Emerson Fisher L2e User manual

www.Fisher.com

Fisher™L2e Electric Level Controller

Contents

Introduction 1.................................

Scope of Manual 1.............................

Description 2.................................

Specifications 2...............................

Educational Services 2.........................

Installation 4..................................

Attaching a Vertical Displacer 5..................

Attaching a Horizontal Displacer 5...............

Attaching the Sensor to the Vessel 5.............

Electrical Connections 6........................

L2e Initial Setup (Dry Displacer) 10...............

L2e Zero and Span Adjustment (Wet Displacer) 10..

Principle of Operation 11........................

Maintenance 12................................

Removing the Controller From the Sensor 12......

Installing Sensor Repair Kit (RL2SENSX012) 12.....

Replacing the Complete Controller

Assembly (RL2E0X00C12) 13.................

Related Documents 14..........................

Parts Ordering 14...............................

Figure 1. Fisher L2e Electric Level Controller

X0660

Introduction

Scope of Manual

This instruction manual includes installation, adjustment, maintenance, and parts ordering information for the Fisher

L2e electric liquid level controller.

Do not install, operate or maintain an L2e electric liquid level controller without being fully trained and qualified in

valve, actuator, and accessory installation, operation, and maintenance. To avoid personal injury or property damage,

it is important to carefully read, understand and follow all the contents of this manual, including all safety cautions

and warnings. If you have any questions about these instructions, contact your Emerson sales office or Local Business

Partner before proceeding.

Instruction Manual

D103531X012

L2e Controller

May 2017

Instruction Manual

D103531X012

L2e Controller

May 2017

Description

The L2e electric liquid level differential gap on-off controller uses a displacement type sensor to detect liquid level or

the interface of two liquids of different specific gravities.

The L2e controls the lower trip point (zero) that closes the dump valve, allowing the vessel to fill to the upper trip

point. Once the upper trip point is reached, the dump valve opens to drain the fluid down to the zero or lower trip

point. The difference between the upper trip point and the zero or lower trip point is called differential gap or DG. The

L2e operates as a two position (on-off) controller.

These controllers use a single pole double throw (SPDT) dry contact electric switch to provide differential gap (DG)

control or liquid monitoring. The controller can be used to provide an electric control signal to an electrically actuated

control valve.

Unless otherwise noted, all NACE references are to NACE MR01752002.

Specifications

Specifications for the controller and sensor are listed in table 1.

Educational Services

For information on available courses for L2e electric liquid level controllers, as well as a variety of other products,

contact:

Emerson Automation Solutions

Educational Services - Registration

Phone: 1-641-754-3771 or 1-800-338-8158

E-mail: [email protected]

emerson.com/fishervalvetraining

Instruction Manual

D103531X012

L2e Controller

May 2017

Table 1. Specifications

Available Configurations

Controller: Differential gap (DG) electric control

action with intuitive Zero and Span Adjustments in

SPDT dry contact configuration (refer to page 2 for

differential gap description)

Sensor: Displacertype liquid level sensor for

mounting to side of vessel

Input Signal

Type: Liquid level or liquidtoliquid interface

Level Change Required for Full Change in State of

Output: 5.0 to 305 mm (0.2 to 12 inches)

Vessel level DG is dependant on factors such as valve

sizing, actuator speed, rate, liquid out flow, and

vessel size. Contact your Emerson sales office or Local

Business Partner for Fisher Electric Level Loop

performance optimization.

Specific Gravity Limits

Minimum SG: 0.15

Maximum SG

PVC Displacer: 1.3

SST Displacer: 1.1

Electrical Rating (Output)

Jeasy-Drive™ actuator application: 7 mA@5 VDC

JOther applications: 1 amp resistive, 0.5 amp

inductive/28 VDC

Note: Use with easy-Drive after first being used in

other high power application is not recommended.

Power Consumption

Switch consumes no power to operate, so it has no

current leakage or voltage drop

Sensor to Vessel Connection

J2 NPT threaded or JNPS 2 CL150 through 1500

slipon flange connection(1)

Controller Connection

Electrical 1/2-14 NPT external conduit connection

with 18 inches of 18 AWG lead wires, located at the

bottom of the case

Displacer Sizes

J48 X 305 mm, 541 cm3(17/8 X 12 inches, 33 in3)

J76 X 152 mm, 688 cm3(3 X 6 inches, 42 in3)

Maximum Displacer Insertion Length(2), Horizontal

or Vertical

1-7/8 x 12 Displacer with one 6-inch extension

(optional use)

3 x 6 Displacer with one 3-inch extension

(optional use)

Displacer Material and Maximum Sensor Working

Pressure(3)

PVC Displacer: Consistent with CL1500 pressure

temperature ratings per ASME B16.34 up to

maximum pressure of 258.5 bar (3750 psig).

For PED (97/23/EC) maximum pressure limited to

200 bar (2900 psig).

S31603 SST Displacer: CL600 pressure temperature

ratings per ASME B16.34 up to maximum pressure of

99.3 bar (1440 psig)

Note: For slipon flange connection, maximum sensor

working pressure must be consistent with the flange

ratings

Operative Ambient Temperature Limits(3)

Controller: 40 to 75°C (40 to 167°F)

Operative Process Temperature Limits(3)

Sensor:

JPVC Displacer: -18 to 71°C (0 to 160°F)

JS31603 SST Displacer: 40 to 204°C (40 to 400°F)

Construction Materials

Controller

Case and Cover: Marine grade aluminum

Switch: Stainless steel

Span Levers: Stainless steel

Springs: Stainless steel

Sensor

Sensor Body: LCC

ORings: Fluorocarbon

Pivot Assembly: Stainless steel

Displacer: JPolyvinylchloride (PVC) or JS31603 SST

Sensor Spring: Stainless steel

-continued-

Instruction Manual

D103531X012

L2e Controller

May 2017

Table 1. Specifications (continued)

Hazardous Area Classifications Available

Switch Only

cCSAus

Explosion-proof Class I Division 1, Groups ABCD

Dust Ignition-proof Class II Division 1, Groups EFG

Dual Seal

ATEX II 2 GD

Flameproof Ex d IIC T6 (Ta=40°C to + 75°C)

Dust Ex tb IIIC T85°C Db IP6X (Ta = 40° to +75°C)

1 A Max

IECEx

Flameproof Ex d IIC T6 (Ta=40°C to + 75°C)

Dust Ex tb IIIC T85°C Db IP6X (Ta = 40° to +75°C)

1 A Max

Canadian Registration (CRN)

The L2e utilizes the same sensor unit pressure

component as the L2 pneumatic controller version.

Refer to the L2 CRN which is deemed applicable to

the L2e.

Declaration of SEP

Fisher Controls International LLC declares this

product to be in compliance with Article 4 paragraph

3 of the PED Directive 2014/68/EU. It was designed

and manufactured in accordance with Sound

Engineering Practice (SEP) and cannot bear the CE

marking related to PED compliance.

However, the product may bear the CE marking to

indicate compliance with other applicable European

Community Directives.

NOTE: Specialized instrument terms are defined in ANSI/ISA Standard 51.1  Process Instrument Terminology.

1. Converting from a threaded NPT connection to a flange connection is to be done by the end-user. Refer to Converting a Threaded NPT Connection to a Flange Connection instruction Manual

Supplement (D103277X012), available at Fisher.com or from your Emerson sales office or Local Business Partner.

2. Maximum span setting with 1 7/8 x 12 inch horizontal displacer plus 6 inch extension is not recommended due to potentially insufficient zero adjustment.

3. The pressure and temperature limits in this document and any applicable code limitations should not be exceeded.

Installation

WARNING

Always wear protective clothing, gloves, and eyewear when performing any installation operations to avoid personal

injury.

To avoid personal injury or property damage caused by the sudden release of process fluid, be certain the service

conditions do not exceed the sensor pressure limits. Use pressurelimiting or pressurerelieving devices to prevent service

conditions from exceeding these limits.

Check with your process or safety engineer for any additional measures that must be taken to protect against process

media.

If installing this into an existing application, also refer to the WARNING at the beginning of the Maintenance section of this

instruction manual.

CAUTION

If the L2e electric level controller is installed on a vessel that is to be shipped to a different location (e.g. skid mounted

units), remove the displacer and displacer rod extensions before shipment. Failure to do so could result in damage to the

instrument and or the displacer rod due to vibration and impact loading during shipment. After the vessel is installed at its

final location, reassemble the displacer and displacer rod extension.

Note

Use with easyDrive electric actuator after first being used in other high power application is not recommended.

Instruction Manual

D103531X012

L2e Controller

May 2017

1. Be sure there are no obstructions inside the vessel that will interfere with displacer installation or operation.

2. Provide the appropriate connection in the vessel wall to match the sensor connection. Locate the vessel wall

connection such that the displacer will be at the desired control level.

Attaching a Vertical Displacer

Refer to figure 9 for part locations.

1. Thread jam nut (key 63) all the way onto the threaded portion of the universal joint assembly (key 69).

2. Thread the displacer (key 81) all the way onto the threaded portion of the universal joint assembly.

3. Tighten the jam nut against the displacer.

Attaching a Horizontal Displacer

Refer to figure 9 for part locations.

1. Thread the displacer (key 81) all the way onto the displacer rod (key 64) or extension (key 82) and tighten.

Attaching the Sensor to the Vessel

Insert the displacer end of the L2e sensor into the vessel connection and tighten enough to seal the threads. If

necessary, loosen or tighten slightly to obtain the horizontal orientation shown in figure 2. Make sure that the

controller case is level.

CAUTION

The displacer rod (key 64) is not a handle. Grasp sensor body or controller housing to lift and carry to avoid internal

component damage.

Figure 2. Sensor Orientation

CORRECT CONTROLLER MOUNTING

HOLE ORIENTATION WHEN MOUNTED ON VESSEL

A6639

Instruction Manual

D103531X012

L2e Controller

May 2017

Electrical Connections

WARNING

For explosionproof applications, disconnect power before installing, servicing or removing electrical components.

Personal injury or property damage from fire or explosion may result if power is not disconnected.

Select junction boxes, wiring and/or cable glands that are rated for the environment of use (such as hazardous location,

ingress protection, and temperature). Failure to use properly rated electrical hardware wiring and/or cable glands can

result in personal injury or property damage from fire or explosion. Wiring connections must be in accordance with local,

regional, and national codes for any given hazardous area approval. Failure to follow the local, regional, and national codes

could result in personal injury or property damage from fire or explosion.

An electrical 1/2-14 NPT conduit connection with 18 inches of 18 AWG lead wires is located at the bottom of the case.

The conduit connection is integral to the body of the switch.

The action of the controller is such that rising level will cause the Normally Closed (N/C) contacts to close and the

Normally Open (N/O) contacts to open. Falling level causes the opposite action.

Connect L2e electrical wires as shown in table 2. To reverse the action refer to table 2 and reverse wiring for normally

open and normally closed.

Table 2. L2e Electrical Wire Configuration

Wire Color SPDT Action

Red Normally Closed

Brown Common

Blue Normally Open

Green Ground

Instruction Manual

D103531X012

L2e Controller

May 2017

Wiring Configurations

There are two recommended wiring configurations depending on the preferred site solution and approach to electric

level control; a direct connection to the easy-Drive actuator, shown in figure 3 or a direct connection to the easy-Drive

actuator and a remote monitor (figure 4 and 5). In these examples, the L2e is wired using a common and separate N/O

or N/C contact. When implemented as suggested, these wiring configurations provide definitive level switch points

and help reduce issues associated with single pole single throw contact switches, such as “bouncing” due to vibration

or sloshing liquids in a vessel.

Note

Use with easyDrive electric actuator after first being used in other high power application is not recommended.

OPEN

Figure 3. Local Level Control with Direct Connection to easy-Drive Actuator without Remote Monitor

BROWN

RED

BLUE

12/24 VDC

POWER SUPPLY

easy-Drive ACTUATOR

POWER AND CONTROL TERMINAL

X0661

GREEN (GND)

1 CONNECT GREEN WIRE TO ACTUATOR GROUND (NOT SHOWN)

2 OPEN CONTACT (2) MAY BE LABELED N.O. AND CLOSE CONTACT (3) MAY BE LABLED N.C.

W9795-4

REMOVE COVER TO

ACCESS POWER AND

CONTROL TERMINAL

easy-Drive ACTUATOR WITH

FISHER D3 CONTROL VALVE

Instruction Manual

D103531X012

L2e Controller

May 2017

BROWN

RED

BLUE

RED

BLUE

BROWN

DISCRETE INPUT CONFIGURED FOR DRY CONTACT CLOSURE EXTERNALLY POWERED

12/24 VDC

POWER SUPPLY

easy-Drive ACTUATOR

POWER AND CONTROL TERMINAL

ROC809 DI MODULE

X0661

OPEN

1 CONNECT GREEN WIRE TO ACTUATOR GROUND (NOT SHOWN)

2 OPEN CONTACT (2) MAY BE LABELED N.O. AND CLOSE CONTACT (3) MAY BE LABLED N.C.

GREEN (GND)

REMOVE COVER TO

ACCESS POWER AND

CONTROL TERMINAL

W9795-4

easy-Drive ACTUATOR WITH

FISHER D3 CONTROL VALVE

Figure 4. Local Level Loop Control with Direct Connect to easy-Drive Actuator

with ROC809 Remote Monitor

Instruction Manual

D103531X012

L2e Controller

May 2017

W9795-4

Figure 5. Local Level Loop Control with Direct Connect to easy-Drive Actuator

with FloBoss 107 Remote Monitor

BROWN

RED

BLUE

RED

BLUE

BROWN

DISCRETE INPUT CONFIGURED FOR DRY CONTACT CLOSURE EXTERNALLY POWERED

12/24 VDC

POWER SUPPLY

FloBoss 107 AI/DI MODULE OR

FloBoss 107 DIs ON CPU

MODULE'S OPTIONAL I/O ASSEMBLY

X0661

OPEN

1 CONNECT GREEN WIRE TO ACTUATOR GROUND (NOT SHOWN)

2 OPEN CONTACT (2) MAY BE LABELED N.O. AND CLOSE CONTACT (3) MAY BE LABLED N.C.

GREEN (GND)

REMOVE COVER TO

ACCESS POWER AND

CONTROL TERMINAL

easy-Drive ACTUATOR

POWER AND CONTROL TERMINAL

easy-Drive ACTUATOR WITH

FISHER D3 CONTROL VALVE

Instruction Manual

D103531X012

L2e Controller

May 2017

L2e Initial Setup (Dry Displacer)

Refer to figure 6.

1. Move Span to minimum setting.

2. Move Zero down until the valve opens, or N/C contact (red to brown leads) closes.

3. Slowly move Zero up until valve closes, or N/C contact (red to brown leads) opens.

L2e Zero and Span Adjustment (Wet Displacer)

After initial setup (dry displacer) is complete,

1. Enable process flow into the vessel.

2. Move Zero and Span Adjustment for desired liquid zero position and level DG.

3. Tighten the Zero Adjustment hex nut (key 5), shown in figure 7, to lock the Zero setting.

Note

Scan the QR code shown in figure 6 or on the inside cover of the L2e for electric level loop field support.

Figure 6. Initial Setup

GG11109

Other manuals for Fisher L2e

Table of contents

Other Emerson Controllers manuals

Emerson

Emerson Fisher S200 Series User manual

Emerson

Emerson EC2-311 User manual

Emerson

Emerson Dixell WING XW563L Wiring diagram

Emerson

Emerson Bettis PressureGuard Manual

Emerson

Emerson Fisher 67D Series User manual

Emerson

Emerson Fisher FIELDVUE DVC6200 HW2 Configuration guide

Emerson

Emerson Fisher EZL User manual

Emerson

Emerson Fisher S202 User manual

Emerson

Emerson Fisher Fieldvue DVC6030f User manual

Emerson

Emerson Dixell XR20T User manual

Emerson

Emerson Fisher Y692 User manual

Emerson

Emerson Hytork XL26 Instruction manual

Emerson

Emerson TARTARINI PS/80-1 User manual

Emerson

Emerson White-Rodgers 11B79-3 User manual

Emerson

Emerson Fisher Accu-Pressure Y693 User manual

Emerson

Emerson Vilter MicroVission User manual

Emerson

Emerson EL-O-Matic F-Series User guide

Emerson

Emerson Control Link Refrigeration System Controller User manual

Emerson

Emerson SP User manual

Emerson

Emerson Dixell iPro Master IPM500D Wiring diagram

Emerson

Emerson TARTARINI RP Series User manual

Emerson

Emerson Topworx D Series User manual

Emerson

Emerson Dixell XWi70K Wiring diagram

Emerson

Emerson FD113 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide