HAMPTON BAY 705 114 User manual

Cohutta

in Ceiling Fan

Owner’s Manual

Ventilador de Techo de m

Manual del Propietario

Cohutta

1,32

705 114

Cohutta by Hampton Bay

Cohutta

Ceiling Fan by Hampton Bay

Date Purchased

Store Purchased

ETL

Model No.

Serial No.

Vendor No.

UPC

Table of Contents

Safety Rules . . . . . . . . . . . . . . . . . . . . 1

Unpacking Y

our

Fan . . . . . . . . . . . . . . 2

Installing Y

our

Fan . . . . . . . . . . . . . . . 3

Installing the Light Kit. . . . . . . . . . . . . 8

Care of Y

our

Fan . . . . . . . . . . . . . . . . 10

Troubleshooting . . . . . . . . . . . . . . . . . 10

Specifications . . . . . . . . . . . . . . . . . . 11

Warranty Information . . . . . . . . . . . . 12

222875

Thank you for purchasing our ceiling fan. This product has been

manufactured with the highest standards of safety and quality.

CF652KR-CHT

845952000216

Safety Rules - Read and Save These Instructions

WARNING

ATTENTION

To reduce the risk of electric shock, insure electricity has been

turned off at the circuit breaker or fuse box before beginning.

All wiring must be in accordance with the National Electrical

Code “ANSI/NFPA 70-1999” and local electrical codes. Electrical

installation should be performed by a qualified licensed

electrician.

WARNING: To reduce the risk of electrical shock or fire, do not

use this fan with any solid-state fan speed control device. It will

permanently damage the electronic circuitry.

CAUTION: To reduce the risk of personal injury, use only the

screws provided with the outlet box.

The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 35 pounds. Use only

UL Listed outlet boxes marked “FOR FAN SUPPORT”.

The fan must be mounted with a minimum of 7 feet clearance from

the trailing edge of the blades to the floor.

Avoid placing objects in path of the blades.

To avoid personal injury or damage to the fan and other items, be

cautious when working around or cleaning the fan.

Do not use water or detergents when cleaning the fan or fan blades.

A dry dust cloth or lightly dampened cloth will be suitable for most

cleaning.

After making electrical connections, spliced conductors should be

turned upward and pushed carefully up into outlet box. The wires

should be spread apart with the grounded conductor and the

equipment-grounding conductor on one side of the outlet box and

ungrounded conductor on the other side of the outlet box.

All set screws must be checked and retightened where necessary

before installation.

10.

11.

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE ARMS (ALSO REFERRED TO AS FLANGES), WHEN

INSTALLING THE BRACKETS, BALANCING THE BLADES OR

CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS IN –

BETWEEN ROTATING FAN BLADES.

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR

FAN SUPPORT WITH THE SCREWS PROVIDED WITH THE OUTLET

BOX.

FAN INCLUDES A 190W LIMITER TO COMPLY WITH THE

DEPARTMENT OF ENERGY 2009 REGULATION. LAMPING THIS

PRODUCT OVER 190W WILL CAUSE THIS FAN TO NOT LIGHT.

PLEASE USE BULBS WITH A TOTAL WATTAGE UNDER THE 190W

REGULATION.

Unpacking Your Fan Unpack your fan and check the contents. You should have the following items:

9. Compartment cover (1)

10. Light fitter (1)

11. Small fan blades (3)

12. Receiver(1)

13. Transmitter (1)

13A. holder with 2 mounting screws Transmitter

14. Bulb(1)

1. Fan

2. Hanger bracket(1)

3. Canopy (1)

4. Canopy cover(1)

5. Downrod assembly (1)

6. Coupling cover(1)

7. Fan motor assembly(1)

8. Blade holders (3 )

blades (3) 15. Loose parts bag containing:

a. Blade hardware

(10 screws ( )and paper washers)6 mm

b. Small fan blade attachment hardware

attachment

Set of b hardware (1 screw) lade holders

Balancing kit (1)

(10 screws ( )and paper 13 mm washers)

13A

WARNING

DO NOT INSTALL OR USE FAN

IF ANY PART IS DAMAGED OR MISSING.

CALL TOLL FREE 1-877-262-7511

Installing Your Fan

WARNING

Outlet Box

Figure 2

Figure 1

Ceiling

Mounting

Plate

Provide Strong

Support

Recessed

Outlet Box

Figure 3

Figure 4

Tools Required

Mounting Options

Phillips screwdriver, straight slot

screwdriver, step ladder and wire cutters.

If there isn't an existing UL listed mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 35 lbs). Do

not use plastic outlet boxes.

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT FAN

ONLY TO AN OULET BOX MARKED ACCEPT-

ABLE FOR FAN SUPPORT AND USE THE

MOUNTING SCREWS PROVIDED WITH THE

OULET BOX. OUTLET BOX COMMONLY USED

FOR THE SUPPORT OF LIGHTING FIXTURE

MAY NOT BE ACCEPTABLE FOR FAN SUPPORT

AND MAY NEED TO BE REPLACED. CONSULT A

QUALIFIED ELECTRICIAN IF IN DOUBT.

Figures 1~3 are examples of different ways to

mount the outlet box.

Note: You may need a longer downrod to

maintain proper blade clearance when

installing on a steep, sloped ceiling. The

maximum angle allowable is 18°. If the

canopy touches downrod, remove the

decorative canopy bottom cover and turn the

canopy 180° before attaching the canopy to

the mounting plate.

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4

(available at any Home Depot store).

Hanging the Fan

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly:

4. Carefully feed fan wires up through the

downrod. (Figure 8) Thread the rod into the

coupling. Next, line up holes and replace lock

pin and hitch pin. Tighten set screws.

5. Slip coupling cover, canopy cover and

canopy onto downrod. (Figure 9) Carefully

reinstall hanger ball onto rod being sure that

cross pin is in correct position, set screws are

tighten and wires are not twisted.

Secure the hanger bracket to the ceiling

outlet box with the screws and washers

provided with your outlet box. (Figure 5)

from the motor

assembly.(Figure 6)

Loosen the two set screws

6. Now lift motor assembly into position and place

hanger ball into hanger bracket. Rotate until the

check groove

rotate if this is done correctly.

drops into the registration slot and

seats firmly. (Figure 10) Downrod should not

Figure 6

Downrod

Supply

wires

Figure 8 Figure 10

Registration

slot

Figure 5

Cross pin

Hanger

ball

Downrod

Figure 7

Outlet box

Hanger bracket

Hitch pin Lock pin

Set

screws

Motor Collar

Tighten

Screws

Firmly

Hitch Pin

Hanger ball

Ceiling

Canopy

Lock Pin

Coupling

cover

Canopy cover

Downrod

Lead Wires

Figure 9

Remove the hitch pin and lock pin

from downrod .Remove hanger ball from

downrod assembly by loosening set screw,

removing the cross pin,and sliding ball

off rod .

(Figure 7)

Figure 12

Receiver

Hanger

bracket

Figure 11

Code switch

Rubber

cover

Making the Electrical

Connections

1. Insert the receiver into the hanger

bracket with the flat side of the receiver

facing the ceiling. (Figure 12)

2. Motor to Receiver Electrical Connections:

Connect the black wire from the fan to black

wire marked "TO MOTOR L".

Connect the white wire from the fan to

thewhite wire marked "TO MOTOR N" from

the receiver. Connect the blue wire from the

fan to the blue wire marked "For Light" from

the receiver. Secure the wire connections

with the plastic wire nuts provided. (Figure

13)

3. Receiver to House Supply Wires Electrical

Connections: Connect the black (hot) wire

from the ceiling to the black wire marked

“AC in L" from the receiver. Connect the

white (neutral) wire from the ceiling to the

white wire marked “AC in N" from the

4 . If your outlet box has a ground wire

(green or bare copper) connect it to the fan

ground wires and the hanger bracket ground

(Figure 13)

WARNING: To avoid possible electrical

shock, be sure electricity is turned off at

the main fuse box before wiring.

Receiver. Secure the wire connections

with plastic wire nuts provided.

(Figure 13)

wire. Secured the wire connection with a

plastic nut provided. After connecting the

wires spread them apart so that the green

and white wires are on one side of the

outlet box and black and blue wires are on

the other side. Carefully tuck the wire

connections up into the outlet box.

NOTE:

This remote control unit is equipped with

16 code combinations to prevent possible

interference from or to other remote units.

The frequency switches on your receiver

and transmitter have been preset at the

factory. Please recheck to make sure the

switches on transmitter and receiver are set

to the same position, any combination of

settings will operate the fan as long as the

transmitter and receiver are set to the same

position. (Figure 11)

MAKE SURE TAB AT BOTTOM OF HANGER

BRACKET IS PROPERLY SEATED IN GROOVE OF HANGER

BALL BEFORE

ATTACHING CANOPY TO BRACKET. FAILURE

TO PROPERLY SEAT TAB IN GROOVE COULD CAUSE

DAMAGE TO ELECTRICAL WIRING.

Figure 14

Outlet box

Hanger

bracket

Canopy

Screw

Canopy

cover

Lead Wires

Ball/Downrod

Assembly

Finishing the Installation

1. Tuck connections neatly into ceiling outlet box.

2. Remove one screw from the hanger bracket and loosen the other screw around

1/4″.

3. Align the canopy up to ceiling and over the loose screw. Place the canopy into

key hole and rotate canopy clockwise. (Figure 14)

4.Secure the canopy by use previous removed and loosened screw.

5. Place the canopy cover to the canopy and rotate canopy cover clockwise until

it is locked into right position.(Figure 14)

WARNING

SUPPLY CIRCUIT

Ground

Conductor

Outlet Box

Green

Ground

Lead

Ground to

Downrod

BLACK

WHITE

BLACK

BLUE

GREEN

Figure 13

Attaching the Fan Blades

The following procedure should correct

most fan wobble. Check after each step.

1. Check that all blades and blade holder

screws are secure.

2. Most fan wobble problems are caused

when blade levels are unequal. Check this

level by selecting a point on the ceiling

above the tip of one of the blades. Measure

this distance as shown in Figure 18. Rotate

the fan until the next blade is positioned for

measurement. Repeat for each blade. The

distance should be equal within 1/8".

(Figure18)

If all blade levels are not equal, you can

adjust the blade level with the following

procedure.

3. Use the enclosed Blade Balancing Kit if

the blade wobble is still noticeable. Please

refer to the introduction provide in the

blade balancing kit, which is individual

packed.

4. If the blade wobble is still noticeable,

interchanging two adjacent (side

by side)

blades can redistribute the weight and

possibly result in smoother operation.

Touching

ceiling

Figure 18

Figure 17

Figure 16

1.Attach the fan blades to the blade holders

by using three screws ( the loose parts bag: a)

and paper washers as shown in Figure 15.

Start a screw into the blade holder, do not

tighten. Repeat for the 2 remaining screws

and washers.

2 .Tighten each screw securely starting with the

center screw. Make sure the blade is straight.

Repeat process for the other blades.

3.Remove the plastic blocks before installing

the blade holder to the fly wheel, discard the

plastic blocks but keep the screws. (Figure

16)

Tighten the blade assemblies onto fly

wheel by tightening two screws previously

removed from the fly wheel. Repeat process

for the other blade holders. (Figure 16)

5. Tighten a small fan blade to the fly wheel

with 3 blade screws (the loose parts bag: b )

provided. Repeat process for the other

blades.(Figure 17)

Blade

holder Blade

Screws

Paper

Washer

Figure 15

Table of contents

Other HAMPTON BAY Fan manuals

HAMPTON BAY

HAMPTON BAY Renwick User manual

HAMPTON BAY

HAMPTON BAY 699 810 User manual

HAMPTON BAY

HAMPTON BAY Vasner User manual

HAMPTON BAY

HAMPTON BAY Altura User manual

HAMPTON BAY

HAMPTON BAY GAZEBO YG188-BN User manual

HAMPTON BAY

HAMPTON BAY AK376-MBK User manual

HAMPTON BAY

HAMPTON BAY ASHBURTON YG593-TB User manual

HAMPTON BAY

HAMPTON BAY 7107-03 User manual

HAMPTON BAY

HAMPTON BAY AVERLY AK18B-BN User manual

HAMPTON BAY

HAMPTON BAY AC457-WB User manual

HAMPTON BAY

HAMPTON BAY 654 451 User manual

HAMPTON BAY

HAMPTON BAY San Lorenzo User manual

HAMPTON BAY

HAMPTON BAY SENZE 24816-021 User manual

HAMPTON BAY

HAMPTON BAY WITHROP 656 413 User manual

HAMPTON BAY

HAMPTON BAY GLENDALE III AK488-MBK User manual

HAMPTON BAY

HAMPTON BAY PALMARIA EF200S(X)-52 User manual

HAMPTON BAY

HAMPTON BAY 54" Tropics User manual

HAMPTON BAY

HAMPTON BAY MADISON AK30A-BN User manual

HAMPTON BAY

HAMPTON BAY Moonlight 458-241 User manual

HAMPTON BAY

HAMPTON BAY 132 cm Fan User manual

HAMPTON BAY

HAMPTON BAY SOUTHWIND II 52-RMGII User manual

HAMPTON BAY

HAMPTON BAY HAVANA 48-HVA User manual

HAMPTON BAY

HAMPTON BAY Springview User manual

HAMPTON BAY

HAMPTON BAY 51315 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual