HAMPTON BAY 786-756 User manual

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

786-756

219054

718212343425

Hampton Bay Lifetime Motor Warranty

The retailer warrants the fan motor to be free from defects in workmanship and material

present at time of shipment from the factory for a lifetime after the date of purchase by the

original purchaser. The retailer also warrants that all other fan parts, excluding any glass or

plexiglass parts, to be free fromdefects in workmanshipand material at the time of shipment

from the factory for a period of one year after the date of purchase by the original purchaser.

We agree to correct such defects withoutcharge or at our option replace with a comparable or

superior model ifthe product isreturned to the retailer. To obtain warranty service,you must

present a copy of the receipt as proof of purchase. All costs of removing and reinstalling the

product are your responsibility. Damage to any part such as by accident or misuse or

improper installation or by affixing any accessories, is not covered by this warranty.

Because of varying climatic conditions in the United States this warranty does not cover any

changes in brass finish, including rusting, pitting, corroding, tarnishing or peeling. Brass

finishes of this type give their longest useful life when protected from varying weather

conditions. A certain amount of wobble is normal and should not be considered a defect.

Servicing performed by unauthorized persons shall render the warranty invalid. There is no

other express warranty. The retailer hereby disclaims any and all warranties,

including but not limited to. Those of merchantability and fitness for a particular

purpose to the extent permitted by law. The duration of any implied warranty which

cannot be disclaimedis limited to the time periodas specified in the express warranty. Some

states do not allow limitation on how long an implied warranty lasts, so the above limitation

may not apply to you. The retailer shall not be liable for incidental, consequential, or

special damages arising out of or in connection with product use or performance except

as may otherwise be accorded by law. Some states do not allow the exclusion of incidental

or consequential damages, so the above exclusion or limitation may not apply to you. This

warranty gives specific legal rights, and you may also have other rights which vary from

state to state. This warranty supersedes all priorwarranties.

Hampton Bay Lifetime Motor Warranty

Table of Contents

Safety Rules..........................................................................................................

Unpacking Your Fan...............................................................................................

Installing Your Fan................................................................................................

Hanging The Fan....................................................................................................

Electrical Connection.............................................................................................

Finishing the Installation........................................................................................

Attaching the Fan Blades........................................................................................

Installing the Light Kit...........................................................................................

Operating the Transmitter.......................................................................................

Care of Your Fan....................................................................................................

Troubleshooting....................................................................................................

Specifications.......................................................................................................

1. Before you begin installing the fan, shut power off at the

circuit breaker ofthe fuse box.

2. Be cautious! Read all instructions and safety information

before installing your new fan. Review accompanying

assembly diagrams.

3. Make sure that all electrical connections comply with

local codes, ordinances, or National Electrical Codes.

Hire a qualified electrician or consult a do-it-yourself

wiring handbook if you are unfamiliar with installing

electrical wiring.

4. Make sure the installation site you choose allows the fan

blades to rotate without any obstructions. Allow a

minimum clearance of 7 feet from the floor and 18 inches

from the tipof the bladesto the wall.

5. If you are mounting the fan to a ceiling fan outlet box, use

a U.L. Listed metal octagonal outlet box marked

"Acceptable for Fan Support". Secure the box directly to

the building structure. The outlet box and its support must

be able to support the moving weight of the fan (at least 50

pounds) Do notuse a plasticbox

6. Caution: To reduce the risk of injury use only the screws

provided with the outlet box in conjunction with the lock

washers provided withthe fan.

7. If you are mounting the fan to a joist, make sure it is able

to support themoving weight ofthe fan (at least 50 pounds).

1. Safety Rules

8. After you install thefan, make sure that all mounting components

are secured toprevent the fanfrom falling.

9. Do not insert anything into the fan blades while the fan is

operating.

10. Turn the fan off and wait for the blades to stop completely before

changing the fandirection.

NOTE: The important safeguards and instructions appearing in this

manual are not meant to cover all possible conditions and situations

that may occur. It must be understood thatcommon sense, caution and

care are factors which can not be built into this product. These factors

must be supplied by the person (s) installing, caring for and operating

the unit.

TO REDUCETHE RISK OFFIRE, ELECTRIC SHOCKOR OTHER PERSONAL

INJURY, MOUNT FAN UNLY TOA U.L. LISTED OUTLETBOX OR SUPPORTING

SYSTEM MARKEDACCEPTABLE FORFAN SUPPORT ANDUSE MOUNTING

SCREWS PROVIDED WITHTHE OUTLET BOX OR INCONJUCTION WITH THE

LOCK WASHERS PROVIDED WITHTHE FAN. MOST OUTLETBOXES

COMMONLYUSED FOR FAN SUPPORTOF LIGHTING FIXTURESARE NOT

ACCEPTABLE FORFAN SUPPORT ANDNEED TO BE REPLACED. CONSULT A

QUALIFIED ELECTRICIAN IFIN DOUBT.

TO REDUCETHE RISK OFPERSONAL INJURY,DO NOT BENDTHE BLADE

HOLDERS WHILE INSTALLING, BALANCING THEBLADES OR CLEANING

THE FAN.DO NOT INSERT FOREIGN OBJECTSBETWEEN ROTATING FAN

BLADES.

TO REDUCETHE RISK OFFIRE OR ELECTRIC SHOCK, DO NOTUSE THIS

WITH ANYSOLID-STATE SPEED CONTROLDEVICE.

WARNING

NOTE

READ AND SAVE ALLINSTRUCTIONS!

Unpack your fanand check thecontents. You should havethe following items:

Package Contents 2.

1. Fan blades(5 )

7. Coupling cover

Hanger bracket

3. Canopy

4. Canopy cover

5. Rubber cover

6a. Standard downrodass'y

6b. Minimum-length downrod(for close

to ceiling mountingonly)

8. Fan motor/housingass'y

9. Light kithousing

10. Glass shade

11. Glassframe

12. Receiver with6 wire nuts

13. Remote control

14.

15. Balancing kit

14 Watt compact fluorescentbulb

a. Mounting Hardware:

Wire nuts(3 PCs.)

b. BladeAttachment Hardware:

Screws (16 PCs.)

Fiber washers (16PCs.)

c. Light KitHardware:

Thumb screws (1PCs.)

d. Light KitHousing AssemblyScrew:

Screws with lockwashers (5 Purchase.)

LO MED HI

FAN OFF

LIGHT/ DIMMER

710

Phillips screw driver; slotted screw driver; step-

ladder; wire cutters;electrical tape.

If there isn't an existing mounting box, then read

the following instructions. Disconnect the power

by removing fuses or turning off circuit

breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and building

materials. The outlet box and its support must be

able to fully support the moving weight of the fan

(at least 50 lbs.). Use a U. L. Listed metal outlet

box. Do notuse a plasticoutlet box.

Figure 1, 2 and 3 are examples of different ways to

mount the outletbox.

Note: You may need alonger downrod tomaintain

proper blade clearance when installing on a steep,

sloped ceiling. Longer downrods are available

from your HamptonBay dealer.

To hang your fan where there is an existing fixture

but no ceiling joist, you may need to install a

hanger bar as shown in Fig. 4 (available at our

Hampton Bay dealer).

Tools Required

Mounting Options

3. Installing Your Fan

Outlet box

Figure 1

Ceiling

joist

Ceiling

joist

Cross brace

Outlet box

Figure 2

Ceiling joist

or cross brace Parallel

wood brace

Provide strong

support

Recessed

outlet box

Hanger

opening must

be facing up-side

Figure 3

Angled ceiling

maximum

23 angle

Outlet box

Figure 4

Ceiling

joist

Hanger bar

(optional)

Hanger

bracket

Hanging the Fan 4.

REMEMBER to turn off the power.

Follow the steps below to hang your fan

properly:

Step 1. Secure the hanger bracket to the

ceiling outlet box using screws included

with your outlet box, lock washers

included with thefan. (Fig.5)

Step 2. Loosen the two set screws and

in the top

coupling of themotor assembly. (Fig. 6)

Step 3. Remove hanger ball from downrod

assembly by loosening set screw,

removing the cross pin, and sliding ball off

rod. (Fig.7)

Step 4. Carefully feed fan wires up

through the downrod. (Fig. 8) Thread the

rod into the coupling. Next line up holes

and replace lock pin and hitch pin. Tighten

set screws.

Step 5. Slip coupling cover, canopy cover

and canopy onto downrod. (Fig. 9)

Carefully reinstall

remove the hitchpin and lock pin

hanger ball onto rod

being sure that cross pin is in correct

position, set screws are tighten and wires

are not twisted.

Step 6.

Now lift motor assembly into position

and place hanger ball into hanger bracket.

Rotate until the check groove has dropped

into the registration slot and seats firmly.

(Fig. 10) Rod should not rotate if this is

done correctly.

Place rubber cover onto the hanger

ball .

Outlet box

Hanger bracket

Cross pin

Hanger

ball

Downrod

Supply

wires

Figure 5

Figure 7 Figure 8

Figure 6 Figure 9

Figure 10

Registration

slot

Hitch

pin Lock

Set

screws

Downrod

Coupling

*Omit coupling

cover when

downrod

cover

using

the minimum-length

Canopy

Canopy cover

Hanger ball

Rubber cover

Hitch pin Lock pin

Set screws

WARNING: To avoid possible electrical

shock be sure electricity is turned off at the

main fuse orbreaker box beforewiring.

NOTE: The Hand Held Remote or Wall

Control units included with your ceiling fan

are equipped with 16 code combinations to

prevent possible interference from or to other

remote units. The frequency switches on your

Receiver and Transmitter units have been

preset at the factory, please re-check to make

sure the switches on both units are set to the

same positions. The frequency settings should

be changed only in case of interference or if a

second or more remote controlled ceiling fans

are installed in the same structure. Any code

combination will operate the ceiling fan and

light as long as the Receiver and Transmitter

units are setto the samecodes (Fig. 11)

Step 1. Insert Receiver into Hanger Bracket

with the flat side of the Receiver facing the

ceiling. (Fig. 12)

Step 2. Motor to Receiver Electrical

Connections: Connect the WHITE wire from

the fan to the WHITE wire marked "TO

MOTOR N" from the Receiver. Connect the

BLACK wire fromthe fan to the BLACK Wire

marked "TO MOTOR L" from the Receiver.

Connect the BLUE wire from the fan to the

BLUE wire marked "For Light" from the

Receiver. NOTE: If your ceilingfan features

an UP Light: Connect the ORANGE wire

from the fan to the ORANGE wire marked

"For Up Light"from the Receiver. Otherwise

disregard this step and proceed to secure all

wire connections with the plastic wire nuts

provided. (Fig. 13)

connectors

Step 3. Receiver to House Supply Wires

Electrical Connections: Connect the WHITE

wire (Neutral) from the outlet box to the

WHITE wire marked "AC in N" from the

receiver. Connect the BLACK wire (Hot)

from the outlet box to the BLACK wire

marked "AC in L" from the receiver. Secure

all wire connections with the plastic wire

nuts provided. (Fig.13 )

Step 4. If your outlet box has a GROUND

wire (Green or Bare Copper) connect this

wire to the Hanger Ball and Hanger Bracket

Ground wires. If your outlet box does not

have a Ground Wire, then connect the

Hanger Ball and Hanger Bracket Ground

Wires together. Secure wire connection with

the plastic wirenut provided. (Fig.13 )

After all are made, checkto make

sure there are no loose strands. As an

additional precaution we suggest to secure

the plastic wire connectors to the wires with

electrical tape.

ONON

Figure 11

Figure 12

Receiver

Hanger bracket

5. Electrical Connections

Note: The transmitter only works within 40

feet from receiver.

Figure 14

Outlet box

Hanger

bracket

Hanger

ball

Canopy

cover

White (neutral)

Green or bare

copper (ground)

White ("AC INN")

White ("to motor N")

Ground

(green)

(Connect to

ground wire on

hanger bracket

if no house

ground wire

exists.)

Outlet box

Black (hot)

Black ("AC INL")

Black ("to motor L")

Receiver

Blue ("for light")

Blue (light)

Black (motor)

Fan

Figure 13

Step 1. Tuck connections neatly into ceiling

outlet box.

Step 2. Slide the canopy up to ceiling and

over the two crews on hanger bracket. Rotate

canopy clockwise. Next, while holding the

canopy with onehand, slide the canopy cover

over the screws and rotate clockwise until

tight. Note: adjust the canopy screws as

necessary until the canopy and canopy cover

are snug. (Fig.14)

Finishing the Installation 6.

THE FOLLOWING OPERATIONS MUST BE

ACCOMPLISHED BEFORE INSTALLING

THE LIGHT KIT.

Step 1. Insert one fan blade into the blade slot on

the motor housing and secure with three screws

and washers. Securely tighten screws. Repeat

process with otherblades.

Blade

Motor

housing

Screws

Washers

Figure 15

7. Attaching the Fan Blades

REMEMBER to disconnect the power.

The fan blades must already be attached to

the fan.

Your fan and light kit, though pre-wired,

have been disassembled at the factory to

ease in shipping. Please follow these steps

to complete theinstallation of yourfan.

Step 1. (Fig. 16) Remove 1 of the 3 screws

from the

and loosen the other 2 screws. (Do

not remove)

bottom of thebottom of themotor

housing

Bring the Light Kit Housing

close to the Motor Housing, Pass the two

wires from the motor through the access

hole of theLight Kit Housing.

Step 2. (Fig. 16)Proceed to make the wire

connections by snapping the two

connectors from the motor to the two

connectors from theLight Kit Housing.

Step 4. (Fig. 17) Place the glass shade into

the glass frameand secure withfour nuts.

Step 5. (Fig. 18)

Step 3. (Fig. 16) Place the key holes on the

light kit housing over the 2 screws

previously loosened from the mounting

ring, turn light kit housing until it locks in

place at thenarrow section ofthe key holes.

Secure by tightening the 2 screws

previously loosened and the one

previously removed.

Install 1 x 14 Watt

compact fluorescent bulbs(included).

Step 6. (Fig. 18) Take the glass shade and

glass frame assembly and place it over the

light kit housing, secure it in place by

tightening 5 screws from the light kit

housing.

Figure 16

Figure 17

Figure 18

Bulb

Installing the Light Kit 8.

Table of contents

Other HAMPTON BAY Fan manuals

HAMPTON BAY

HAMPTON BAY SEAPORT AL634-NI User manual

HAMPTON BAY

HAMPTON BAY WILLIAMSON 37302 User manual

HAMPTON BAY

HAMPTON BAY Alida User manual

HAMPTON BAY

HAMPTON BAY Farmington User manual

HAMPTON BAY

HAMPTON BAY Gazebo II Plus User manual

HAMPTON BAY

HAMPTON BAY Cassaro User manual

HAMPTON BAY

HAMPTON BAY Winfield User manual

HAMPTON BAY

HAMPTON BAY AC457-WB User manual

HAMPTON BAY

HAMPTON BAY BPT13-14HD User manual

HAMPTON BAY

HAMPTON BAY Devereaux II User manual

HAMPTON BAY

HAMPTON BAY FC120-CARL User manual

HAMPTON BAY

HAMPTON BAY Farmington User manual

HAMPTON BAY

HAMPTON BAY Mercer 52 inch User manual

HAMPTON BAY

HAMPTON BAY HARPER AM214-WH User manual

HAMPTON BAY

HAMPTON BAY SW18030 ORB User manual

HAMPTON BAY

HAMPTON BAY AK408H-BN User manual

HAMPTON BAY

HAMPTON BAY AM212-ORB User manual

HAMPTON BAY

HAMPTON BAY 7136-01 User manual

HAMPTON BAY

HAMPTON BAY AM212INL-WH User manual

HAMPTON BAY

HAMPTON BAY Algiers 672 099 User manual

HAMPTON BAY

HAMPTON BAY Rocio User manual

HAMPTON BAY

HAMPTON BAY 394-443 User manual

HAMPTON BAY

HAMPTON BAY ROANOKE YG216C-NI User manual

HAMPTON BAY

HAMPTON BAY Devereaux II User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual