Front Runner RRAC248 User manual
RRAC248_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
front runner
RRAC248
ENG
1
Thank you for purchasing a Front Runner Pro Water Tank Flat Mount Bracket.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the included components.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
PRO WATER TANK FLAT MOUNT BRACKET
RRAC248_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
2
TOOLS NEEDED
FIGURE 1.1
CHECK ONLINE FOR THE LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM
GET ORGANIZED
1
IN THE BOX
1 1 X Mounting Bracket
2 3 X M6 x 25 Button Head Screw
3 4 X M6 Jack Nut
4 1 X Jack Nut Tool
5 3 X M6 Nyloc Nut
6 3 X M6 x 19 x 1.2 Flat Washer
7 2 X PSA Strip PE60 (420mm)
8 1 X M6 x 30 Button Head Screw
2
1
3
6
5
8
4
7
Marker
10mm
13mm
24mm
4mm
5mm
4mm
6.5mm
12mm
Anti-
Rust
Denatured
Alchohol Sealant
Thread
Tape
RRAC248_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
3
FIT AND SECURE
2
2.1
2.2
2.3
Assemble A, B and C (supplied with
RRAC179) to the Mounting Bracket (Item 1).
D
D
A
B
1
C
8
3
4
5mm
13mm
Marker
4mm
6.5mm
12mm
4mm
Determine where the Pro Water Tank
(Sold Seperately) will be Mounted. Loosly
fit the Pro Tank Strap (Sold Seperately) and
Pro Water Tank (Sold Seperately) to the
Mounting Bracket (Item 1).
Mark holes (D) as shown.
Option A
Drill a 4mm Pilot hole and open to 6.5mm if
you want to Secure the Mounting Bracket
using M6 x 25 Button Head Bolt, M6 x 19 x
1.2 Flat Washer and M6 Nyloc Nuts (Items
2, 5 & 6).
Option B
Drill a 4mm Pilot hole and open to 12mm if
you want to Secure the Mounting Bracket
using M6 x 25 Button Head Bolts and M6
Jack Nuts (Items 2 & 3). Apply anti-rust
before 2.3.
Only Proceed with this step when using
mounting option B.
Insert an M6 x 30 Button Head Bolt (Item 8)
into the side of the Jack Nut Tool (Item 4).
Loosely fit a jack nut (Item 3) to the button
head bolt as shown.
Insert the Jack Nut (Item 3) into the 12mm
hole.
Using a cordless driver and a 4mm allen
cordless bit, set the jack nut into the hole
while holding onto the handle of the Jack
Nut Tool (Item 4).
Repeat for the other holes.
RRAC248_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
3
FIT AND SECURE
2
2.4
2.5
2.6
Place the PSA Strips (Item 7) below the Pro
Water Tank as shown in 2.5.
Clean the area using a rag and denatured
alcohol.
Remove the Backing and stick The PSA
Strips (Item 7) to the position identified
earlier.
If you are fitting the tap apply thread tape to
the thread of the tap.
This will allow the Tap to be aligned to your
chosen position and have a water tight seal.
Sold Seperately
Tap - WTAN059
Pro Water Tank / 42L - WTAN062
Pro Tak Strap - RRAC179
4mm
10mm
Sealant
Anti-
Rust
Denatured
Alchohol
Thread
Tape
24mm
Apply anti-rust around all the holes. Place
some silicone around each hole.
Option A
Secure the Pro Tank Strap (Sold Seperately)
and the Mounting Bracket (Item 1) using
M6 x 25 Button Head Bolt, M6 x 19 x 1.2 Flat
Washers and M6 Nyloc Nuts (Items 2, 5 & 6).
Option B
Secure the Pro Tank Strap (Sold Seperately)
and the Mounting Bracket (Item 1) using M6
x 25 Button Head Bolts (Item 2).
RRAC248_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
4
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
3
Congratulations! You did it. Take a step back and admire your work!
Table of contents
Other Front Runner Automobile Accessories manuals
Front Runner
Front Runner RRAC054 User manual
Front Runner
Front Runner RRAC203 User manual
Front Runner
Front Runner SLIMPRO KVXS006 Manual
Front Runner
Front Runner SLIMLINE II User manual
Front Runner
Front Runner GOFR001 User manual
Front Runner
Front Runner PBTT002 User manual
Front Runner
Front Runner JADA014 User manual
Front Runner
Front Runner SLIMLINE II TRAY User manual
Front Runner
Front Runner STRA057 User manual
Front Runner
Front Runner TRCA005 User manual
Front Runner
Front Runner FAJL002 User manual
Front Runner
Front Runner SSDR003 User manual
Front Runner
Front Runner RRAC201 User manual
Front Runner
Front Runner GBHO012 User manual
Front Runner
Front Runner Drawer 6 Box Large MKII SSWO008 User manual
Front Runner
Front Runner SSDS115 User manual
Front Runner
Front Runner FAJK002 Instruction Manual
Front Runner
Front Runner Slimline II KRVA002T User manual
Front Runner
Front Runner FAMG001 User manual
Front Runner
Front Runner LADD007 User manual
