Grandstream Networks GXP-285 User manual

Grandstream IP Phone Configuration Guides

www.yeastar.com Page 1

Grandstream

IP Phone

Configuration Guides

Yeastar Technology Co., Ltd.

Grandstream IP Phone Configuration Guides

www.yeastar.com Page 2

Index:

1 For Grandstream GXP-2000 ....................................................................... 3

1.1 Register with MyPBX......................................................................... 3

2 For GrandStream Handytone 386 ............................................................... 5

2.1 How to setup ATA for FAX ................................................................. 5

3 For GrandStream HandyTone 486(487), 286(287), ATA ................................ 7

3.1 How to setup ATA for MyPBX: ............................................................ 8

Grandstream IP Phone Configuration Guides

www.yeastar.com Page 3

For Grandstream GXP-2000

Important

This guide has been tested for Grandstream phones with firmware version 1.2.4.3.

Be aware that different firmware revisions may have different web interface formats

and functionality.

This guide is applicable to the following Grandstream phone models GXP 280, 285,

1200, 2000, 2010, 2020. You can follow this guide to manually configure your

phone.

Configuring the Phone to Register with MyPBX

1. Start up the phone and identify its IP Address from the LCD display. For this

example we will assume the IP Address of the phone is 192.168.5.126, and the

IP Address of MyPBX is 192.168.5.150

2. Point your browser to the web interface of the phone: http://192.168.5.126.

The default password is ‘admin’.

3. We now need to set the phone to register with MyPBX. Go to the ‘Account 1’

page:

Figure 1-1

1) Set the ‘Account Active’field to ‘yes’

2) Set the ‘Account Name’field to a name (for informational purposes only)

3) Set the ‘SIP Server’field to the IP Address of MyPBX

4) Set the ‘SIP User ID’field to the extension number you want to associate

with this phone

5) Set the ‘Authenticate ID’field to the extension's number

6) Set the ‘Authenticate Password’field to the extension's Password

7) Set the ‘Name’field to the name you would like to be displayed on other

phones when calling out

8) Set the ‘User ID is phone number’field to ‘yes’

Grandstream IP Phone Configuration Guides

www.yeastar.com Page 4

9) Set the ‘Auth Answer’field to ‘no’and the ‘Allow Auth Answer by Call-Info’

field to ‘yes’(to allow paging functionality)

Figure 1-2

10) Click the ‘Update’button at the bottom of the page, and then click the

‘Reboot’button. Your phone will restart. After rebooting, the phone will

retrieve its configuration files and register with MyPBX. This can be verified

via the ‘Extension Status’page of MyPBX Management Console.

Grandstream IP Phone Configuration Guides

www.yeastar.com Page 5

For GrandStream Handytone 386

How to setup ATA for FAX

Follow these steps to set up a GrandStream HandyTone 386 VoIP ATA with MyPBX:

1. Connect the device’s LAN port to your computer with a straight network cable.

2. The device is preconfigured with IP Address 192.168.5.126. Configure your

computer to have static IP Address 192.168.5.126, with subnet mask

255.255.255.0.

3. Launch a browser and go to http://192.168.5.126. The default username is

‘Admin’.

4. Select the ‘Basic settings’tab.

Figure 2-1

5. If your network has a DHCP Server, then select the radio button labeled

‘dynamically assigned via DHCP’.

6. If your network does NOT have a DHCP Server, then set up static IP Addressing.

From this point onwards, we will assume that the IP Address of MyPBX Server

on the network is 192.168.5.150, the IP Address of the device will be

192.168.5.150, the IP Address of the default gateway is 192.168.5.1, and the

IP Address of the DNS Server for the subnet is 10.25.0.168.

7. Scroll to the bottom of the page and click the ‘Update’button. You will be

prompted to reboot the device. Click the ‘Reboot’button. After the device has

finished rebooting, you may consult the DHCP Server’s administrative tools to

Grandstream IP Phone Configuration Guides

www.yeastar.com Page 6

retrieve the device’s new IP Address.

8. Now that you have access to the web configuration you can start configuring it

against MyPBX. Launch a browser and point it to device’s new IP Address.

9. Ensure that you have already created the extension in MyPBX. Take note of the

Authentication ID field and the Authentication password that you have entered

for the extension connected to the ATA device.

10. Go to ‘FXS PORT 1’tab.

Figure 2-2

11. Set the ‘SIP Server’field to the IP Address of the server on which MyPBX is

installed –in this example 192.168.5.150.

12. Set the ‘Outbound Proxy’field to the same value as in step 11.

13. The ‘SIP User ID’field should match the ‘Extension Number’field of the

extension in MyPBX Management Console.

14. The ‘Authenticate ID’and ‘Authenticate Password’fields must match the

Authentication ID and Password set for that extension in MyPBX Management

Console.

15. The ‘Name’field is optional. A suitable value would be the name of the user

using this phone.

16. Set ‘User ID is phone number’to ‘Yes’

17. Set ‘Sip Registration’to ‘Yes’

18. Set ‘Unregister on Reboot’to ‘Yes’

19. Set the ‘Register Expiration’field to a suitable value. For testing purposes you

may want to use 60 seconds, but once the configuration is tested a larger value

would be more appropriate to limit unnecessary network traffic. A good setting

for general use could be 3600 seconds (1 hour).

Grandstream IP Phone Configuration Guides

www.yeastar.com Page 7

20. Set ‘Enable Call Features’to ‘Yes’. This setting enables feature like transfer, on

hold etc from the analog phone connected to the FXS port of the device.

21. Set the ‘Preferred Vocoder’to choice 1: PCMU, choice 2: PCMA. The settings for

choices 3 to 6 will not come in use since they will not be used by MyPBX.

22. Set ‘Allow outgoing call without Registration’to ‘yes’.

23. Scroll to the bottom of the page and click the ‘Update’button. You will be

prompted to reboot the device. Click the ‘Reboot’button.

24. Repeat steps 11-24 for the configuring ‘FXS port 2’.

25. After the HandyTone has restarted, switch to MyPBX Management Console, and

click on ‘Line Status’, your new extension connected to the PBX should be listed

with a blue status light.

For GrandStream HandyTone

486(487), 286(287), ATA

Configuring GrandStream HandyTone 486(487), 286(287), ATA for

MyPBX

Important

This guide has been tested with firmware version 1.1.0.37. Be aware that different

firmware revisions may have different web interface formats and functionality. This

is based on a new ATA OR one that has been reset to factory defaults.

Grandstream IP Phone Configuration Guides

www.yeastar.com Page 8

How to setup ATA for MyPBX:

Connect the LAN to the WAN port of the HandyTone

1. Connect an analog phone to the HandyTone phone port. Pick up the headset

and press ‘****’. This will start up a Voice Prompt Menu. Now press ‘02’to listen

to the IP address that was assigned to the device by the DHCP server

2. Enable the wan side Web access, dial ‘****’and then ‘129’

3. Launch a browser and go to the IP Address, The default username is ‘admin’,

Select the ‘Advanced Settings 1’tab.

Figure 3-1

4. Set the ‘SIP Server’field to the IP Address of the server on which MyPBX is

installed –in this example 192.168.5.150

5. Set the ‘Outbound Proxy’field to the same value as sip server

6. The ‘SIP User ID’field should match the ‘Extension Number’field of the

extension created for this phone in MyPBX Management Console

7. In the ‘Authenticate ID’and ‘Authenticate Password’fields must match the

‘extension’and ‘Password’set for that extension in MyPBX Management

Console

8. The ‘Name’field is optional. A suitable value would be the name of the user

using this phone

9. Set the ‘Preferred Vocoder’to choice 1: PCMU, choice 2: PCMA. The settings for

choices 3 to 7 will not come in use since they will not be used by MyPBX

10. Set ‘payload type’to 101 for successful registration

11. Set ‘User ID is phone number’ to ‘Yes’

Grandstream IP Phone Configuration Guides

www.yeastar.com Page 9

12. Set ‘Sip Registration’to ‘Yes’

13. Set ‘Unregister on Reboot’to ‘Yes’

14. Set the ‘Register Expiration’field to a suitable value. For testing purposes you

may want to use 60 seconds, but once configuration is tested a larger value

would be more appropriate to limit unnecessary network traffic. A good setting

for general use could be 3600 seconds (1 hour)

15. Set ‘Allow outgoing call without Registration’to yes

16. Set ‘Enable Call Features’to ‘Yes’. This setting enables features like transfer, on

hold etc from the analog phone connected to the FXS port of the device

17. Scroll to the bottom of the page and click the ‘Update’button. You will be

prompted to reboot the device. Click the ‘Reboot’button

Figure 3-2

18. After the HandyTone has restarted, switch to MyPBX Management Console, and

click on ’Line Status’. In the section ‘Extensions’, your new extension connected

to the PBX should be listed with a blue status light

This manual suits for next models

Table of contents

Other Grandstream Networks IP Phone manuals

Grandstream Networks

Grandstream Networks GXP1760W User manual

Grandstream Networks

Grandstream Networks GRP261 Series User manual

Grandstream Networks

Grandstream Networks GXP21 Series User manual

Grandstream Networks

Grandstream Networks Grandstream GXP-2010 User manual

Grandstream Networks

Grandstream Networks GXP2170 User manual

Grandstream Networks

Grandstream Networks GXV3240 User manual

Grandstream Networks

Grandstream Networks Grandstream GXP-2000 Operator's manual

Grandstream Networks

Grandstream Networks HT813 User manual

Grandstream Networks

Grandstream Networks 100 Sereis User manual

Grandstream Networks

Grandstream Networks GXP1615 User manual

Grandstream Networks

Grandstream Networks DP750 Instruction Manual

Grandstream Networks

Grandstream Networks DP715 Instruction sheet

Grandstream Networks

Grandstream Networks GXP1628 User manual

Grandstream Networks

Grandstream Networks GRP2615 Instruction Manual

Grandstream Networks

Grandstream Networks GXP1630 User manual

Grandstream Networks

Grandstream Networks GXV3240 User manual

Grandstream Networks

Grandstream Networks GRP2616 User manual

Grandstream Networks

Grandstream Networks GXV-3000 User manual

Grandstream Networks

Grandstream Networks LXP100 User manual

Grandstream Networks

Grandstream Networks GXV3370 User manual

Grandstream Networks

Grandstream Networks BT-200 User manual

Grandstream Networks

Grandstream Networks GRP2603 User manual

Grandstream Networks

Grandstream Networks GXP2130 Series User manual

Grandstream Networks

Grandstream Networks GXP1610 Instruction manual

Popular IP Phone manuals by other brands

Alcatel

Alcatel 4028 manual

Polycom

Polycom Polycom VVX 600 quick reference

Polycom

Polycom SoundPoint IP 450 datasheet

Cisco

Cisco SPA-500 Series user guide

Polycom

Polycom SoundPoint IP 650 user guide

Proximus

Proximus Maestro 3016 IP quick start guide

Fanvil

Fanvil X4 user manual

Cisco

Cisco 7962 user guide

Snom

Snom 320 quick start guide

Yealink

Yealink Yealink SIP-T46G Guide

Avaya

Avaya 4625SW user guide

Yealink

Yealink SIP-T52S quick start guide

Nortel

Nortel 1140E Getting started

Nexotek

Nexotek NT-P500 user manual

Avaya

Avaya Integral 5 R3.0 user guide

GE 28320EE2 - Dect 6.0 InfoLink 2 user guide

Avaya

Avaya 4600 Series Administrator's guide

Mitel

Mitel MIVOICE OFFICE 400 6940 SIP user guide