Grizzly T32796 User manual

COPYRIGHT © JULY, 2021 BY GRIZZLY INDUSTRIAL, INC.

NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

(FOR MODELS MFD. SINCE 07/21) #CS21971 PRINTED IN CHINA

Introduction

The Model T32796/T32797 Knife Sharpening

Jigs are fixtures designed to work with the Model

T32720 10" Wet Grinder. The Model T32796 is

for blades longer than 4" while the Model T32797

supports blades that are shorter than 4".

Figure 1. Example of Model T32796 in use.

V1.07.21

To reduce your risk of

serious injury, read this

entire manual BEFORE

using machine.

For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com

MODEL T32796/T32797

KNIFE SHARPENING JIGS

FOR T32720 WET GRINDER

INSTRUCTIONS

Description Qty

A. Jig (T32797 Shown) ................................... 1

B. Knob Bolt M6-1 x 20 ................................... 1

Inventory

NOTICE

If you cannot find an item on this list, care-

fully check around/inside the machine and

packaging materials. Often, these items get

lost in packaging materials while unpack-

ing or they are pre-installed at the factory.

Figure 2. Inventory.

A

B

-2- Model T32796/T32797 (Mfd. Since 07/21)

Lock Knob Clamp Knob

Figure 4. Clamp components.

Figure 5. Example of knife blade secured in

clamp (T32796 shown).

Clamp

Knob

Lock

Knob

3. DISCONNECT GRINDER FROM POWER!

4. Install tool rest in horizontal position over

grinding or stropping wheel as required by

your operation.

5. Loosen clamp knob enough to allow knife

blade to slide in (see Figure 4).

6. Loosen lock knob enough so it does not

extend through clamp plate (see Figure 4).

To use jig:

1. Rotate adjusting ring on jig shaft so flat por-

tions shown in Figure 3 are aligned.

2. Tighten adjusting ring knob until adjusting

ring is secure on jig shaft (see Figure 3).

Adjusting Ring

Jig

Shaft

Knob

Figure 3. Adjusting ring secured correctly on jig

shaft (T32797 shown).

Using Jig

Rest the tool jig against the tool rest on the Model

T32720 10" Wet Grinder to grind or strop knives

with the direction of wheel rotation. The Model

T32796 is for blades longer than 4" while the

Model T32797 supports blades that are shorter

than 4".

Eye and face injuries and respiratory prob-

lems can occur while operating this tool.

Wear personal protective equipment to

reduce your risk from these hazards.

Keep hair, clothing, and

jewelry away from mov-

ing parts at all times.

Entanglement can result

in death, amputation, or

severe crushing injuries!

7. Insert knife blade into clamp, as shown in

Figure 5, and tighten clamp knob to secure.

8. Tighten lock knob to secure (see Figure 5).

Clamp

Plate

Model T32796/T32797 (Mfd. Since 07/21) -3-

9. Rest clamp against tool rest (see Figure 6).

Figure 6. Example of grinding knife supported by

jig (T32796 shown).

Adjusting Ring

Tool Rest

10. Adjust tool rest closer to or further from

grinding or stropping wheel until approximate

desired grinding/stropping angle is achieved.

11. Adjust position of adjusting ring to fine-tune

grinding/stropping angle (see Figure 6).

12. Tilt jig and knife away from grinding wheel,

connect grinder to power, and turn machine

ON.

13. Use firm grip to return knife blade to surface

of grinding or stropping wheel to grind or strop

knife with the direction of wheel rotation. Use

smooth stroking motion and even pressure

with side of blade flat against wheel. Pivot jig

against tool rest as needed to follow contour

of blade.

This manual suits for next models

1

Other Grizzly Tools manuals

Popular Tools manuals by other brands

Martor

Martor SECUNORM 175 quick start guide

ERKCO

ERKCO 1000 user manual

jbc

jbc N4473 instruction manual

FEINMETALL

FEINMETALL FZWZ-SET-001 quick start guide

Worx Professional

Worx Professional Sonicrafter WU676 Original instructions

Gage Bilt

Gage Bilt GB713SH Original instructions

Hilti

Hilti DX 9-ENP Original operating instructions

norbar

norbar NORTRONIC 34399 Operator's manual

BGS technic

BGS technic 8578 manual

Makita

Makita DHR241 instruction manual

Motor Guard

Motor Guard JMB-1250 instructions

Power Adhesives

Power Adhesives 805-12 operating instructions

Clemco

Clemco 24189 quick start guide

VVG

VVG VNG 903 Series instruction manual

Hilti

Hilti FX 3-A operating instructions

axing

axing BWZ 5-02 Operation instructions

Dh-Robotics

Dh-Robotics RGI-100 Short manual

Goobay

Goobay 97790 user manual