Frigidaire FAH146R2T1 User manual

Installatio Instructions

14,000 TU TTW

Do This First

(for existing sleeve)

Note that the air conditioner dimensions are: 24" wide,

14½" high, and 22" deep (without front). Install Air

Conditioner according to these installation instructions

to achieve the best performance. Save these installation

instructions for future reference.

CAUTION: When installation is complete, replacement

unit MUST have a rearward

slope as shown.

REAR

1/4" to 5/16"

Walt

Sleeve _

UNIT

LEVEL

Items in Kit

You may not need att parts in the kit. Discard unused

parts.

Tapered Spacer Blocks

Centering/Support Blocks

Plastic Divider

Stuffer Seat

Seal

Trim Frame (side legs)

Trim Frame (top & bottom legs)

Ground Wire (green)

Nut for grounding screw

Grounding Screw

Grille (plastic)

Grille Aluminum

Nuts (plastic)

Screw w/washer

How to Install

17" Long

4½"x 3½"x 1½"

1/8" x 4'A"x 14½"

1 "x 1½"x 84"

11/_"x 1½"x 25"

1½"x 1½"x 14"

1½"x 3/8"x 25"

11A"x 3/8"x 14"

1" x 3/4"x 14"

1. Identify the wall-sleeve brand for your installation,

from the chart below.

Brand

White-Westinghouse

Frigidaire

Carrier (52F Series)

General Electric/

Hotpoint

Whirlpool

Qty.

Wall Sleeve Dimensions

(inches)

Width Height Depth

}25½ 15_A 17½

16,

or 22

26 15%

257A 16½ 16Y_

17,A

or 23

16%

or 19_A

18%

16_/,

Fedders/Emerson 27 163/,

Sears/Kenmore 25% 167A

Emerson/Fedders 263A 15%

Carrier (51S Series) 253A 16½

Friedrich 27 16%

NOTE: All wall sleeves used to mount the new Air

Conditioner must be in sound structural condition and

have a rear grille that securely attaches to sleeve, or

rear flange that serves as a stop for the Air Conditioner.

2. Remove old Air Conditioner from wall sleeve and

prepare wall sleeve as follows:

-- Clean interior (do not disturb seals).

-- Wall sleeve must be securely fastened in wall before

installing Air Conditioner. Drive more nails or screws

through sleeve, into wall, if needed.

-- Repair paint if needed.

3. If not existing, drill a 3/16"clearance hole for ground-

ing screw through left side of wall sleeve, in a clear area

about 3 inches maximum (to suit) back from front edge

of sleeve as shown below. Next attach ground wire inside

sleeve, using grounding screw, nut washer pull loose

end of ground wire out front of sleeve, and temporarily

bend it down and around lower edge of sleeve.

Wall sleeve to unit " Ih'"_ 3/16"

sleeve grounding _ - Hole

4. Prepare the wall sleeve for installation of the new unit

per the following Brand instructions.

#1 Emerson 15" Deep

#2 Fedders 19_" Deep

#3 Fedders or Friedrich 16%" Deep

#4 General Etectric/Hotpoint 16_" Deep

#5 Sears or Carrier (51S Series) 18%" Deep

#6 Whirlpool 17'A" Deep

#7 Whirlpool 23" Deep

#8 White-Westinghouse/Frigidaire/ 16"+ 17½"Deep

Carrier (52F Series)

#9 White-Westinghouse/Frigidaire 22" Deep

5. Install new unit into wall sleeve.

6. To attach ground wire to the new unit, remove the

screw from the left side front.

7. Assemble and install the

Trim Frame (see instruction).

P/N 66121624

This units increased performance characteristics meant;

1. The rear air intake moved to the opposite side.

2. The depth had to be increased.

It is very important that these installation instructions are followed so your unit can operate at maximum

efficiency.

If this is an existing sleeve, and there is an existing rear grille, the louvers will have to be bent as per the

instructions at the beginning of each section.

If this proves too difficult to accomplish;

EITHER

1. Remove the existing grille.

2. Place the included aluminum grille towards the rear of the unit.

3. Mark through the hole positions.

4. Drill through the sleeves flanges with a 1/8" drill bit.

5. Attached the new grille with self-threading screws and washers (not included).

6. It is VERY IMPORTANT that the partition be placed on the left side of the sleeve as shown below.

1. Remove the existing grille.

2. Use Plastic grille and secure to sleeves flanges using existing screws and washers.

Wall Sleeve Brands: #1 Emerson 15"Deep

Rear.Louvers _60_ '

II I IIII I I IIIIIIIII

Top View

1. Redirect the louvers at the back of the wall sleeve as shown

opposite. The use of pliers is recommended.

2. Attach (1) 1 W' x 3/8" x 25" long seal in the center at the

top of the sleeve. Remove the backing paper and press

into position.

3. Attach (2) 1 W' x 3/8" x 14" seals to the left and right sides

of the sleeve.

4. Cut the 1 W' x 3/8" x 25" long seal to 14" long and attach

it to the vertical section of the rear grille as shown.

5. Attach (2) 4 W' x 3 W' x 1 W' centering/support blocks

one on each side wall. Place in center of side wall with

the tapered end facing the opening.

6. Gently slide unit into sleeve.

7. Before sliding all-the-way back, remove 2nd screw from

front on left side of unit.

8. Remove the plastic washer from the screw.

9. Screw and attach the other end of the ground wire to

the unit as shown in picture. Make sure that the toothed

washer is against the cabinet.

10. Slide the unit completely to the rear to ensure a good

seal, making sure the ground wire does not become

tangled.

11. Seal & Frame the unit as described on the last page of

these instructions.

Wall Sleeve Brands: #2 Fedders 193A '' Deep

Rear,_Louvers _60_ '

II IIIIII I IIIIIIIII

Top View

1. Redirect the louvers at the back of the wall sleeve as shown

opposite. The use of pliers is recommended.

2. Attach (2) 4 W'x 3W' x 1 W' centering/support blocks one

on each side wall. Place in center of side wall with the

tapered end facing the opening.

3. Cut (2) 17" Tapered Spacer Blocks as shown below into

two pieces. 17,,.

3/4" pered Spacer Block

Cut Here i _ \ --Protection Paper Backing

4. The 4" section is placed in front of the rib on base with the

tapered end facing the back of the sleeve. The remaining

portion will be placed behind the rib again sloping toward

the rear of the sleeve. This helps induce a rearward slope

on the unit.

5. Attach (1) 1 W' x 3/8" x 25" long seal in the center at the

top of the sleeve. Remove the backing paper and press

into position.

6. Attach (2) 1 W' x 3/8" x 14" seals to the left and right sides

of the sleeve.

7. Cut the 1 W' x 3/8" x 25" long seal to 14" long and attach it

to the vertical section of the rear grille as shown.

8. Gently slide unit into sleeve.

9. Before sliding all-the-way back, remove 2nd screw from

front on left side of unit.

10. Remove the plastic washer from the screw.

11. Screw and attach the other end of the ground wire to

the unit as shown in picture. Make sure that the toothed

washer is against the cabinet.

12. Slide the unit completely to the rear to ensure a good seal,

making sure the ground wire does not become tangled.

13. Seal & Frame the unit as described on the last page of

these instructions.

Wall Sleeve Brands: #3 Fedders or Friedrich 16 ¾" Deep

Rear,_Louvers _60_ '

II IIIIII I IIIIIIIII

Top View

1. Redirect the louvers at the back of the wall sleeve as shown

opposite. The use of pliers is recommended.

2. Attach (2) 4 W'x 3W' x 1 W' centering/support blocks one on

each side wall. Place in center of side wall with the tapered

end facing the opening.

3. Cut (2) 17" Tapered Spacer Blocks as shown below into three

17" I

pieces, i,, ,,..

Ii Ta e s aoer ,,oo

I E

Cut Hero I 12-1/2" _ 2-1/2 Protection Paper Backing

4. The 2 W' section is placed in front of the rib on base with the

tapered end facing the back of the sleeve. Cut the remaining

portion to 12 W' and place behind the rib again sloping toward

the rear of the sleeve. This helps induce a rearward slope on

the unit.

5. Attach (1) 1 W' x 3/8" x 25" long seal in the center at the

top of the sleeve. Remove the backing paper and press

into position.

6. Attach (2) 1 W' x 3/8" x 14" seals to the left and right sides

of the sleeve.

7. Cut the 1 W' x 3/8" x 25" long seal to 14" long and attach it

to the vertical section of the rear grille as shown.

8. Gently slide unit into sleeve.

9. Before sliding all-the-way back, remove 2nd screw from front

on left side of unit.

10. Remove the plastic washer from the screw.

11. Screw and attach the other end of the ground wire to the

unit as shown in picture. Make sure that the toothed washer

is against the cabinet.

12. Slide the unit completely to the rear to ensure a good seal,

making sure the ground wire does not become tangled.

13. Seal & Frame the unit as described on the last page of

these instructions.

Wall Sleeve Brands: #4 General Electra/Hotpoint 16 7/8" Deep

Rear,_Louvers _60_ '

II IIIIII I IIIIIIIII

Top View

1. Redirect the louvers at the back of the wall sleeve as shown

opposite. The use of pliers is recommended.

2. Cut (2) 17" Tapered Spacer Blocks as shown below into two

pieces. 17" ,

[_ Tapered Spacer Block ir_,_ 1" Cut Here

] _h.]

\v-,

--Protection Paper Backing

3. Install as shown with the tapered end W' from the back of the

sleeve. This helps induce a rearward slope on the unit.

4. Attach (1) 1 W' x 3/8" x 25" long seal in the center at the top

of the sleeve. Remove the backing paper and press into

position.

5. Attach (2) 1 Y2" x 3/8" x 14" seals to the left and right sides

of the sleeve.

6. Cut the 1 W' x 3/8" x 25" long seal to 14" long and attach it

to the vertical section of the rear grille as shown.

7. Center unit & gently slide unit into sleeve.

8. Before sliding all-the-way back, remove 2nd screw from front

on left side of unit.

9. Remove the plastic washer from the screw.

10. Screw and attach the other end of the ground wire to the

unit as shown in picture. Make sure that the toothed washer

is against the cabinet.

11. Slide the unit completely to the rear to ensure a good seal,

making sure the ground wire does not become tangled.

12. Seal & Frame the unit as described on the last page of

these instructions.

Wall Sleeve Brands: #5 sears or carrier 51s series 18 5/8" Deep

Rear,_Louvers _60_ '

II IIIIII I IIIIIIIII

Top View

1. Redirect the louvers at the back of the wall sleeve as shown

opposite. The use of pliers is recommended.

2. Install (2) tapered spacer blocks to the floor of the sleeve as

shown. DO NOT CUT THESE BLOCKS. This helps induce

a rearward slope on the unit.

3. Install as shown with the tapered end W' from the back of the

sleeve. This helps induce a rearward slope on the unit.

4. Attach (1) 1 W' x 3/8" x 25" long seal in the center at the top

of the sleeve. Remove the backing paper and press into

position.

5. Attach (2) 1 W' x 3/8" x 14" seals to the left and right sides

of the sleeve.

6. Cut the 1 W' x 3/8" x 25" long seal to 14" long and attach it

to the vertical section of the rear grille as shown.

7. Center unit & gently slide unit into sleeve.

8. Before sliding all-the-way back, remove 2nd screw from front

on left side of unit.

9. Remove the plastic washer from the screw.

10. Screw and attach the other end of the ground wire to the

unit as shown in picture. Make sure that the toothed washer

is against the cabinet.

11. Slide the unit completely to the rear to ensure a good seal,

making sure the ground wire does not become tangled.

12. Seal & Frame the unit as described on the last page of

these instructions.

Wall Sleeve Brands: #6 Whirlpool 17 1/8" Deep

Rear,_Louvers _60_ '

II IIIIII I IIIIIIIII

Top View

1. Redirect the louvers at the back of the wall sleeve as shown

opposite. The use of pliers is recommended.

2. Cut (2) 17" Tapered Spacer Blocks as shown below into

two pieces. 17.

Cut Here i _ \ y __

-- Protection Paper Backing

3. Install to the floor of the sleeve as shown. This helps

induce a rearward slope on the unit.

4. Attach (1) 1 W' x 3/8" x 25" long seal in the center at the

top of the sleeve. Remove the backing paper and press

into position.

5. Attach (2) 1 W' x 3/8" x 14" seals to the left and right

sides of the sleeve.

6. Cut the 1 W' x 3/8" x 25" long seal to 14" long and attach it

to the vertical section of the rear grille as shown.

7. Center unit & gently slide unit into sleeve.

8. Before sliding all-the-way back, remove 2nd screw from front

on left side of unit.

9. Remove the plastic washer from the screw.

10. Screw and attach the other end of the ground wire to the

unit as shown in picture. Make sure that the toothed washer

is against the cabinet.

11. Slide the unit completely to the rear to ensure a good seal,

making sure the ground wire does not become tangled.

12. Seal & Frame the unit as described on the last page of

these instructions.

Wall Sleeve Brands: #7Whirlpool 23, Deep

Rear,_Louvers _60_ '

II IIIIII I IIIIIIIII

Top View

1. Redirect the louvers at the back of the wall sleeve as shown

opposite. The use of pliers is recommended.

Because of the increased unit depth, first try dry fitting

using the method described below:

1. Place (2) 1 W'x 1W' x 14" seals against each side.

2. Gently slide unit in and check if amount extending from the

sleeve is sufficient once the trim frame is attached.

3. If position is okay, remove unit and Proceed to the next step.

If not go to step 8.

4. Attach (1) 1 W' x 1 W' x 25" long seal in the center at the

top of the sleeve. Remove the backing paper and press into

position.

5. Attach (2) 1 W' x 1 W' x 14" seals to the left and right sides

of the sleeve.

6. Cut the 1 W' x 1 W' x 25" long seal to 14" long and attach it

vertically to the rear grill 7" from the left side.

7. Attach the tapered spacer blocks to the floor of the sleeve.

Now go to step 13.

Use these next steps if the unit requires extra extension

into the room.

8. Attach 1" x 3_,,x 14" long seal over the solid vertical portion

of the rear grille.

9. Attach (2) 4 W'x 3W' x 1 W' foam blocks with the slot

overlapping the seal above.

10. Install the divider into the slots of the foam blocks. You may

need to trim the length to size.

11. Cut the 1 W' x 1 W' x 25" seal to fit the top of the sleeve.

The pieces must be fitted flush to the edge of the divider.

12. Attach (2) 1 W' x 1 W' x 14" seals along the sides of the

sleeve again making sure all seals are flush.

13. Center unit & gently slide unit into sleeve.

14. Before sliding all-the-way back, remove 1st screw from

front on left side of unit.

15. Remove the plastic washer from the screw.

16. Screw and attach the other end of the ground wire to the

unit as shown in picture. Make sure that the toothed washer

is against the cabinet.

17. Slide the unit completely to the rear to ensure a good seal,

making sure the ground wire does not become tangled.

18. Seal & Frame the unit as described on the last page of

these instructions.

Wall Sleeve Brands: #8 White Westinghouse/Frigidaire/ 16" + 17 1/2" Deep

Carrier 52F Series

,If the wall sleeve does not have a rear grille or Iouvered

panel, install the plastic grille from the kit. The plastic

grille is mounted to the inside of the wall sleeve at the rear

flanges. There are (4) plastic nuts in the flanges of the wall

sleeve. If some are missing replacements are included in

the accessory kit, and can be simply pressed into the square

holes in the flanges. Place the grille against the rear flanges

and use the (4) large washers and screws to secure the grille.

2. Attach (1) 1 W' x 3/8" x 25" long seal in the center at the top

of the sleeve. Remove the backing paper and press into

position.

3. Attach (2) 1 Y2"x 3/8" x 14" seals to the left and right sides

of the sleeve.

4. Attach 1" x 3A,,14" long seal vertically 7" from the left side

of the sleeve.

5. Center unit & gently slide unit into sleeve.

6. Before sliding all-the-way back, remove 2nd screw from front

on left side of unit.

7. Remove the plastic washer from the screw.

8. Screw and attach the other end of the ground wire to the

unit as shown in picture. Make sure that the toothed washer

is against the cabinet.

9. Slide the unit completely to the rear to ensure a good seal,

making sure the ground wire does not become tangled.

10. Seal & Frame the unit as described on the last page of

these instructions.

This manual suits for next models

Table of contents

Other Frigidaire Air Conditioner manuals

Frigidaire

Frigidaire FRA064VU1 Installation instructions

Frigidaire

Frigidaire FRA103BT1 User manual

Frigidaire

Frigidaire FHWC084WB1 User manual

Frigidaire

Frigidaire FAH106S1T - 10000 BTU Through-the-Wall Air... User manual

Frigidaire

Frigidaire 220218A007 User manual

Frigidaire

Frigidaire CRA073PU113 User manual

Frigidaire

Frigidaire FAA065N7A User manual

Frigidaire

Frigidaire FAS297Q2A2 User manual

Frigidaire

Frigidaire FAH12EJ2T1 User manual

Frigidaire

Frigidaire FAH086S1T - Through The Wall Room Air... User manual

Frigidaire

Frigidaire FRA052XT7 Owner's manual

Frigidaire

Frigidaire FRA106BU1 Quick start guide

Frigidaire

Frigidaire FAC065J7A1 User manual

Frigidaire

Frigidaire FRS12PYW10 Owner's manual

Frigidaire

Frigidaire FRA186MT2 User manual

Frigidaire

Frigidaire FAK123J1V1 User manual

Frigidaire

Frigidaire FRA102BT1 User manual

Frigidaire

Frigidaire FAH08ES1T - 8,000 BTU Through-the-Wall Room Air... User manual

Frigidaire

Frigidaire FAA065P7 User manual

Frigidaire

Frigidaire FAC054J7A1 User manual

Frigidaire

Frigidaire FAA063P7A16 User manual

Frigidaire

Frigidaire CRA065AT7 Owner's manual

Frigidaire

Frigidaire FAS254J2A2 User manual

Frigidaire

Frigidaire FAZ12ES2A User manual

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Samsung

Samsung AS09HM3N user manual

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual

Webasto

Webasto Frigo Top 25 DS Instructions for use

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB operating instructions