GE 45413 User manual
Personal Security
Glass
Vibration
Alarm
User Manual
Do not use in wet locations
Important Safeguards 4
Introduction 5
Installing Batteries 6
Low Battery Indicator 7
Installation 7-9
Operation 10
Sensitivity Selection 10
Care and Maintenance 11
Specification 12
Warning 13-15
Table of Contents
Before connecting or operating the Glass Vibration Alarm, please read these instructions
carefully and save this manual for future reference.
This user manual explains in simple steps how to install, use and care for your new Personal
Security Glass Vibration Alarm.
If you have any questions or would like additional information please visit our web site
www.jascoproducts.com or contact our Technical Support Group at 1-800-654-8483,
option 4.
4
Important safeguards
Pre cautions
1. Do not attempt to disassemble the Glass Vibration Alarm, unless described in the user’s
manual. There are no user serviceable parts.
2. Handle with Care – Avoid striking or shaking. Improper use or storage could damage
the Glass Vibration Alarm. Modifying the device or its internal components can cause a
malfunction and void the Alarm’s warranty.
3. If you feel the Glass Vibration Alarm is not operating correctly or as described, please
contact Technical Support for assistance (1-800-654-8483), option 4.
5
Introduction
The Glass Vibration Alarm is designed to be mounted on glass where there is a potential
for tampering or breakage. The thin profile makes it ideal for mounting between sliding
windows and glass doors. When mounted properly it will sound an alarm when glass
has been broken or there is excessive
vibration. The alarm has a printed
warning label visible from the outside. (HI/LOW)
High & Low
sensitivity section
Indicator Light
Alarm
Siren
Battery Test Button
Power ON/OFF
Battery
compartment
6
Installing Batteries
The alarm requires (4) LR44 or 357 button batteries (included).
Average battery life for typical usage is up to one year.
1. Make sure alarm ON/OFF switch is set to “OFF” position.
2. Remove the screw securing the battery compartment cover.
3. Slide cover off the battery compartment in direction of arrow.
4. Insert (4) LR44 button batteries noting polarity.
5. Replace battery compartment cover.
6. Secure the battery cover screw.
7
Low Battery Indicator
The alarm has a low battery indicator light. Push the ‘Battery Test’ button located
on the front of the unit. Batteries can be tested in either ON/OFF mode. If the red
light illuminates when the button is pressed, the batteries are good. If the light fails
to illuminate, replace all batteries.
Installation
Your GE Personal Security Glass Vibration Alarm is an octagon shaped alarm with
a visible warning sticker on opposite side (facing out). Before mounting to glass
ensure proper orientation so that warning sticker can be easily viewed.
8
1. Locate a position on the window or sliding glass door to be protected that allows
easy access to the alarm controls, and access to the battery door. Make sure
switch is in the OFF position, and the mounting surface is clean and dry. For best
results, clean the mounting surface with a mixture of 50% isopropyl alcohol and
50% water. Allow to dry.
2. Remove protective covering from the back side of the double-sided tape and lightly
position the alarm on the glass window or sliding glass door in a visible location.
3. Ensure that warning label can be easily viewed from outside and that you can easily
access all the controls and battery door. Once correct placement is established,
apply pressure to secure double-sided tape.
9
Your GE Personal Security Glass Vibration Alarm has a thin profile and can be
placed between sliding windows and sliding glass doors. Note: There must be at
least a 3/8” gap between windows and doors to prevent damage to alarm.
Window and door preferred
mounting location
10
Operation
1. To arm the alarm, locate the ON/OFF switch on the side. Slide the switch to the
“ON” position. When in the “ON” position, if the protected window or door is struck
or hit, the alarm siren will sound continuously until disarmed.
2. To disarm the alarm, slide the switch to the OFF position.
Sensitivity Selection
The GE Glass Vibration Alarm has a selectable HI/LO sensitivity switch. Locate the
switch on the side and select the desired sensitivity setting. Select “LO” position for
windows or doors that may be exposed to vibration from strong winds.
Table of contents
Other GE Security System manuals
GE
GE SIMON XT User manual
GE
GE Security Pro 500 User manual
GE
GE 60-960-95 User manual
GE
GE Interlogix 60-875 Simon User manual
GE
GE 8RP Board Assembly instructions
GE
GE Interlogix 60-875 Simon User manual
GE
GE Simon XT V2 User manual
GE
GE JSC1300 User manual
GE
GE DeluxeDoorAlarm User manual
GE
GE 45255 User manual
GE
GE Telligence Patient-Staff Communications... User manual
GE
GE ARITECH AS399 User manual
GE
GE 600-1064-95R b User manual
GE
GE Security Pro 1000 User manual
GE
GE SIMON XT Instruction manual
GE
GE 45411 User manual
GE
GE 868 GEN2 User manual
GE
GE Advent User manual
GE
GE Concord express User manual
GE
GE Concord Ultra User manual
Popular Security System manuals by other brands
EDM
EDM Solution 6+6 Wireless-AE installation manual
Highway Safety Group
Highway Safety Group EA401 user manual
Siren
Siren LED GSM operating manual
Detection Systems
Detection Systems 7090i Installation and programming manual
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 instructions
Siemens
Siemens FDM273 manual