Front Runner PBTT002 User manual
ENG
PBTT002_REV_A00 © 2023 FRONT RUNNER VEHICLE OUTFITTERS
1
Don’t be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain
aspects of your warranty.
Before you begin, take a moment and open all your Front Runner Rack Kit boxes and gather the assembly instructions for the various components.
A complete kit will contain:
1. Front Runner Mounting System specific to your vehicle
2. Front Runner Rack Tray or Load Bar Slats
This document will guide you through the assembly of the Mounting System and assist you in fitting the Rack tray or Load Bars to your specific vehicle.
Please refer to the next page for a list of all the components, quantities and tools required.
PBTT002
READ ME FIRST
START HERE!
front runner TOYOTA TUNDRA 3RD GEN CREWMAX 5.5FT
PRO BED RACK MOUNTING SYSTEM
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
PBTT002_REV_A00 © 2023 FRONT RUNNER VEHICLE OUTFITTERS
2
TOOLS NEEDED
CHECK ONLINE FOR LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM
GET ORGANIZED
1
IN THE BOX PBTT002
1 1 X LH BED STIFFENER
2 2 X REAR TOP MAIN BRACKET
3 4 X REAR BRACKET GUSSET
4 8 X M8 X 16 BUTTON HEAD SCREW
5 18 X M8 NYLOC NUT
5mm
6 12 X M8 NUT CAP
7 1 X RH BED STIFFENER
8 1 X FRONT LH CHANNEL MOUNT
9 1 X FRONT RH CHANNEL MOUNT
10 12 X M8 X 19 X 2 FLAT WASHER
IN THE BOX PBTT002
14 2 X M8 CHANNEL PLATE
15 4 X M8 X 25 CARRIAGE BOLT
16 4 X M8 X 16 X 1.6 FLAT WASHER
17 2 X 10mm BED SPACER
18 2 X 6mm BED SPACER
19 2 X M12 FLAT WASHER
20 2 X M12 X 120 HEX BOLT
21 2 X M12 NUT CAP
22 4 X M8 x 25 BUTTON HEAD BOLT
11 6 X M8 X 25 HEX BOLT
12 4 X M8 X 20 BUTTON HEAD SCREW
13 4 X M8 X 19 X 3 FLAT WASHER
2
1
3
4
5
6
7
8 9
10
11
12
13
14
15
16
17
18
20
19
21
22
4mm
13mm
10mm
19mm
13mm
10mm
9mm
4mm
PBTT002_REV_A00 © 2023 FRONT RUNNER VEHICLE OUTFITTERS
3
TOOLS NEEDED
CHECK ONLINE FOR LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM
GET ORGANIZED
1
IN THE BOX PBRA001
1 4 X PRO BED RACK LEG
2 2 X PRO BED RACK REAR BRACE
3 2 X PRO BED RACK RH REAR WING BRACKET
4 2 X PRO BED RACK TOP TRUSS
5 1 X PRO BED RACK RH FRONT DIAGONAL BRACE
2
6 1 X PRO BED RACK LH FRONT DIAGONAL BRACE
7 12 X M6 x 16 BUTTON HEAD SCREW
8 24 X M6 NYLOC NUT
9 22 X M6 NUT CAP
10 16 X M8 x 20 BUTTON HEAD SCREW
11 16 X M8 x 19 x 2 FLAT WASHER
12 16 X M8 NYLOC NUT
13 16 X M8 NUT CAP
IN THE BOX PBRA001
14 6 X M6 x 12 BUTTON HEAD SCREW
15 2 X FRONT HORIZONTAL BRACE
16 1 X FRONT CENTER BRACE
17 4 X M6 x 20 BUTTON HEAD SCREW
18 9 X M6 x 12 x 1 FLAT WASHER
19 24 X M6 x 25 THREAD FORMING SCREW
20 1 X T30 6" TORX BIT
1
3
4
5
6 7
8
9
10
11
12
13
14
15
16
17
18 19
20
FRONT
Oil or
Anti Seize
Torx
T30/T55
5mm
4mm
13mm
10mm
PBTT002_REV_A00 © 2023 FRONT RUNNER VEHICLE OUTFITTERS
4
TOOLS NEEDED
CHECK ONLINE FOR THE LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM
GET ORGANIZED1
IN THE BOX PBAL_1450
1 2 X TOP EXTRUSION
2 1 X TOP MIDDLE EXTRUSION
3 2 X BOTTOM EXTRUSION
4 2 X 1450mm PSA STRIP PE60
Friend
33
33
32
31
31
34
34
© 2023 FRONT RUNNER VEHICLE OUTFITTERS
6
PBTT002_REV_A00
FIT AND SECURE
2
2.1
2.2
2.3
Remove the factory rail end caps.
Slide 2 channel plates (Item 14) into each rail
Loosly assemble the Front Mount Brackets
(item 9) using the carriage bolts, M8x16x1.6
Flat washer and M8 Nyloc Nut (Item 15,16 &
5).
Do this on both the LH and RH side
Note LH and RH Front Channel mount position
DO NOT FULLY TIGHTEN
Assemble the Pro Bed Leg (Item 1) to the
Front Channel Mount (Item 9) using M8x25
Button head screw,M8x19x3 Flat Washer and
M8 Nyloc Nut (Item 22,13 & 5) as shown and
M8x20 Button head screw and M8 nyloc Nut
(Item 12 & 5).
Do this on both the LH and RH side
DO NOT FULLY TIGHTEN
Assemble the Front Diagonal and Horizontal
Brace parts as shown (Item 4,5 & 6) to the
legs fitted in 2.2 using the M8x20 Button
head screws,M8x19x2 Flat washer and M8
Nyloc Nut (Item 10,11 &12).
FULLY TIGHTEN.
Use the M6x20 Button head Screws,M6x12x1
Flat washer and M6 Nyloc Nut (Item 8,17 &
18)to fit the Front Center Brace to the LH and
RH Front Horizontal Braces (Item 16).
DO NOT FULLY TIGHTEN
12
22
13
1
5
6
1515
14
15
16 5
9
13mm
5mm
10
4
7
6
5
11
12
13
18
8
16
17
© 2023 FRONT RUNNER VEHICLE OUTFITTERS
6
PBTT002_REV_A00
FIT AND SECURE
2
2.4
2.5
2.6
Slide the front leg and truss assembly back-
ward to allow access for securing extrusions.
Using the supplied T30 6" torx bit and a
cordless driver fit the extrusion using the
M6x25 thread forming screws (Item 19).Use
a slow and constant speed when using the
cordless driver.
When complete slide assembly forward in
the cargo rails giving room for rear legs to
be assembeld.
Remove the 2 rear factory bed bolts using a
T55 Torx Bit.
Position the rear Bed Stiffener's by the rear
bed pillars, aligning the base hole over the
hole of the M12 bolt removed earlier
Mark the 3 holes on both LH and RH stiffener
brackets.Remove both the rear tail lights
(check on Youtube for help). Drill the 3 holes
using a 4mm as a pilot hole and open all up
to 9mm.Use anti rust on the Holes.
Place the 6mm and 10mm bed spacer (Item
17&18) over the bed bolt hole.Loosely
fit the M12 bed bolt and M12 Flat
washer (Item 19&20) before inserting
and fully tightening the two M8x25 Hex
Bolts,M8x19x2 Flat Washer and M8 Nyloc
Nut (Item10,11&5).When done Fully tighten
the M12 bed bolt.Place the M12 Nut cap
(Item 21) to the M12 Hex Bolt.
Assemble the Pro Bed Rack Leg (Item 1) to
the rear top main bracket (Item 2) using the
rear gusset (item 3) and M8x16 Button head
screw and M8 nyloc Nut as shown.
Assemble the M8x20 Button head screw and
M8 Nyloc Nut (Item 12&5) and fully tighten all
the bolts.
5mm
18
17
1
11
20
5
10
19
21
1
3
2
12 17
4
5
6
Torx
T30
Cordless
Drill
Oil or
Anti Seize
19
1
2
3
TOP EXTRUSION
LH RH
Take note of extrusion orientation !
Use a little anti seize or oil on screw
threads before inserting. Note these are
Thread Forming Screws.
Tightening Torque 25Nm / 18.4 ft lbs
13mm
19mm
13mm
13mm
Tightening Torque:
M8 : 15-20Nm / 11.06 ft lb - 14.75 ft lb
Torx
T55
10
11
12
13
© 2023 FRONT RUNNER VEHICLE OUTFITTERS
7
PBTT002_REV_A00
FIT AND SECURE
2
2.7
2.8
2.9
Fit the leg assembly to the bed stiffener
installed earlier using the M8x25 Hex Bolt,
M8x19x2 Flat Washer and M8 Nyloc Nut (Item
10,11&5).
Fit the M8x16 Button Head screws as shown
into the side of the brackets together with
the M8 Nyloc nuts (Item 4&5).
Fully tighten all the bolts on the leg assembly
and place nut caps where needed.
REFIT BOTH REAR TAIL LIGHTS.
Fit the Rear Brace (Item 2) using the M6x12
button head screws and M6 Nyloc nuts (Item
14 & 8).
Fully tighten and place M6 Nut caps (Item 9)
on the M6 Nyloc Nuts.
Loosely assemble the rear top truss using
the M8x20 Button head screws, M8x19x2
Flat washer and M8 Nyloc Nuts (Item
10,11&12).Fully tighten the M8 Button Heads
and place M8 Nut Caps on the M8 Nyloc Nuts
(Item 13).
7
6
11
10
4
5
Tightening Torque:
M8 : 15-20Nm / 11.06 ft lb - 14.75 ft lb
13mm
5mm
Tightening Torque:
M8 : 15-20Nm / 11.06 ft lb - 14.75 ft lb
14
8
9
2
13mm
5mm
Tightening Torque:
M6 : 8-10Nm / 5.9 ft lb - 7.38 ft lb
19
16
5 6
© 2023 FRONT RUNNER VEHICLE OUTFITTERS
8
PBTT002_REV_A00
FIT AND SECURE
2
2.10
2.11
2.12
Pull the front leg / truss / extrusion assembly
toward the rear legs. Attach the rear leg
assembly to the Extrusions using the M6x25
thread forming screws (Item 19) and a
cordless driver.The front assembly will be
pulled back into its final position while fully
tightening these screws.
With the Load Bed rack in Position fully
tighten the bracket fitted in 2.1.
Place M8 Nut caps (Item 6) onto the M8 Nyloc
nuts (Item 5).
13mm
Using clamps and a spirit level clamp the
spirit level to the inside of the Front Center
Brace and Tighten the M6x20 Button head
screws and M6 Nyloc Nuts fitted in 2.3.
Place M6 Nut caps on the M6 Nyloc Nuts.
Use a little anti seize or oil on screw
threads before inserting. Note these are
Thread Forming Screws.
Tightening Torque 25Nm / 18.4 ft lbs
Torx
T30
Cordless
Drill
Oil or
Anti Seize
Tightening Torque:
M8 : 15-20Nm / 11.06 ft lb - 14.75 ft lb
4mm
10mm
© 2023 FRONT RUNNER VEHICLE OUTFITTERS
9
PBTT002 _REV_A00
FIT AND SECURE
2
2.13
2.14
Assemble the Rear Wing Brackets (Item 3)
using the M6x12 Button head screws and M6
Nyloc Nuts (Item 14 & 8).
Place the M6 Nut caps (Item 9) over the nyloc
nuts.
Fully tighten all the bolts and nuts and place
nut caps where needed.
13mm
5mm
3
8
9
14
COMPLETION
6
6.1
Congratulations! You did it. Take a step back and admire your work!
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
7
Now's the time to visit your favorite Front Runner dealer in person or online.
IMPORTANT!
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY ARE MOUNTED TO. PLEASE REFER TO YOUR SPECIFIC VEHICLE MANUFACTURER
FOR A RECOMMENDED ROOF RATING. FRONT RUNNER CANNOT BE RESPONSIBLE FOR IMPROPER LOADING BEYOND THE VEHICLE MANUFACTURER'S STATED LOAD CAPACITY.
4
© 2023 FRONT RUNNER VEHICLE OUTFITTERS
10
PBTT002_REV_A00
Other Front Runner Automobile Accessories manuals
Front Runner
Front Runner RRAC202 User manual
Front Runner
Front Runner SLIMLINE II KRFE009T Manual
Front Runner
Front Runner TRCA008 User manual
Front Runner
Front Runner FAJK007 User manual
Front Runner
Front Runner SlimSport KSFR002 User manual
Front Runner
Front Runner MKIII Small User manual
Front Runner
Front Runner SLIMLINE II User manual
Front Runner
Front Runner SSAM009 User manual
Front Runner
Front Runner SLIMLINE II TRAY User manual
Front Runner
Front Runner LAVT003 User manual
Front Runner
Front Runner Wolfpack Pro RRAC257 User manual
Front Runner
Front Runner SSBS008 User manual
Front Runner
Front Runner SSDR011 User manual
Front Runner
Front Runner TRFD001 User manual
Front Runner
Front Runner RRAC242 User manual
Front Runner
Front Runner TBMK011 Instruction Manual
Front Runner
Front Runner TBMK009 User manual
Front Runner
Front Runner FATF006 User manual
Front Runner
Front Runner TOYOTA 4RUNNER User manual
Front Runner
Front Runner SSDS110 User manual
