HAMPTON BAY 290-286 User manual

Lifetime Limited Warranty

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

290-286

219054

718212340219

Hampton Bay Lifetime Motor Warranty

The retailer warrants the fan motor to be free from defects in workmanship and material

present at time of shipment from the factory for a lifetime after the date of purchase by the

original purchaser. The retailer also warrants that all other fan parts, excluding any glass or

plexiglass parts, to be free fromdefects in workmanshipand material at the time of shipment

from the factory for a period of one year after the date of purchase by the original purchaser.

We agree to correct such defects withoutcharge or at our option replace with acomparable or

superior model ifthe product isreturned to the retailer. To obtain warranty service,you must

present a copy of the receipt as proof of purchase. All costs of removing and reinstalling the

product are your responsibility. Damage to any part such as by accident or misuse or

improper installation or by affixing any accessories, is not covered by this warranty.

Because of varying climatic conditions in the United States this warranty does not cover any

changes in brass finish, including rusting, pitting, corroding, tarnishing or peeling. Brass

finishes of this type give their longest useful life when protected from varying weather

conditions. A certain amount of wobble is normal and should not be considered a defect.

Servicing performed by unauthorized persons shall render the warranty invalid. There is no

other express warranty. The retailer hereby disclaims any and all warranties, including

but not limited to. Those of merchantability and fitness for a particular purpose to the

extent permitted by law. The duration of any implied warranty which cannot be disclaimed

is limited to the time period as specified in the express warranty. Some states do not allow

limitation on how long an implied warranty lasts, so the above limitation may not apply to

you. The retailer shall not be liable for incidental, consequential, or special damages

arising out of or in connection with product use or performance except as may

otherwise be accorded by law. Some states do not allow the exclusion of incidental or

consequential damages, so the above exclusion or limitation may not apply to you. This

warranty gives specific legal rights, and you may also have other rights which vary from

state to state. This warranty supersedes all prior warranties.

Table of Contents

SAFETY RULES....................................................................................................

PACKAGE CONTENTS ........................................................................................

INSTALLING YOUR FAN.....................................................................................

HANGING THE FAN.............................................................................................

ELECTRICAL CONNECTIONS ..........................................................................

.........................................................

FINISHING THE INSTALLATION.......................................................................

BLADE INSTALLATION .....................................................................................

.............................................................

.......................................................

OPERATING TRANSMITTER....................................................................

CARE OF YOUR FAN..........................................................................................

TROUBLESHOOTING.......................................................................................

SPECIFICATIONS..............................................................................................

INSTALLING THE WALL TRANSMITTER

INSTALLING THE MOUNTING PLATE

INSTALLING THE LIGHT KITASSEMBLY

THE

1. Before you begin installing the fan, shut power off at the

circuit breaker orthe fuse box.

2. Be cautious! Read all instructions and safety information

before installing your new fan. Review accompanying

assembly diagrams.

3. Make sure that all electrical connections comply with local

codes, ordinances, or National Electrical Codes. Hire a

qualified electrician or consult a do-it-yourself wiring

handbook if you are unfamiliar with installing electrical

wiring.

4. Make sure the installation site you choose allows the fan

blades to rotatewithout any obstructions. Allow a minimum

clearance of 7 feet from the floor and 18 inches from the tip

of the bladesto the wall.

5. If you are mounting the fan to a ceiling outlet box, use U.L.

Listed metal octagonal outlet box marked "Acceptable for

fan support". Secure the box directly to the building

structure. The outlet box and its support must be able to

support the moving weight of the fan (at least 50 lbs.) Do

not use aplastic box.

6. Caution: To reduce the risk of personal injury use only the

screws provided withthe outlet box.

7. If you are mounting the fan to a joist, make sure it is able to

support the movingweight of thefan (at least50 lbs.).

8. After you install the fan, make sure that all mountings are

secured to preventthe fan fromfalling.

1. Safety Rules

9. Do notinsert anything intothe fan bladeswhile the fanis operating.

10. To change the direction of the rotation of the blades the fanmust be in

operation mode.

ATTENTION: The Energy Policy Act of 2005 requires this fan to be

equipped with a 190 watt limiting device. If lamping exceeds 190

watts, the ceilingfan's light kitwill shut off automatically.

NOTE: The important safeguards and instructions appearing in this

manual are not meant to cover all possible conditions and situations that

may occur.It must beunderstood that commonsense, caution andcare are

factors which can not be built into this product. These factors must be

supplied by theperson(s) installing, caringfor and operatingthe unit.

TO REDUCETHE RISK OFFIRE, ELECTRIC SHOCK,OR OTHER PERSONAL

INJURY, MOUNT FAN ONLY TOA U.L. LISTED OUTLETBOX OR SUPPORTING

SYSTEM MARKEDACCEPTABLE FORFAN SUPPORT ANDUSE MOUNTING

SCREWS ANDLOCK WASHERS PROVIDED WITHTHE OUTLET BOX, MOST

OUTLET BOXES COMMONLY USEDFOR THE SUPPORT OF LIGHTING

FIXTURES ARENOT ACCEPTABLE FOR FAN SUPPORTAND NEEDTO BE

REPLACED. CONSULT AQUALIFIED ELECTRICIAN IF IN DOUBT.

TO REDUCETHE RISK OFPERSONAL INJURY,DO NOT BENDTHE BLADE

HOLDERS WHILE INSTALLING, BALANCING THEBLADES, OR CLEANING

THE FAN.DO NOT INSERT FOREIGN OBJECTSBETWEEN ROTATING FAN

BLADES.

TO REDUCETHE RISK OFFIRE OR ELECTRIC SHOCK, DO NOTUSE THIS FAN

WITH ANYSOLID-STATE SPEED CONTROLDEVICE

WARNING

NOTE

READ AND SAVE ALLINSTRUCTIONS!

Unpack your fanand check the contents. You should havethe following items;

1 Fan blades (5)

2. Hanger bracket

3. Canopy

4. Canopy cover

5a. Standard downrod assembly

5b. Minimum-length downrod(for close

to the ceilinginstallation only)

7. Fan motorassembly

8. Blade holders (5)

Coupling cover

9. Blade medallions(5)

10. Mounting plate

11. Lightplate

12. Glass shade

13.

14a. Wall transmitter incl. 2 mounting screws

+ 3

14b. Wall plate w/2mounting screws

15. 50W Halogen bulb (2)

16. Balancing kit

Receiver+6 wire nuts

wire nuts

Package Contents 2.

a. Mounting hardware:

Wire nuts(3)

b. Blade attachmenthardware:

Screws (16)

(16)

c. Blade holderhardware:

Screws with lockwashers (11)

Rubber washers

14b

14a

3. Installing Your Fan

Outlet box

Figure 1

Ceiling

joist

Ceiling

joist

Cross brace

Outlet box

Figure 2

Ceiling joist

or cross brace Parallel

wood brace

Provide strong

support

Recessed

outlet box

Hanger bracket

opening must

be facing up-side

Figure 3

Outlet box

Figure 4

Ceiling

joist

Hanger bar

(optional)

Hanger

bracket

Angled ceiling

maximum

18 angle

Phillips screw driver; slotted screw driver; step-

ladder; wire cutters;electrical tape.

If there isn'tan existing mountingbox, then readthe

following instructions. Disconnect the power by

removing fuses orturning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and building

materials. The outlet box and its support must be

able to fully support the moving weight of the fan

(at least 50 lbs.). Use a UL Listed metal outlet box.

Do not usea plastic outletbox.

Figure 1, 2 and 3 are examples of different ways to

mount the outletbox.

Note: You may need a longer downrod to maintain

proper blade clearance when installing on a steep,

sloped ceiling. Longer downrods are available from

your Hampton Baydealer.

To hang your fan where there is an existing fixture

but no ceilingjoist, you mayneed to install a hanger

bar as shown in Fig. 4 (available at your Hampton

Bay dealer).

Tools Required

Mounting Options

REMEMBER to turn off the power.

Follow the steps below to hang your fan

properly:

Step 1. Secure the hanger bracket to the

ceiling outlet box using screws and

included with your outlet box,

(Fig.5)

Step 2. Loosen the two set screws and

from the

top coupling ofthe motor assembly. (Fig.6)

Step 3. Remove the hanger ball from

downrod assembly by loosening set

screw, removing the cross pin, and sliding

ball off rod. (Fig.7)

Step 4. Carefully feed fan wires up

through the downrod. (Fig. 8) Thread the

rod into the coupling. Next line up holes

and replace lock pin and hitch pin. Tighten

set screws.

Step 5. Slip coupling cover, canopy cover

and canopy onto downrod. (Fig.9)

Carefully reinstall

lock

washers

remove the hitch pin and lock pin

the

hanger ball onto rod

being sure that cross pin is in correct

position, set screws are tighten and wires

are not twisted.

Step 6. Now lift motor assembly into

position and place hanger ball into hanger

bracket. Rotate until the check groove has

dropped into the registration slot and seats

firmly. (Fig. 10) Rod should not rotate if

this is donecorrectly.

Outlet box

Hanger bracket

Cross pin

Hanger

ball

Downrod

Supply

wires

Figure 5

Figure 7 Figure 8

Figure 6 Figure 9

Figure 10

Registration

slot

Downrod

Canopy

Canopy cover

Set screws

Hitch pin

Lock pin

Hitch

pin Lock

Set

screws

Hanger ball

Coupling

*Omit coupling

cover when

downrod

cover

using

the minimum-length

Hanging the Fan 4.

Receiver

Hanger bracket

Figure 11

Figure 12

WARNING: To avoid possible electrical

shock be sure electricity is turned off at the

main fuse orbreaker box beforewiring.

NOTE: The Wall Control units included

with your ceiling fan are equipped with 16

code combinations to prevent possible

interference from or to other remote units.

The dip switches on your Receiver and

Transmitter units have been preset at the

factory, please re-check to make sure the

switches on both units are set to the same

positions. The frequency settings should be

changed only in case of interference or if a

second or more remote controlled ceiling

fans are installed in the same structure. Any

code combination will operate the ceiling

fan and light as long as the Receiver and

Transmitter units are set to the same codes

(Fig. 11)

Step 1. Insert Receiver into Hanger Bracket

with the flat side of the Receiver facing the

ceiling. (Fig. 12)

Step 2. Motor to Receiver Electrical

Connections: Connect the Black wire

from the fan to Black wire marked "TO

MOTOR L". Connect the White wire from

the fan to the White wire marked "TO

MOTOR N" from the receiver. Connect the

Blue wire from the fan to the Blue wire

marked "For Light" from the receiver. Secure

wire connections with the plastic wire nuts

provided. (Fig. 13 and 14)

(Fig. 13 and14)

connectors

Step 3. Receiver to House Supply Wires

Electrical Connections: Connect the WHITE

wire (Neutral) from the outlet box to the

WHITE wire marked "AC in N" from the

receiver. Connect the BLACK wire (Hot)

from the outlet box to the BLACK wire

marked "AC in L" from the receiver. Secure

all wire connections with the plastic wire nuts

provided.

Step 4. If your outlet box has a GROUND

wire (Green orBare Copper) connectthis wire

to the Hanger Ball and Hanger Bracket

Ground wires. If your outlet box does not

have a Ground Wire, then connect the Hanger

Ball and Hanger Bracket Ground Wires

together. Secure wire connection with the

plastic wire nutprovided. (Fig. 13& 14)

After all are made, check to make

sure there are no loose strands. As an

additional precaution wesuggest to secure the

plastic wire connectors to the wires with

electrical tape.

ONON

5. Electrical Connections

Fan

White (neutral)

Green or bare

copper (ground)

White ("AC INN")

White ("to motor N")

Ground

(green)

(Connect to

ground wire on

hanger bracket

if no house

ground wire

exists.)

Outlet box

Black (hot)

Black ("AC INL")

Black ("to motor L")

Receiver

Blue ("for light")

Black (motor)

Figure 13

Figure 14

Wall

control

Black

White

Blue

Ground Green

Green Ground

INPUT

AC120V

AC SUPPLY

WARNING: HOOK UP IN "SERIES ONLY" DO NOT CONNECT THE HOT AND NEUTRAL WIRES OF ELECTRIC

CIRCUIT TO THE TRANSMITTER WALL SWITCH - DAMAGE TO THE SWITCH AND POSSIBLE FIRE COULD

OCCUR.

Step 1. Remove the existingwall plate andswitch from thewall junction box.

Step 2.

Step 3. (Fig. ) Carefully tuck the wire connections inside the junction box. Secure the wall transmitter with the two screws

provided. Attach the wall plate over the wall transmitter and secure with thetwo screws provided.

Make the electrical connections as shown in (Fig. 14). If your outlet box has a ground wire (green or bare copper) connect

the wall transmitter's ground wire to it; otherwise connect the wall transmitter's ground wire directly to one of the screws from the

outlet box.

Figure 15

REMEMBER to Shutthe Power Off at the Circuit Breaker or Fuse Box.

6. Installing the Wall Transmitter

8. Blade Installation

Step 1. Attach the fan blades to the blade

holder and blade medallions using the

screws and rubber washers provided,

tighten screws securely. (Fig. 17)

Step 2. Rotate motor so that the screw holes

are revealed through the opening on

mounting ring. Align motor holes to blade

holders and secure with screws provided,

tighten screws securely. (Fig. 17)

Blade

Blade holder

Screws

Rubber

washers

Blade medallion

Figure 17

9. Installing the

Mounting Plate

Step 1. Remove 1 of the 3 screws from the

mounting ring and loosen the other 2 screws.

(Do not remove)

Step 2. Place the key holes on the mounting

plate over the 2 screws previously loosened

from the mounting ring, turn mounting plate

until it locks in place at the narrow section of

the key holes. Secure by tightening the 2

screws previously loosened and the one

previously removed. (Fig.18)

Figure 18

Mounting plate

Mounting ring

Screws

7. Finishing the

Installation

Step 1. Tuck connections neatly into ceiling

outlet box.

Step 2. Slide the canopy up to ceiling and

over the two crews on hanger bracket. Rotate

canopy clockwise. Next, while holding the

canopy with one hand, slide the canopy

cover over the screws and rotate clockwise

until tight. Note: adjust the canopyscrews as

necessary until the canopy and canopy cover

are snug. (Fig.14)

Figure 16

Canopy

cover

Outlet box

Hanger

bracket

Hanger

ball

Canopy

Table of contents

Other HAMPTON BAY Fan manuals

HAMPTON BAY

HAMPTON BAY CEVA User manual

HAMPTON BAY

HAMPTON BAY Clarington 503 837 User manual

HAMPTON BAY

HAMPTON BAY Landmark Plus User manual

HAMPTON BAY

HAMPTON BAY GLENDALE III AK488-MBK User manual

HAMPTON BAY

HAMPTON BAY Spoleto II Spoleto II User manual

HAMPTON BAY

HAMPTON BAY Rocio User manual

HAMPTON BAY

HAMPTON BAY 91126 User manual

HAMPTON BAY

HAMPTON BAY 52202 User manual

HAMPTON BAY

HAMPTON BAY BPT12-13E User manual

HAMPTON BAY

HAMPTON BAY 42010 User manual

HAMPTON BAY

HAMPTON BAY CORWIN 56050 User manual

HAMPTON BAY

HAMPTON BAY Gazebo II User manual

HAMPTON BAY

HAMPTON BAY 411-969 User manual

HAMPTON BAY

HAMPTON BAY YG204D-BN User manual

HAMPTON BAY

HAMPTON BAY Gazebo 473-131 User manual

HAMPTON BAY

HAMPTON BAY HAWKINS II Series User manual

HAMPTON BAY

HAMPTON BAY 68" Enchantment User manual

HAMPTON BAY

HAMPTON BAY ASHBURTON YG593-WH User manual

HAMPTON BAY

HAMPTON BAY Northport 178-047 User manual

HAMPTON BAY

HAMPTON BAY Windward IV User manual

HAMPTON BAY

HAMPTON BAY Beverley II 325-475 User manual

HAMPTON BAY

HAMPTON BAY 45071-050 User manual

HAMPTON BAY

HAMPTON BAY DANETREE N243B-BN User manual

HAMPTON BAY

HAMPTON BAY Gazebo II Plus User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual