HAMPTON BAY 326-722 User manual

Hampton Bay Lifetime Limited Warranty

The retailer warrants the fan motor to be free from defects in workmanship and material

present at time of shipment from the factory for a lifetime after the date of purchase by the

original purchaser. The retailer also warrants that all other fan parts, excluding any glass or

plexiglass blades, to be free from defects in workmanship and material at the time of

shipment from the factory for a period of one year after the date of purchase by the original

purchaser. We agree to correct such defects without charge or at our option replace with a

comparable or superior model if the product is returned to the retailer. To obtain warranty

service, you must present a copy of the receipt as proof of purchase. All costs of removing

and reinstalling the product are your responsibility. Damage to any part such as by accident

or misuse or improper installation or by affixing any accessories, is not covered by this

warranty. Because of varying climatic conditions in the United States this warranty does not

cover any changes in brass finish, including rusting, pitting, corroding, tarnishing or

peeling. Brass finishes of this type give their longest useful life when protected from

varying weather conditions. A certain amount of wobble is normal and should not be

considered a defect. Servicing performed by unauthorized persons shall render the warranty

invalid. There is no other express warranty. The retailer hereby disclaims any and all

warranties, including but not limited to. Those of merchantability and fitness for a

particular purpose to the extent permitted by law. The duration of any implied warranty

which cannot be disclaimed is limited to the time period as specified in the express warranty.

Some states do not allow limitation on how long an implied warranty lasts, so the above

limitation may not apply to you. The retailer shall not be liable for incidental,

consequential, or special damages arising out of or in connection with product use or

performance except as may otherwise be accorded by law. Some states do not allow the

exclusion of incidental or consequential damages, so the above exclusion or limitation may

not apply to you. This warranty gives specific legal rights, and you may also have other

rights which vary from state to state. This warranty supersedes all prior warranties.

Lifetime Limited Warranty

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

326-722

326-946

11289

792145350651(326-946)

792145350644(326-722)

1. To reduce the risk of electric shock, insure electricity has been turned

off at the circuit breaker or fuse box before beginning.

2. All wiring must be in accordance with the National Electrical Code and

local electrical codes. Electrical installation should be performed by a

qualified licensed electrician.

3. WARNING: To reduce the risk of electrical shock and fire, do not use

this fan with any solid-state fan speed control device.

4. WARNING: To reduce the risk of personal injury, use only the two steel

screws (and lock washers) provided with the outlet box for mounting to

the outlet box. Most outlet boxes commonly used for the support of

lighting fixtures are not acceptable for fan support and may need to be

replaced, consult a qualified electrician if in doubt.

7. Do not operate reversing switch while fan blades are in motion. Fan

must be turned off and blades stopped before reversing blade

direction.

8. Avoid placing objects in the path of the blades.

9. To avoid personal injury or damage to the fan and other items, be

cautious when working around or cleaning the fan.

10. Do not use water or detergents when cleaning the fan or fan blades. A

dry dust cloth or lightly dampened cloth will be suitable for most

cleaning.

11. After marking electrical connections, spliced conductors should be

turned upward and pushed carefully up into outlet box. The wires

should be spread apart with the grounded conductor and the

equipment-grounding conductor on one side of the outlet box.

12. Electrical diagrams are reference only. Light kit that are not packed

with the fan must be UL Listed and marked suitable for use with the

model fan you are installing. Switches must be UL General Use

Switches. Refer to the Instructions packaged with the light kits and

switches for proper assembly.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR

FAN SUPPORT.

5. The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 50 pounds. Use only UL

Listed outlet boxes marked FOR FAN SUPPORT.

6. The fan must be mounted with a minimum of 7 feet clearance from the

trailing edge of the blades to the floor.

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE BRACKETS (ALSO REFERRED TO AS FLANGES) DURING

ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN

THE PATH OF THE BLADES.

NOTE

READ AND SAVE ALL INSTRUCTIONS!

1. Safety Rules

Unpacking Your Fan 2.

Unpack your fan and check the contents. You should have the following items:

2. Canopy assembly

3. Ball/downrod assembly

4. Collar cover

5. Fan motor assembly

6. Set of blade holders (5)

Set of blades (5) 7.

8. Glass shade (3)

9. Pull chain and fob (2)

10. 60 Watt medium base bulbs (3)

11. Balance kit

Light fixture 12. Loose parts bag containing:

a. Blade attachment hardware

(16 screws)

b. Mounting hardware

( 3 plastic wire connectors)

c. Rubber gasket

d. Light kit hardware

( 1 screw)

WARNING

DO NOT INSTALL OR USE FAN

IF ANY PART IS DAMAGED OR MISSING.

CALL TOLL FREE 877-898-1881

NOTE

FOR NON-LIGHT USE PURPOSE, THE

SWITCH HOUSING IS AVAILABLE BY

CALLING THE TOLL FREE NUMBER

877-898-1881

3. Installing Your Fan

Tools Required

P h i l l i p s s c r e w d r i v e r , s t r a i g h t s l o t

scre w d r ive r, a d j u stab l e w r e nch , st e p

ladder, and wire cutters.

Mounting Options

If there isn't an existing UL listed mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the

build i n g s t r u c t ure. U se appropr i a t e

fasteners and building materials. The outlet

box and its support must be able to fully

support the moving weight of the fan (at

least 50 lbs). Do not use plastic outlet

boxes.

Figures 1,2 and 3 are examples of different

ways to mount the outlet box.

Note: You may need a longer downrod to

maintai n proper blade clearance when

installing on a steep, sloped ceiling.

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4

(available at your Hampton Bay Retailer).

Outlet box

Provide strong

support

Recessed

outlet box

Mounting bracket

opening must be

toward the top

Outlet box

Figure 1 Figure 3

Figure 2

Figure 4

Angled ceiling

maximum

20 angle

Hanging the Fan

REMEMBER to turn off th the power. Follow

the steps below to hang your fan properly.

NOTE: This ceiling fan is supplied with two

types of hanging assemblies; the standard ceiling

installation using the downrod with ball and

socket mounting and the "close-to-ceiling"

installation. The "close-to-ceiling" installation

is recommended in rooms with less than 8-foot

ceilings or in areas where additional space is

desired from the floor to the fan blades. When

using the standard 4 1/2" downrod, the distance

from the ceiling to the bottom of the fan blades

will be approximately 12 1/2 inches. The "close-

to-ceiling" installation reduce this distance to 8-

inches. Once you have selected which mounting

system you will use, proceed with the following

instructions. Where necessary, each section of

the instructions will note the different

procedures to follow for the two types of

mounting.

STANDARD CEILING INSTALLATION

1. Remove the canopy ring from the canopy by

turning the ring to the right until it unlocks.

(Fig. 5)

2. Remove the hanger bracket from the canopy

by loosening the four screws on the top of the

canopy. Remove the two non-slotted screws

and loosen the slotted screws. This will

enable you to remove the hanger bracket.

(Figure 5)

3. Pass the 120-volt supply wires through the center

hole in the ceiling hanger bracket as shown in

Fig.6

4. Loose the two screws on the outlet box in half

way.

5. Attach the hanger bracket on the outlet box by

sliding the hanger bracket over the screws

provided with the outlet box.

6.Tighten the two screws on the outlet box securely.

7. Remove the hanger pin, lock pin and set screws

from the top of the motor assembly.

8. Route wires exiting from the top of the fan motor

through the collar cover and canopy ring. Make

sure the slot openings of the canopy ring are on

top. Route the wires through the canopy and then

through the ball/downrod assembly (Figure 6A).

9. Align the holes at the bottom of the downrod with

the holes in the collar on top of the motor housing

(Figure 6A). Carefully insert the hanger pin

through the holes in the collar and downrod. Be

careful not to jam the pin against the wiring inside

the downrod. Insert the locking pin through the

hole ins locked position, as note din the circle

inset of Figure 6A

WARNING

FAILURE TO PROPERLY INSTALL LOCKING

PIN AS NOTED IN STEP 9 COULD RESULT IN

FAN LOOSENING AND POSSIBLY FALLING.

10. Tighten two set screws on top of the fan motor

firmly. (Figure 6A)

11. Place the downrod ball into the hanger bracket

Figure 5

Ceiling

mounting

plate

Ceiling

canopy

Screws

Canopy

ring

Mounting

screws

(supplied with

electrical box)

Hook

Ceiling

mounting

plate

UL Listed

electrial

box

Slide mounting

bracket over

screw heads

Figure 6 120V Wires

4. Pass the 120-volt supply wires through the center

hole in the ceiling hanger bracket as shown in Fig.

5. Loose the two screws on the outlet box halfway.

6. Attach the hanger bracket on the outlet box by

sliding the hanger bracket over the screws provided

with the outlet box.

7. Tighten the two screws on the outlet box securely.

8. Remove three of the six screws and lock washers

(every other one) from the collar of top motor

(Figure. 7)

9. Place the rubber gasket over the remaining three

screws, route the wires exiting the top of the fan

motor through the canopy ring (make sure the slot

openings of the ring are on top). then proceed to

place the ceiling canopy over the collar at the top

of the motor. Align the mounting holes with the

holes in the motor and fasten using the screws and

lock washers provided (Fig. 7).

10.Tighten the mounting screws securely. (Fig. 7)

11.Hang the fan on the tab of the hanger bracket. Be

certain that the canopy is fully locked into tab as

shown in Fig. 8. This will allow you to make the

electrical connections.

Pin in

locked

position

Canopy ring

Hanger pin

Motor collar

Motor wires

Ball/downrod

assembly

Ceiling

canopy

Locking pin

Tighten

screws

firmly

Figure 6A

Collar cover

Figure 8

Tab

Figure 7A

Canopy

Bottom

Cover

Screw and

Lockwasher

(3 of 6 places)

Ceiling

Canopy

Figure 7

Canopy

Ring

Collar

Rubber

gasket

CLOSE-TO-CEILING INSTALLATION

1. Remove the canopy ring from the

canopy by turning the ring to the right

until it unlocks. (Fig. 5)

2. Remove the hanger bracket from the

canopy by loosening the four screws

on the top of the canopy. Remove the

two non-slotted screws and loosen the

slotted screws. This will enable you to

remove the hanger bracket. (Figure 5)

3. Remove the decorative canopy bottom

cover from the canopy by depressing

the three studs (Fig. 7A)

WARNING

FAILURE TO COMPLETELY TIGHTEN

THE THREE SCREWS IN STEP 9 COULD RESULT IN

FAN LOOSENING AND POSSIBLY FALLING.

Making the Electrical

Connections

Remember to disconnect the power.

Follow the steps below to connect the fan to your household wiring.

Use the wire connecting nuts supplied with your fan. Secure the

connectors with electrical tape. Make sure there are no loose

strands or connections.

Step 1 Connect the fan supply (black) wire and light supply (blue)

wire to the black household supply wire as shown in Figure 9.

Step 2. Connect the neutral fan (white) wire to the white neutral

household wire.

Step 3 Connect the fan ground wire (green) to the household ground

wire.

Step 4 After connecting the wires, spread them apart so that the

green and white wires are on one side of the outlet box and the black

and the blue wires are on the other side.

Step 5 Turn the connecting nuts upward and push the wiring into the

outlet box.

Figure 10 and 11 illustrate the wiring connections for optional

wall control (available at your Hampton Bay Retailer, the wire

color out of wall control may vary, see wall control's

installation manual for correct wire connections.)

NOTE

LIGHT KITS ARE AVAILABLE AT YOU

HAMPTON BAY RETAILER. THE FAN IS

ALREADY WIRED TO SUPPORT THE LIGHT KIT OPTION.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR OTHER PERSONAL INJURY.

MOUNT FAN ONLY ON AN OUTLET BOX OR SUPPORTING

SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT.

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK. DO NOT USE THIS FAN WITH ANY

SOLID-STATE SPEED CONTROL DEVICE. 6.

SUPPLY CIRCUIT

Ground

Conductor

Outlet Box

Green

Ground

Lead

Ground to

Downrod

BLACK

WHITEWHITE

BLACK

BLUE

GREEN

WHITE

BLUE

BLACK WHITE

Figure 9

Diagram indicates optional light kit wiring.

SUPPLY CIRCUIT

Ground

Conductor

Outlet Box

Green

Ground

Lead

Ground to

Downrod

BLACK

WHITE

BLACK

BLUE

GREEN

Figure 10

Diagram indicates optional light kit wiring.

Light Switch

WHITE

BLUE

BLACK WHITE

Finishing the

Installation

STANDARD CEILING INSTALLATION

Slide canopy up to the ceiling as shown in

Figure 12 l e a ving a 1/8" clearance

between the canopy and the ceiling. Make

sure you place the wires safely into outlet

box. Secure the canopy to the hanger

bracket with the four screws with your fan.

Slide the canopy ring over the canopy and

tighten by turning the ring.

WARNING

MAKE SURE TAB AT BOTTOM OF HANGER

BRACKET IS HANGER PROPERLY SEATED IN

GROOVE OF HANGER BALL BEFORE

ATTACHING CANOPY TO BRACKET. FAILURE

TO PROPERLY SEAT TAB IN GROOVE COULD

CAUSE DAMAGE TO ELECTRICAL WIRING

CLOSE-TO-CEILING INSTALLATION

Remove the fan from the tab on the hanger

bracket. Secure the canopy to the hanger

bracket as shown in Figure 13 with four

screws included with your fan. Slide the

canopy ring over the canopy and tighten

by turning the ring.

Figure 13

Figure 12

Allow 1/8"

Clearance

Allow 1/8"

Clearance

SUPPLY CIRCUIT

Ground

Conductor

Outlet Box

Green

Ground

Lead

Ground to

Downrod

BLACK

WHITE

BLACK

BLUE

GREEN

Figure 11

Diagram indicates optional light kit wiring.

Light

Fan

WHITE

BLUE

BLACK WHITE

Remove the blade attachment screws from

the fan motor assembly. Attach and adjust

fan blades according to the instructions in

the following section.

Attaching the Fan

Blades

Step 1 Attach the blades to the blade brackets

using the screws and rubber washers provided

as shown in Figure 14. Start a screw into the

bracket, but do not tighten. Repeat for the other

2 screws and washers.

Step 2 Tighten each screw securely starting

with the center screw. Make sure the blade is

straight.

Step 3 Fasten the blade assemblies to the motor

by insert the tab from the blade brackets to the

slot in the bottom motor housing, then tighten

the two screws and washers already installed in

the blade brackets (Figure 15).

Step 4 Install an optional light kit if you wish.

Follow the instructions included with the kit.

Rubber

washers

Blade

bracket

Figure 14

Motor

Blade Bracket

Slot

Tab

Figure 15

Screws

Blade

3. Use the enclosed Blade Balancing Kit if

the blade wobble is still noticeable.

4. If the blade wobble is still noticeable,

interchanging two adjacent (side by side)

blades can redistribute the weight and

possibly result in smoother operation.

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY,

DO NOT BEND THE BLADE HOLDERS

WHILE INSTALLING, BALANCING THE

BLADES, OR CLEANING THE FAN. DO NOT

INSERT FOREIGN OBJECTS BETWEEN

ROTATING FAN BLADES.

Touching

ceiling

Figure 16

All blades are grouped by weight. Because

natural woods very in density, the fan may

wobble even though the blades are weight

matched.

The following procedure should correct most

fan wobble. Check after each step.

1. Check that all blade and blade bracket screws

are secure.

2. Most fan wobble problems are caused when

blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of

one of the blades. Measure this distance as

shown in Figure 16. Rotate the fan until the next

blade is positioned for measurement. Repeat for

each blade. The distance should be equal within

1/8".

This manual suits for next models

Table of contents

Other HAMPTON BAY Fan manuals

HAMPTON BAY

HAMPTON BAY ASHBURTON YG593-BN User manual

HAMPTON BAY

HAMPTON BAY Windward II User manual

HAMPTON BAY

HAMPTON BAY STONERIDGE 51823 User manual

HAMPTON BAY

HAMPTON BAY Copperhead User manual

HAMPTON BAY

HAMPTON BAY 786-756 User manual

HAMPTON BAY

HAMPTON BAY BENNINGTON 52389 User manual

HAMPTON BAY

HAMPTON BAY Mediterranean 52" User manual

HAMPTON BAY

HAMPTON BAY BPT13-13D-1 User manual

HAMPTON BAY

HAMPTON BAY AG510-BN User manual

HAMPTON BAY

HAMPTON BAY HALWIN AK396H-BN User manual

HAMPTON BAY

HAMPTON BAY Razor User manual

HAMPTON BAY

HAMPTON BAY Farmington User manual

HAMPTON BAY

HAMPTON BAY 91646 User manual

HAMPTON BAY

HAMPTON BAY HVW-18M BK User manual

HAMPTON BAY

HAMPTON BAY METARIE II 24 User manual

HAMPTON BAY

HAMPTON BAY Colby User manual

HAMPTON BAY

HAMPTON BAY 7134-01 User manual

HAMPTON BAY

HAMPTON BAY N375A-BN User manual

HAMPTON BAY

HAMPTON BAY MINNA HE-12026 User manual

HAMPTON BAY

HAMPTON BAY PALMARIA EF200S(X)-52 User manual

HAMPTON BAY

HAMPTON BAY Home Depot SKU 110348 User manual

HAMPTON BAY

HAMPTON BAY 68144 User manual

HAMPTON BAY

HAMPTON BAY MORESCO 14411 User manual

HAMPTON BAY

HAMPTON BAY Havenville User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual