIA: Para prevenir una

posible LESIÓN SERIA o LA MUERTE:

• NUNCA deje que los niños estén cerca

de las baterías.

• Si se traga una batería, notiﬁque inme-

diatamente al doctor.

Figura 2

Figura 3

Figura 1

Modelo

Campana

inalámbrica

Pulsador

inalámbrico

Paquete de

ferretería

7750 ✔ ✔ ✔

Type “C”

SYNC:

HOLD 3 SEC

RESET:

HOLD 10 SEC

Vídeos prácticos – www.hzsupport.com Respuestas prácticas – 1-800-858-8501

5. Monte el pulsador. Use ya sean tornillos o

cinta adhesiva por ambas caras para instalar

el pulsador.

• Montaje con tornillos: Para montar con

tornillos, quite la parte de atrás de la caja

empujando hacia adentro la lengüeta de

abajo con un destornillador pequeño y

girando la cuchilla (vea la Figura 1). Nota:

Quite la suciedad de los orificios para

tornillos (si es necesario) antes de poner

los tornillos. Coloque la parte de atrás de

la caja contra la jamba o la pared (vea la

Figura 4). Encaje a presión la parte frontal

del pulsador.

• Montaje con cinta adhesiva: Cuando

ﬁje el pulsador usando cinta adhesiva por

ambas caras, asegúrese que la superﬁcie

de la pared o la del batiente de la puerta

estén limpias.

6. Monte la campana. Determine el sitio para

el montaje.

• Perfore un agujero piloto de 5.5 mm (7/32

pulgadas) de diámetro para el ancla de

pared.

• Coloque el tornillo del oriﬁcio de alineación

en la pared dejando 3 mm (1/8 de pulgada)

de la rosca del tornillo sin apretar (vea la

Figura 5).

• Usando este oriﬁcio de alineación de la

parte posterior de la base de la campana,

cuelgue la base en el tornillo.

• Nota: Para una seguridad adicional en el

montaje, repita los pasos anteriores para

instalar dos tornillos adicionales a través

de los otros dos agujeros en el reverso del

timbre.

7. Inserte la cubierta de la campanilla en

la base de la campanilla. Alinee el borde

superior de la caja con la parte superior de la

placa de atrás.Gire la parte inferior de la caja

hacia la placa de atrás y asiéntela a presión

en su sitio.

Figura 4

Figura 5

Vídeos prácticos – www.hzsupport.com Respuestas prácticas – 1-800-858-8501

Botón pulsador Ajustes

Puente: ENCENDIDO Ding

Puente: APAGADO Ding-Dong

Tabla de programación de melodías

Dentro del Pulsador

Programación del tono

La campanilla tiene diferentes melodías que

se pueden seleccionar: Ding (melodía de una

nota) o Ding-Dong (melodía de dos notas). La

calibración de fábrica es el tono Ding-Dong. Esta

melodía se puede cambiar siguiendo las instruc-

ciones de la Tabla de Programación de Melodías.

Nota: Todos los modelos de campanillas están

diseñados para trabajar hasta con 5 botones

pulsadores (se venden por separado). Todas

las campanillas están diseñadas para reproducir

solo dos melodías diferentes, sin importar cuán-

tos botones pulsadores se utilicen.

Vídeos prácticos – www.hzsupport.com Respuestas prácticas – 1-800-858-8501

Análisis de Averías

1. PROBLEMA: La campanilla no suena.

A. CAUSA POSIBLE: Las baterías no están bien instaladas.

A. ACCIÓN CORRECTIVA: Asegúrese de que las baterías estén instaladas

de acuerdo con el diagrama ubicado dentro del botón pulsador y de la

campanilla.

B. CAUSA POSIBLE: Las baterías se acabaron.

B. ACCIÓN CORRECTIVA: Revise la carga de las baterías del botón

pulsador y de la campanilla y reemplácelas si es necesario.

C. CAUSA POSIBLE: El botón pulsador y la campanilla no están sincroni-

zados.

C. ACCIÓN CORRECTIVA: Sincronice el botón pulsador y la campanilla.

• Mantenga presionado el botón en la campanilla hasta escuchar un

“bip-bip”.

• Presione el botón pulsador durante 30 segundos. Cuando el botón

pulsador esté sincronizado, la campanilla hará un “bip-bip”.

• Presione el botón pulsador para asegurar el funcionamiento.

2. PROBLEMA: Las baterías parecen estar bien pero la campanilla no funciona

después de la instalación.

A. CAUSA POSIBLE: La campanilla o el botón pulsador están montados

sobre metal o cerca de montantes de metal. Nota: El metal reduce el

alcance de transmisión.

A. ACCIÓN CORRECTIVA: Use calzas de madera de 6 a 13 mm (1/4 a

1/2 pulg.) para sacar la campanilla o el botón pulsador de la superﬁcie

de metal.

B. CAUSA POSIBLE: La campanilla está montada cerca de un piso o pared

de concreto. Nota: El concreto puede reducir el alcance.

B. ACCIÓN CORRECTIVA: Aleje la campanilla de la superﬁcie de concreto.

C. CAUSA POSIBLE: La campanilla y el botón pulsador están instalados

demasiado alejados.

C. ACCIÓN CORRECTIVA: Ubique la campanilla más cerca del botón

pulsador.

Continúa

Table of contents

Languages:

Other Heath Zenith Accessories manuals

Heath Zenith

Heath Zenith 595-5707-06 User manual

Heath Zenith

Heath Zenith Decorative Wireless Chime 6180 User manual

Heath Zenith

Heath Zenith Notifi Elite User manual

Heath Zenith

Heath Zenith Wireless Christmas Chime 598-1127-03 User manual

Heath Zenith

Heath Zenith 6180 Series User manual

Heath Zenith

Heath Zenith Notifi elite User manual

Heath Zenith

Heath Zenith DualBrite User manual

Heath Zenith

Heath Zenith 7868 User manual

Heath Zenith

Heath Zenith 121AC User manual

Heath Zenith

Heath Zenith Wireless Dual Push Button Accessory SL-6200 User manual

Heath Zenith

Heath Zenith Motion Sensing 3-Way Wall Switch 6107 User manual

Heath Zenith

Heath Zenith 29 User manual

Heath Zenith

Heath Zenith DualBrite Replacement Sensor Head 2LBN3 Service manual

Heath Zenith

Heath Zenith SL-7464-03 User manual

Heath Zenith

Heath Zenith 5316 User manual

Heath Zenith

Heath Zenith Wireless Strobe Chime 6144 User manual

Heath Zenith

Heath Zenith Dual Brite SL-5597 User manual

Heath Zenith

Heath Zenith Notif User manual

Heath Zenith

Heath Zenith Replacement Motion Sensor SL-5407 User manual

Heath Zenith

Heath Zenith SECUR360 9600 User manual

Heath Zenith

Heath Zenith Decorative Wireless Chime 598-1000-07 User manual

Heath Zenith

Heath Zenith Replacement Motion Sensor SH-5407 User manual

Heath Zenith

Heath Zenith 6168 User manual

Heath Zenith

Heath Zenith SL-6200 User manual

Popular Accessories manuals by other brands

Hillco

Hillco 2810 Operator's manual

Siemens

Siemens QSA2700D Basic documentation

Contours

Contours ZY024 manual

Saivod

Saivod VS621 manual

Virtuox

Virtuox VirtuCLEAN 2.0 user manual

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS user manual

Z-Wave

Z-Wave HSD-200Z user manual

turck

turck FMX-IM-2UPLI63FX quick start guide

Decagon Devices

Decagon Devices 10HS manual

UPPAbaby

UPPAbaby Cup Holder user manual

Elko

Elko SmartSensor Leakage Wireless manual

Grizzly

Grizzly H8371 instructions

Panasonic

Panasonic HG-T Series user manual

IFM Electronic

IFM Electronic Efector 250 Series Brief instructions

DigiDesign

DigiDesign 888/24 I/O installation guide

PROZIS

PROZIS QUAY user manual

patagonia

patagonia PSI Vest user manual

SFC Energy

SFC Energy EFOY GO! manual