Endress+Hauser Deltapilot M FMB50 Technical specifications
Products Solutions Services
Brief Operating Instructions
Deltapilot M FMB50
Hydrostatic level measurement
IO-Link
Pressure sensor
These Brief Operating Instructions are not a substitute for the
Operating Instructions pertaining to the device.
Detailed information about the device can be found in the
Operating Instructions and the additional documentation.
Available for all device versions via
• Internet: www.endress.com/deviceviewer
• Smartphone/tablet: Endress+Hauser Operations app
KA01523P/00/EN/02.22-00
71581315
2022-07-27
Associated documentation Deltapilot M FMB50 IO-Link
2 Endress+Hauser
1 Associated documentation
Order code:
Ext. ord. cd.:
Ser. no.:
www.endress.com/deviceviewer Endress+Hauser
Operations App
XXXXXXXXXXXX
XXXXX-XXXXXX
XXX.XXXX.XX
Serial number
1.
3.
2.
A0023555
2 About this document
2.1 Document function
The Brief Operating Instructions contain all the essential information from incoming
acceptance to initial commissioning.
Deltapilot M FMB50 IO-Link About this document
Endress+Hauser 3
2.2 Symbols used
2.2.1 Safety symbols
Symbol Meaning
DANGER
DANGER!
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
seriousor fatal injury.
WARNING
WARNING!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
seriousor fatal injury.
CAUTION
CAUTION!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minoror medium injury.
NOTICE
NOTICE!
This symbol contains information on procedures and other facts which do not result in
personalinjury.
2.2.2 Electrical symbols
Symbol Meaning Symbol Meaning
Protective ground connection
A terminal which must be connected to
ground prior to establishing any other
connections.
Ground connection
A grounded terminal which, as far as
the operator is concerned, is grounded
via a grounding system.
2.2.3 Tool symbols
Symbol Meaning
A0011221
Allen key
A0011222
Open-ended wrench
2.2.4 Symbols for certain types of information
Symbol Meaning
Permitted
Procedures, processes or actions that are permitted.
Forbidden
Procedures, processes or actions that are forbidden.
Basic safety instructions Deltapilot M FMB50 IO-Link
4 Endress+Hauser
Symbol Meaning
Tip
Indicates additional information.
Visual inspection
2.2.5 Symbols in graphics
Symbol Meaning
1, 2, 3 ... Item numbers
,…
,
1. 2. 3.
Series of steps
A, B, C, ... Views
A-A, B-B, C-C, ... Sections
2.2.6 Symbols at the device
Symbol Meaning
A0019159
Safety instructions
Observe the safety instructions contained in the associated Operating Instructions.
t 85°C>
A0029423
Connecting cable immunity to temperature change
Indicates that the connecting cables have to withstand a temperature of 85°C at least.
2.3 Registered trademarks
• KALREZ®
Registered label of E.I. Du Pont de Nemours & Co., Wilmington, USA
• TRI-CLAMP®
Registered label of Ladish & Co., Inc., Kenosha, USA
•
Registered trademark of the IO-Link Community.
• GORE-TEX® trademark of W.L. Gore & Associates, Inc., USA
3 Basic safety instructions
3.1 Requirements for personnel
Personnel must meet the following requirements for their tasks:
‣Trained, qualified specialists must have a relevant qualification for this specific function
and task
Deltapilot M FMB50 IO-Link Basic safety instructions
Endress+Hauser 5
‣Are authorized by the plant owner/operator
‣Are familiar with federal/national regulations
‣Before starting work, read and understand the instructions in the manual and
supplementary documentation as well as the certificates (depending on the application)
‣Follow instructions and comply with basic conditions
3.2 Designated use
The Deltapilot M is a hydrostatic pressure sensor for measuring level and pressure.
3.2.1 Incorrect use
The manufacturer is not liable for damage caused by improper or non-designated use.
Verification for borderline cases:
‣For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance in
verifying the corrosion resistance of fluid-wetted materials, but does not accept any
warranty or liability.
3.3 Workplace safety
For work on and with the device:
‣Wear the required personal protective equipment according to federal/national
regulations.
‣Switch off the supply voltage before connecting the device.
3.4 Operational safety
Risk of injury!
‣Operate the device in proper technical condition and fail-safe condition only.
‣The operator is responsible for interference-free operation of the device.
Conversions to the device
Unauthorized modifications to the device are not permitted and can lead to unforeseeable
dangers:
‣If, despite this, modifications are required, consult with Endress+Hauser.
Repair
To ensure continued operational safety and reliability:
‣Carry out repairs on the device only if they are expressly permitted.
‣Observe federal/national regulations pertaining to repair of an electrical device.
‣Use original spare parts and accessories from Endress+Hauser only.
Hazardous area
To eliminate a danger for persons or for the facility when the device is used in the hazardous
area (e.g. explosion protection, pressure vessel safety):
‣Based on the nameplate, check whether the ordered device is permitted for the intended
use in the hazardous area.
‣Observe the specifications in the separate supplementary documentation that is an integral
part of these Instructions.
Incoming acceptance and product identification Deltapilot M FMB50 IO-Link
6 Endress+Hauser
3.5 Product safety
This measuring device is designed in accordance with good engineering practice to meet state-
of-the- art safety requirements, has been tested, and left the factory in a condition in which
they are safe to operate.
It fulfills general safety requirements and legal requirements. It also conforms to the EC
directives listed in the device-specific EC declaration of conformity. Endress+Hauser confirms
this fact by applying the CE mark.
4 Incoming acceptance and product identification
4.1 Incoming acceptance
DELIVERY NOTE
1 = 2
A0016870
• Is the order code on the delivery note (1) identical to the order code on the product sticker
(2)?
• Are the goods undamaged?
• Do the data on the nameplate correspond to the order specifications and the delivery note?
• Is the documentation available?
• If required (see nameplate): Are the safety instructions (XA) present?
If one of these conditions is not fulfilled, please contact your Endress+Hauser sales office.
4.2 Storage and transport
4.2.1 Storage conditions
Use original packaging.
Store the measuring device in clean and dry conditions and protect from damage caused by
shocks (EN 837-2).
Storage temperature range
See the "Technical Information" document: www.endress.com → Download
Deltapilot M FMB50 IO-Link Installation
Endress+Hauser 7
4.2.2 Transporting the product to the measuring point
LWARNING
Incorrect transport!
Housing and membrane may become damaged, and there is a risk of injury!
‣Transport the measuring device to the measuring point in its original packaging or by the
process connection.
‣Follow the safety instructions and transport conditions for devices weighing more than 18
kg (39.6 lbs).
5 Installation
5.1 Mounting requirements
5.1.1 General installation instructions
• Devices with a G 1 1/2 thread:
When screwing the device into the tank, the flat seal has to be positioned on the sealing
surface of the process connection. To avoid additional strain on the process membrane, the
thread should never be sealed with hemp or similar materials.
• Devices with NPT threads:
• Wrap Teflon tape around the thread to seal it.
• Tighten the device at the hexagonal bolt only. Do not turn at the housing.
• Do not overtighten the thread when screwing. Max. tightening torque:
20 to 30 Nm (14.75 to 22.13 lbf ft)
• For the following process connections, a tightening torque of max. 40 Nm (29.50 lbf ft) is
specified:
• Thread ISO228 G1/2 (Order option "GRC" or "GRJ" or "G0J")
• Thread DIN13 M20 x 1.5 (Order option "G7J" or "G8J")
5.1.2 Mounting measuring cell modules with PVDF thread
LWARNING
Risk of damage to process connection!
Risk of injury!
‣Measuring cell modules with PVDF thread must be installed with the mounting bracket
provided!
LWARNING
Material fatigue from pressure and temperature!
Risk of injury if parts burst! The thread can become loose if exposed to high pressure and
temperature loads.
‣The integrity of the thread must be checked regularly. Also, the thread may need to be re-
tightened with the maximum tightening torque of 7 Nm (5.16 lbf ft). Teflon tape is
recommended for sealing the ½" NPT thread.
Installation Deltapilot M FMB50 IO-Link
8 Endress+Hauser
5.2 Mounting the device
5.2.1 General installation instructions
NOTICE
Damage to the device!
If a heated device is cooled during a cleaning process (e.g. by cold water), a vacuum develops
for a short time and, as a result, moisture can enter the sensor via the pressure compensation
(1).
‣Mount the device as follows.
1
1
1
1
A0028471
• Keep the pressure compensation and GORE-TEX® filter (1) free from contamination.
• Do not clean or touch process membranes with hard or pointed objects.
• The process membrane in the rod and cable version is protected against mechanical damage
by a plastic cap.
• The device must be installed as follows in order to comply with the cleanability
requirements of the ASME-BPE (Part SD Cleanability):
Deltapilot M FMB50 IO-Link Installation
Endress+Hauser 9
A0028472
5.2.2 FMB50
Level measurement
• Always install the device below the lowest measuring point.
• Do not install the device at the following positions:
• in the filling curtain
• in the tank outlet
• in the suction area of a pump
• at a point in the tank which could be affected by pressure pulses from the agitator.
• The calibration and functional test can be carried out more easily if you mount the device
downstream from a shutoff device.
• The Deltapilot M must also be insulated in the case of media that can harden when cold.
Pressure measurement in gases
Mount the Deltapilot M with the shutoff device above the tapping point so that any
condensate can flow into the process.
Pressure measurement in vapors
• Mount the Deltapilot M with the siphon above the tapping point.
• Fill the siphon with liquid before commissioning. The siphon reduces the temperature to
almost ambient temperature.
Pressure measurement in liquids
Mount the Deltapilot M with the shutoff device below or at the same level as the tapping
point.
Installation Deltapilot M FMB50 IO-Link
10 Endress+Hauser
5.2.3 Supplementary installation instructions
Seal the probe housing
• No moisture may enter the housing when installing or operating the device, or when
establishing the electrical connection.
• Always firmly tighten the housing cover and the cable entries.
5.2.4 Seal for flange mounting
NOTICE
Incorrect measurement results.
The seal is not allowed to press against the process membrane as this could affect the
measurement result.
‣Ensure that the seal is not touching the process membrane.
5.2.5 Closing the housing covers
NOTICE
Devices with EPDM cover seal - leaking transmitter!
Mineral-, animal- or plant-based lubricants cause the EPDM cover seal to swell and the
transmitter to leak as a result.
‣It is not necessary to grease the thread due to the coating applied to the thread at the
factory.
NOTICE
The housing cover can no longer be closed.
Damaged thread!
‣When closing the housing covers make sure that the threads on the covers and the housing
are free from dirt, such as sand. If you encounter resistance when closing the covers, then
check the threads again for dirt or fouling.
Other manuals for Deltapilot M FMB50
4
Table of contents
Other Endress+Hauser Measuring Instrument manuals
Endress+Hauser
Endress+Hauser EngyCal RH33 Technical specifications
Endress+Hauser
Endress+Hauser Micropilot NMR81 User manual
Endress+Hauser
Endress+Hauser dosimass User manual
Endress+Hauser
Endress+Hauser Prosonic M FMU40 User manual
Endress+Hauser
Endress+Hauser Soliwave FDR56 User manual
Endress+Hauser
Endress+Hauser Levelflex M FMP40 User manual
Endress+Hauser
Endress+Hauser Memosens Wave CAS80E User manual
Endress+Hauser
Endress+Hauser Deltabar FMD71 User manual
Endress+Hauser
Endress+Hauser Proline Promag W 400 User manual
Endress+Hauser
Endress+Hauser Proline Promag 10 User manual
Endress+Hauser
Endress+Hauser Levelflex FMP50 Technical specifications
Endress+Hauser
Endress+Hauser Proline Promag H 500 User manual
Endress+Hauser
Endress+Hauser Liquiline System CA80CR User manual
Endress+Hauser
Endress+Hauser Analytik Jena Multi X 2500 User manual
Endress+Hauser
Endress+Hauser Prosonic M FMU40 Manual
Endress+Hauser
Endress+Hauser SpectraSensors SS2100i-1 Installation guide
Endress+Hauser
Endress+Hauser Hart Cerabar PMP71B User manual
Endress+Hauser
Endress+Hauser Levelflex FMP50 Installation instructions
Endress+Hauser
Endress+Hauser Micropilot FMR10 User manual
Endress+Hauser
Endress+Hauser Levelflex FMP51 User manual
