HAMPTON BAY Colonial Bamboo User manual

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

Hampton Bay Lifetime Limited Warranty

The retailer warrants the fan motor to be free from defects in workmanship and material present at

time of shipment from the factory for a lifetime after the date of purchase by the original purchaser.

The retailer also warrants that all other fan parts, excluding any glass or plexiglass blades, to be free

from defects in workmanship and material at the time of shipment from the factory for a period of

one year after the date of purchase by the original purchaser. We agree to correct such defects

without charge or at our option replace with a comparable or superior model if the product is

returned to the retailer. To obtain warranty service, you must present a copy of the receipt as proof

of purchase. All costs of removing and reinstalling the product are your responsibility. Damage to

any part such as by accident or misuse or improper installation or by affixing any accessories, is not

covered by this warranty. Because of varying climatic conditions in the United States this warranty

does not cover any changes in brass finish, including rusting, pitting, corroding, tarnishing or

peeling. Brass finishes of this type give their longest useful life when protected from varying

weather conditions. A certain amount of wobble is normal and should not be considered a defect.

Servicing performed by unauthorized persons shall render the warranty invalid. There is no other

express warranty. The retailer hereby disclaims any and all warranties, including but not

limited to. Those of merchantability and fitness for a particular purpose to the extent

permitted by law. The duration of any implied warranty which cannot be disclaimed is limited to

the time period as specified in the express warranty. Some states do not allow limitation on how

long an implied warranty lasts, so the above limitation may not apply to you. The retailer shall not

be liable for incidental, consequential, or special damages arising out of or in connection with

product use or performance except as may otherwise be accorded by law. Some states do not

allow the exclusion of incidental or consequential damages, so the above exclusion or limitation may

not apply to you. This warranty gives specific legal rights, and you may also have other rights which

vary from state to state. This warranty supersedes all prior warranties.

Lifetime Limited Warranty

278-050

11289

792145353157

Table of Contents

SAFETY RULES..............................................................................................................................

UNPACKING YOUR FAN.............................................................................................................

INSTALLING YOUR FAN.............................................................................................................

INSTALLING THE LIGHT KIT...................................................................................................

OPERATING YOUR FAN.............................................................................................................

CARE OF YOUR FAN..................................................................................................................

TROUBLESHOOTING................................................................................................................

SPECIFICATIONS........................................................................................................................

1. To reduce the risk of electric shock, insure electricity has been turned

off at the circuit breaker or fuse box before beginning.

2. All wiring must be in accordance with the National Electrical Code and

local electrical codes. Electrical installation should be performed by a

qualified licensed electrician.

3. WARNING: To reduce the risk of electrical shock and fire, do not use

this fan with any solid-state fan speed control device.

4. WARNING: To reduce the risk of fire, electric shock, or personal

injury, mount to outlet box marked "Acceptable for Fan Support of

22.7 kg (50 lbs.) Or Less" and use mounting screws provided with the

outlet box. Most outlet boxes commonly used for the support of light

fixtures are not acceptable for fan support and may need to be replaced.

consult a qualified electrician if in doubt.

5. The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 50 pounds. Use only UL

Listed outlet boxes marked FOR FAN SUPPORT.

6. The fan must be mounted with a minimum of 7 feet clearance from the

trailing edge of the blades to the floor.

7. Avoid placing objects in the path of the blades.

8. Reverse the fan while the motor is on any speeds.

9. To avoid personal injury or damage to the fan and other items, be

cautious when working around or cleaning the fan.

10. Do not use water or detergents when cleaning the fan or fan blades. A

dry dust cloth or lightly dampened cloth will be suitable for most

cleaning.

11. After marking electrical connections, spliced conductors should be

turned upward and pushed carefully up into outlet box. The wires

should be spread apart with the grounded conductor and the

equipment-grounding conductor on one side of the outlet box.

12. Electrical diagrams are reference only. Light kit that are not packed

with the fan must be UL Listed and marked suitable for use with the

model fan you are installing. Switches must be UL General Use

Switches. Refer to the Instructions packaged with the light kits and

switches for proper assembly.

1. Safety Rules

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND

THE BLADE BRACKETS (ALSO REFERRED TO AS FLANGES)

DURING ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT

OBJECTS IN THE PATH OF THE BLADES.

NOTE

READ AND SAVE ALL INSTRUCTIONS!

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE

FOR FAN SUPPORT.

1. Set of blades (5)

2. Canopy assembly

3. Ball/downrod assembly (1)

& extra downrod (1)

4. Collar cover

5. Fan motor assembly

6. Set of blades brackets (5)

7. Mounting plate

8. Light kit assembly

9. Glsss shade (3)

10. Transmitter + holder + 2 mounting

screws

11. 13 Watt compact fluorescent bulb (3)

12. Extra plastic plug

13. Balancing kit

14. Loose parts bag containing:

a. Blade attachment hardware

(16 screws with fiber washers)

b. Mounting hardware

( 3 plastic wire connectors )

Unpack your fan and check the contents. You should have the following items:

Unpacking Your Fan 2.

WARNING

DO NOT INSTALL OR USE FAN IF ANY

PART IS DAMAGED OR MISSING.

CALL TOLL FREE 1-877-902-5588.

713

SET

TEMP

FAN AUT O

LOWLOW

FANAUTO FOR/ REV

LIGHTD ELAYTIMER

TIMEP./SET

HOUR

HIGH

ROOM

TEMP

72 74

Tools Required

Phillips screwdriver, straight slot screwdriver,

adjustable wrench, step ladder, and wire

cutters.

Mounting Options

Heavy duty ceiling fan rated outlet box is

required (at least 50 lbs). Do not use regular

outlet box (metal or plastic).

Figures 1,2 and 3 are examples of different

ways to mount the outlet box.

3. Installing Your Fan

Figure 1

Figure 2

Figure 3

Note: You may need a longer downrod to

maintain proper blade clearance when

installing on a steep, sloped ceiling.

Heavy duty

outlet box for fan

Angled ceiling

maximum

25°angle

Recessed

outlet box

Provide strong support

Mounting bracket

opening must be

toward the top

Heavy duty fan brace

Heavy duty

outlet box for fan

Hanging the Fan

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly.

Step 1. Remove the decorative canopy bottom

cover from the canopy by turning the cover

counter clockwise.(Fig. 4)

Step 2. Remove the hanger bracket from the

canopy by loosening the two screws on the bottom

of the hanging bracket a half turn from the screw

head and turning the canopy counter clockwise.

(Fig. 4)

Step 3. Remove the hanger pin, lock pin and set

screws from the top of the motor assembly. (Fig. 5)

Step 4. Route wires exiting from the top of the fan

motor through the collar cover, canopy cover,

canopy and then through the ball/downrod. (Fig. 5)

Step 5. Align the holes at the bottom of the

downrod with the holes in the collar on top of the

motor housing (Fig.5). Carefully insert the hanger

pin through the holes in the collar and downrod.

CHANGING THE DOWNROD (OPTIONAL)

NOTE: Your fan comes with a 4" downrod

attached to the hanger ball. In addition you have

been provided with a 6" downrod to use if desired.

If you choose to use the 6" downrod, perform the

following steps:

1. Remove the hanger ball from the downrod by

loosening the set screw at the top of the downrod

which holds the hanger ball to the downrod.

2. Slide the hanger ball down the downrod and

remove the support pin.

3. Insert the support pin in the holes at the top of

the 6" downrod and slide the hanger ball up the 6"

downrod. Make sure the support pin is properly

seated in the grooves in the top of the hanger ball.

4. Tighten the set screws firmly.

Step 6. Tighten two set screws on top of the fan

motor firmly (Figure 5)

Step 7. Install the hanger bracket to the outlet

box; be sure to align the holes in the hanger

bracket with the post holes in the outlet box and

secure with screws and washers provided by the

outlet box.(Figure 6)

Step 8. Hanging the assembled fan onto the

mounting bracket, place the downrod ball into the

mounting bracket. Rotate fan until the slot of the

downrod ball locks into the tab of the mounting

bracket. (Figure 7)

Step 9. Secure the safety cable to the building

structure as shown in Fig. 7

Step 10. Connecting the wires (see making the

electrical connections)

WARNING

FAILURE TO PROPERLY INSTALL LOCKING

PIN AS NOTED IN STEP 5 COULD RESULT IN

FAN LOOSENING AND POSSIBLY FALLING.

Be careful not to jam the pin against the wiring

inside the downrod. Insert the locking pin through

the hole near the end of the hanger pin until it

snaps into its locked position, as noted in the

circle inset of Fig. 5.

CAUTION

REMOVE THE 5 SCREWS FROM THE

MOTOR SUPPORT PLATE, DISCARD THE 5

SCREWS AND MOTOR SUPPORT PLATE.

Pin in locked

position

Motor collar

Motor wires

Ball/downrod

assembly

Ceiling

canopy

Tighten screws

firmly

Figure 5

Making the Electrical

Connections

Remember to disconnect the power.

Follow the steps below to connect the fan to your

household wiring. Use the wire connecting nuts

supplied with your fan. Secure the connectors

with electrical tape. Make sure there are no loose

strands or connections.

Step 1 Connect the fan supply (black) wire to the

black household supply wire as shown in Figure

Step 2 Connect the neutral fan (white) wire to the

white neutral household wire. (Fig. 8)

Step 3 Connect the fan ground wire (green) to

the household ground wire.(Fig. 8)

Step 4 After connecting the wires, spread them

apart so that the green and white wires are on one

side of the outlet box and the black wires are on

the other side.

Step 5 Turn the connecting nuts upward and push

the wiring into the outlet box.

Figure 4

Figure 6

Figure 7

Hanger pin

Locking pin Collar cover

Canopy

cover

Ceiling

mounting

plate

Ceiling

canopy

Canopy

cover

Hanger

bracket

AC Wires

Screws provided

by the outlet box

Hook

Washers

Hanger

bracket

Posts in the

outlet box

UL Listed

electrial

box

Safety cable

Finishing the Installation

Step 1. Tuck connections neatly into ceiling outlet

box.

Step 2. Slide the canopy up to ceiling and over

the 2 screws on hanger bracket. Rotate canopy

clockwise, next, while holding the canopy with

one hand, slide the canopy cover over the screws

and rotate clockwise until tight. Note: adjust the

canopy screws as necessary until the canopy and

canopy cover are snug. (Fig. 9)

Figure 8

SUPPLY CIRCUIT

BLACK BLACK

Ground

Conductor

Outlet Box

Green

Ground

Lead

Ground to

Downrod

GREEN

WHITE WHITE

WARNING

MAKE SURE TAB AT BOTTOM OF HANGER

BRACKET IS HANGER PROPERLY SEATED IN

GROOVE OF HANGER BALL BEFOREATTACHING

CANOPY TO BRACKET. FAILURE TO PROPERLY

SEAT TAB IN GROOVE COULD CAUSE DAMAGE

TO ELECTRICAL WIRING.

Figure 9

hanger

bracket

Outlet box

Screws

Canoby

Canoby cover

Attaching the Fan Blades

Step 1 Attach the blades to the blade arms using

three screws with fiber washers as shown in

Figure 10. Start a screw into the arm, do not

tighten. Repeat for the 2 remaining screws and

washers.

Step 2 Tighten each screw securely starting with

the center screw. Make sure the blade is straight.

Step 3: Fasten the blade assemblies to the motor

housing by lining up the slots of the blade arms

with the tabs on the motor housing, then tighten

the two screws and washers already installed in

the blade arms. (Figure 11)

Figure 11

Figure 10

Blade arm

Blade

Screws

with fiber

washer Motor

Blade arm

Slot

Tab

Installing the Light Kit 8.

NOTE: Before starting installation, disconnect

the power by turning off the circuit breaker or

removing the fuse at fuse box.Turning power off

using the fan switch is not sufficient to prevent

electric shock.

1. Remove the 1 of 3 screws from themounting

ring and keep it for future use.Loosen the other

2 screws. (Do not remove)

2. Place the key holes on the switch housing

over the 2 screws previously loosened from the

mounting ring, turn the switch housing until it

locks in place at the narrow section of the key

holes. Secure by tightening the 2 screws

previously loosened and the one previously

removed. (Figure 12)

3. Make the wire connections: Connect the 9-pin

plug from the fan to the 9-pin plug from the

light kit assembly.

4. Carefully push all wires back into the switch

housing. Attach the light kit assembly to the

mounting plate with 3 screws provided.

5. Mount the glass shades to the light fixture by

unscrewing partway the thumbscrews on the

glass holders, inserting the glass, then gently

tightening the thumbscrews by hand evenly to

the glass. DO NOT OVER TIGHTEN.

6. With the power off, insert the light compact

fluorescent bulbs × 3 (included) into the light

kit sockets. Max. 13 watts.

Fan Without Light Kit

1. Disassemble the switch box from the light kit

by loosing the two plug-in wire connectors,

you can keep the light kit for future use.

(Figure 13)

2. Attach the plastic plug to the switch box.

3. Remove the screws from the mounting ring

under the fan motor, Raise the switch box to the

mounting ring until the holes in switch box and

mounting ring line up. Reinsert the screws to

secure in place.

7. Restore power and your light kit is ready for

operation.

Mounting plate

Connector plugs

Glass shade

Bulbs

Thumb

screws

Light kit

assembly

Screws

Mounting ring

Figure 12 Figure 13

Switch housing

Lock washer

Nut

Light kit

Other manuals for Colonial Bamboo

This manual suits for next models

Table of contents

Other HAMPTON BAY Fan manuals

HAMPTON BAY

HAMPTON BAY YG529-WH User manual

HAMPTON BAY

HAMPTON BAY 290-286 User manual

HAMPTON BAY

HAMPTON BAY CLARET User manual

HAMPTON BAY

HAMPTON BAY 394-243 User manual

HAMPTON BAY

HAMPTON BAY Minuet III AG806C-EB User manual

HAMPTON BAY

HAMPTON BAY ST. DAVID 51344 User manual

HAMPTON BAY

HAMPTON BAY 296 065 User manual

HAMPTON BAY

HAMPTON BAY MENA 92404 User manual

HAMPTON BAY

HAMPTON BAY ETRIS 52 User manual

HAMPTON BAY

HAMPTON BAY EDELWEISS User manual

HAMPTON BAY

HAMPTON BAY RENWICK 656 416 User manual

HAMPTON BAY

HAMPTON BAY HAWKINS YG204I-TB-D User manual

HAMPTON BAY

HAMPTON BAY ASHBURTON YG593-WH User manual

HAMPTON BAY

HAMPTON BAY Middleton 42 inch User manual

HAMPTON BAY

HAMPTON BAY YG115-MWH User manual

HAMPTON BAY

HAMPTON BAY 786-756 User manual

HAMPTON BAY

HAMPTON BAY PENDLETON User manual

HAMPTON BAY

HAMPTON BAY Edgemont 324-848 User manual

HAMPTON BAY

HAMPTON BAY Beverley II 325-475 User manual

HAMPTON BAY

HAMPTON BAY CARROLTON II User manual

HAMPTON BAY

HAMPTON BAY RIVERWALK User manual

HAMPTON BAY

HAMPTON BAY 58919 User manual

HAMPTON BAY

HAMPTON BAY Pendleton 91252 User manual

HAMPTON BAY

HAMPTON BAY 705 114 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual