Festo SPC11 Series User manual

Quick reference

Soft Stop

type SPC11-...

– English

8103866

2018-12b

[8103868]

Soft Stop SPC11

US patent no. 6,085,632

Festo SPC11 2018-12b2

Translation of the original instructions

Documentation on the product

For all available product documentation

èwww.festo.com/pk

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Germany

Internet: http://www.festo.com

E-Mail: service_international@festo.com

Reproduction, distribution or sale of this document or communication of

its contents to others without express authorization is prohibited.

a patent, utility model or design patent is registered.

English 3............................................

Festo SPC11 2018-12b English 3

1 User instructionsEnglish

The Soft Stop type SPC11-... is intended for fitting into a

machine or an automation system. In conjunction with

permitted drives and measuring systems, as well as with a

proportional directional control valve type MPYE-5-..., the

SPC11 permits fast movement into two end positions set

with fixed stops as well as into one or two mid-positions.

Note

This brief summary is intended only for users who are

familiar with the SPC11. Please observe the safety in

structions as well as the information on the permitted

combinations of valves, drives and measuring systems.

These can be found in the System manual for the SPC11

(type P.BE-SPC11-SYS-...) and in the associated “Drive-

specific supplement”.

Caution

Always switch on the operating voltage supply first and

then the compressed air supply.

Before carrying out installation and/or maintenance

work, switch off the following power supplies either

simultaneously or in the following sequence:

1. compressed air supply

2. operating voltage for the SPC11.

Festo SPC11 2018-12b English4

2 Connecting and display elements

12 3

1Control: operating voltage

connection and I/O coupling

2Valve: Valve connection

3Display

4Operating buttons

5Type plate

6Groove for identification

signs (type IBS 6x10)

7Measuring system

connection (here type

SPC11-POT-TLF)

8Earth (ground) connection

Festo SPC11 2018-12b English 5

3 Fitting and pneumatic installation

Mount the SPC11 on a flat surface. Use at least 3 screws

(M4) to fasten it.

Compressed air / service unit

S5 to 7 bar, dry, non-lubricated, 5 μm filter cartridge.

SFor good positioning behaviour, the compressed air on

the MPYE-5-...: must not fluctuate more than ± 1 bar.

SSufficient standard flow (reference value: twice the

standard flow of the valve).

SUse a microfilter if slight oil mist cannot be avoided.

Proportional directional control valve (type MPYE-5-...)

SThis should be fitted and connected up symmetrically

to the centre of the drive. If fitted to moving parts, the

MPYE-5-... must be mounted at right angles to the

direction of movement.

SFit silencers with large rated flow (e.g. U-1/8), length

of tubing max. 1 m.

Compressed air tubing and screw connectors

SThe tubing for the valve drive must be symmetrical.

With linear drives: tubing length = drive length

Festo SPC11 2018-12b English6

SThe dimensions refer to the standard sizes of service

units, proportional directional control valves and

drives.

SIf angled connectors cannot be avoided, use plug

connectors from the Quick Star series.

SDo not use any restrictors in the supply lines.

Drive and measuring system

SUse only the permitted combinations of valves, drives

and measuring systems approved of by Festo for the

SPC11.

SObserve the permitted fitting positions.

SMount the measuring system symmetrical to the drive

stroke.

SMount the drive, the guide and the measuring system

free of play and flush in the direction of movement.

Specially for drives type DGP(I)(L)-...-...-KF or DGP-... with

suitable guide):

SWith bilateral air supply, open up completely the ad

justing screws for the internal end position cushioning.

SUse a measuring system with the same stroke length.

Festo SPC11 2018-12b English 7

Specially for measuring systems type MLO-POT-...-TLF:

SMount the measuring system so that it is electrically

isolated.

SIf the measuring system is to be used in a dusty or

dirty environment, mount it so that the actuator slide

faces downwards.

Specially for measuring systems type MLO-POT-...-LWG:

SIn order to earth the system, connect the earth/ground

cable on the flat plug of the measuring system to the

earth connection on the SPC11.

Specially for DNCI-...

SIn order to earth the earth connection of the SPC11

and the earth connection of the drive, connect them

with the same earth potential.

Fixed stops

SUse fixed stops to limit the working stroke. With drives

of type DGP(I)(L)-..., the working stroke should not

project into the range of the end position cushioning.

Mass load

SFasten the permitted mass load to the slide without

play.

Festo SPC11 2018-12b English8

3.1 Overview of fitting and pneumatic installation

(example DGPL-... and MLO-POT-...-TLF)

1Measuring system

2Fixed stops

3Measuring system

connection

4Proportional

directional control

valve

5Service unit

(without lubricator,

with 5 μm filter)

12 3

P.01P.02

ÓÓ

Special instructions on the components used can be found

in the manuals for the SPC11.

Connections to the proportional directional control valve

When compressed air is applied to work connection 4,

movement is made in the direction of the zero point of the

measuring system. When compressed air is applied to

work connection 2, movement is made in the opposite

direction. With linear drives: the zero point of the measur

ing system lies on the side of the measuring system con

nection.

Festo SPC11 2018-12b English 9

4 Fitting the electric components

Example of fitting electric drive type DGP(L)-... and

measuring system type MLO-POT-...-TLF. Use only the

original cables specified.

24 V

0 V

O1: P.01

O2: P.02

O3: P.03

O4: P.04 *)

O5: Error *)

I1: P.01

I2: P.02

I3: P.03

I4: P.04 *)

I5: +/}

I6: Enter/Teach/Esc

I7: {/–

I8: Remote

white-yellow

brown-green

white-green

red-blue

grey-pink

violet

black

red

blue

pink

grey

yellow

green

brown

white

12 3 4

*) The function of this input/output can be configured

(see system manual P.BE-SPC11-SYS-...)

1Pin assignment for Control

connection with core colours

for cable KMPV-SUB-D-15-...

O..: output, I..: Input

2Button for moving to the

positions

3With linear drives, end

position 1 lies on the side

with the electrical

connections to the

measuring system.

4Earth/ground

Festo SPC11 2018-12b English10

Connect an earth cable with sufficient cross-sectional area

to the drive if the drive is not fitted on an earthed machine

stand. Special earthing measures for components other

than those shown here can be found in the System manual

for the SPC11.

Pin assignment on the Control connection

The function of the input I4 and outputs O4 and O5 can be

configured (see system manual for SPC11). The following

tables describe the factory settings.

Output Pin Description

O1: P.01 13 Supplies a 1-signal when the

drive is in the appropriate

position. Supplies a 1-signal for

50 ms when the drive moves past

the appropriate position.

O2: P.02 12

O3: P.03 11

O4: P.04 1) 10

O5: Error 2) 9Supplies a 1-signal if there is an

error.

O..: Output

1) Can be configured; P.04 (factory setting) or Stop

2) Can be configured; Error (factory setting) or Ready

Other manuals for SPC11 Series

Table of contents

Other Festo Controllers manuals

Festo

Festo CMMS-ST-C8-7-G2 Guide

Festo

Festo CMXH User manual

Festo

Festo MPAL-VI User manual

Festo

Festo DFPD-HD-...-HW series User manual

Festo

Festo CPX-CEC-C1-V3 User manual

Festo

Festo CMMS-ST-*-G2 Series Instruction Manual

Festo

Festo FEC-FC640 User manual

Festo

Festo SEC-ST-48-6-P01 Operating and installation instructions

Festo

Festo CMMP-AS-C5-3A-M0 Guide

Festo

Festo EduTrainer 574175 Parts list manual

Festo

Festo SPC200 Series User manual

Festo

Festo s CMMD-AS-C8-3A Guide

Festo

Festo VPPE F1A Series User manual

Festo

Festo SPC200 Series User manual

Festo

Festo SFC-DC series Reference guide

Festo

Festo VEAB User manual

Festo

Festo SFC-DC-VC-3-E-H0-CO Reference guide

Festo

Festo MPPES 010 Series User manual

Festo

Festo CMXR-C1 Installation manual

Festo

Festo SFC-LAC-IO Series Reference guide

Festo

Festo DAPS-2880-8000 R F Series Operating instructions

Festo

Festo VPPI S1BT Series User manual

Festo

Festo CMMP-AS-***-M3 Series User manual

Festo

Festo DNCKE User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual