Fujitsu D2542 User manual

System Board D2542

for RX100 S5

Technical Manual

Edition November 2009

Comments…Suggestions…Corrections…

The User Documentation Department would like to

know your opinion of this manual. Your feedback helps

us optimize our documentation to suit your individual

needs.

Feel free to send us your comments by e-mail to

[email protected].

Certified documentation

according to DIN EN ISO 9001:2000

To ensure a consistently high quality standard and

user-friendliness, this documentation was created to

meet the regulations of a quality management system

which complies with the requirements of the standard

DIN EN ISO 9001:2000.

cognitas. Gesellschaft für Technik-Dokumentation mbH

www.cognitas.de

Delivery subject to availability; right of technical modifications reserved.

All hardware and software names used are trademarks of their respective manufacturers.

D2542 (RX100 S5) Technical Manual

Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 CE Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.3 Environmental Protection . . . . . . . . . . . . . . . . . . . 11

3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.2 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.3 PCI bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.4 Screen resolution . . . . . . . . . . . . . . . . . . . . . . . 19

3.5 Temperature / system monitoring . . . . . . . . . . . . . . . 19

3.6 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3.7 Interfaces and connectors . . . . . . . . . . . . . . . . . . . 23

3.7.1 External ports . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3.8 Settings with jumpers . . . . . . . . . . . . . . . . . . . . . 26

4 Replacing the lithium battery . . . . . . . . . . . . . . . . . 27

Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

D2542 (RX100 S5) Technical Manual 5

1 Introduction

This technical manual describes the system board D2542, which is equipped

with one Intel®processor.

Further information about drivers is provided in the readme files on the hard

disk, on the supplied “ServerStart“ or “Update“ CDs.

You will find further information in the BIOS description.

Notational conventions

The meanings of the symbols and fonts used in this manual are as follows:

italics indicates commands, menu items, file and path

names or software programs

fixed font indicate system output on the monitor

semi-bold fixed

font

indicates values to be entered through the keyboard

[Key symbol] indicates keys according to their representation on the

keyboard

If capital letters are to be entered explicitly, then the

Shift key is shown, e.g. [SHIFT] - [A] for A.

If two keys need to be pressed at the same time, then

this is shown by placing a hyphen between the two key

symbols.

“quotation marks” indicates names and terms that are being empha-

sized.

Êindicates an operation that to be performed

VCAUTION! indicates warnings, which, if ignored, will endanger

your health, destroy the system or lead to the loss of

data.

Iindicates additional information, notes and tips

Table 1: Notational conventions

D2542 (RX100 S5) Technical Manual 7

2 Important notes

In this chapter you will find essential information regarding safety when working

with your server.

VCAUTION!

With the system board installed you must open the system to access the

system board. How to access the system board of your system is

described in the appropriate service supplement.

When handling the system board, refer to the specific notes on safety in

the operating manual and/or service supplement for the respective

server.

2.1 Notes on safety

VCAUTION!

●The actions described in these instructions should only be performed

by authorized, qualified personnel. Equipment repairs should only be

performed by qualified staff. Any failure to observe the guidelines in

this manual, and any unauthorized openings and improper repairs

could expose the user to risks (electric shock, fire hazards) and could

also damage the equipment. Please note that any unauthorized

openings of the device will result in the invalidation of the warranty

and exclusion from all liability.

●Transport the device only in the antistatic original packaging or in

packaging that protects it from knocks and jolts.

●Only install expansions that are allowed for the system board. If you

install other expansions, you may damage the requirements and rules

governing safety and electromagnetic compatibility or your system.

Information on which system expansions are suitable can be

obtained from the customer service centre or your sales outlet.

●The warranty expires if the device is damaged during the installation

or replacement of system expansions.

8 Technical Manual D2542 (RX100 S5)

Notes on safety Important notes

V●Components can become very hot during operation. Ensure you do

not touch components when making extensions to the system board.

There is a danger of burns!.

●Transmission lines to peripheral devices must be adequately

shielded.

●To the LAN wiring the requirements apply in accordance with the

standards EN 50173 and EN 50174-1/2. As minimum requirement

the use of a protected LAN line of category 5 for 10/100 MBps

Ethernet, and/or of category 5e for Gigabit Ethernet is considered.

The requirements of the specification ISO/IEC 11801 are to be

considered.

●Never connect or disconnect data transmission lines during a storm

(lightning hazard).

Batteries

VCAUTION!

●Incorrect replacement of lithium battery may lead to a risk of

explosion. The batteries may only be replaced with identical batteries

or with a type recommended by the manufacturer.

It is essential to observe the instructions in chapter “Replacing the

lithium battery”.

D2542 (RX100 S5) Technical Manual 9

Important notes Notes on safety

Modules with electrostatic-sensitive components

Systems and components that might be damaged by electrostatic discharge

(ESD) are marked with the following label:

Figure 1: ESD label

When you handle components fitted with ESDs, you must observe the following

points under all circumstances:

●You must always discharge yourself of static charges (e.g. by touching a

grounded object) before working.

●The equipment and tools you use must be free of static charges.

●Remove the power plug from the power socket before inserting or removing

boards containing ESDs.

●Always hold boards with ESDs by their edges.

●Never touch pins or conductors on boards fitted with ESDs.

●Use a grounding cable designed for this purpose to connect yourself to the

system unit as you install/deinstall the board.

●Place all components on a static-safe base.

IYou will find a detailed description for handling ESD components in the

relevant European or international standards (EN 61340-5-1,

ANSI/ESD S20.20).

10 Technical Manual D2542 (RX100 S5)

CE Certificate Important notes

Notes about boards

●During installation/deinstallation of the system board, observe the specific

instructions described in the service manual for the server.

●Remove the plug from the mains outlet so that system and system board are

totally disconnected from the mains voltage.

●To prevent damage to the system board, the components and conductors on

it, please take great care when you insert or remove boards. Take great care

to ensure that extension boards are slotted in straight, without damaging

components or conductors on the system board, or any other components,

for example EMI spring contacts

●Be careful with the locking mechanisms (catches, centring pins etc.) when

you replace the system board or components on it, for example memory

modules or processors.

●Never use sharp objects (screwdrivers) for leverage.

2.2 CE Certificate

The shipped version of this board complies with the requirements

of the EEC directive 2004/108/EC "Electromagnetic compati-

bility".

Compliance was tested in a typical PRIMERGY configuration.

Table of contents

Other Fujitsu Motherboard manuals

Fujitsu

Fujitsu D1271 User manual

Fujitsu

Fujitsu SK-96380-120PMT User manual

Fujitsu

Fujitsu D2119 User manual

Fujitsu

Fujitsu MB86R11 User manual

Fujitsu

Fujitsu D2151 User manual

Fujitsu

Fujitsu D2870 User manual

Fujitsu

Fujitsu MOTORKIT-91F267-MC User manual

Fujitsu

Fujitsu SK-MB9EF120-002 User manual

Fujitsu

Fujitsu QFP-100P User manual

Fujitsu

Fujitsu Siemens D1160 User manual

Fujitsu

Fujitsu D3011 User manual

Fujitsu

Fujitsu D3674 User manual

Fujitsu

Fujitsu D2109 User manual

Fujitsu

Fujitsu D2811 User manual

Fujitsu

Fujitsu D2831 User manual

Fujitsu

Fujitsu D2619-N User manual

Fujitsu

Fujitsu MB2146-450-E User manual

Fujitsu

Fujitsu FLASH-CAN-64P-350-PMC User manual

Fujitsu

Fujitsu D3433 User manual

Fujitsu

Fujitsu D3118 User manual

Fujitsu

Fujitsu MB91470 SERIES User manual

Fujitsu

Fujitsu D2156-S2 User manual

Fujitsu

Fujitsu D2863 User manual

Fujitsu

Fujitsu D2786 User manual

Popular Motherboard manuals by other brands

DFI

DFI SD170 user manual

ASROCK

ASROCK ROMED8-2T user manual

Asus

Asus P2L97A user manual

Winmate

Winmate IC70 user manual

Asus

Asus MES-B user manual

Grantech

Grantech SYS8F377VGGA-3OMN user manual

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR user guide

Gigabyte

Gigabyte GA-9IVDT user manual

Texas Instruments

Texas Instruments ADS8372EVM user guide

Commell

Commell MS-C73 user manual

IBT Technologies

IBT Technologies MB860 user manual

Nvidia

Nvidia TEGRA DG-04927-001_V01 user guide

Biostar

Biostar M7VIT Bravo Description

Intel

Intel D33217CK specification

Asus

Asus F1A55-M LX PLUS R2.0 user manual

EPC

EPC EPC9147C quick start guide

Asus

Asus EX-B760M-V5 D4 quick start guide

EPOX

EPOX MU-8KHA0010 user manual