Emerson Micro Motion User manual

Quick Start Guide

MMI-20019807, Rev AD

January 2019

Micro Motion® EtherNet/IP Module

1 Quick installation and startup

This procedure provides a summary of installation and startup steps. For

installation details, see the EtherNet/IP Module User Manual.

1.1 Components

Ensure that you have all required components:

•Micro Motion EtherNet/IP Module

•Power connector

•Micro Motion EtherNet/IP Resource CD

—Micro Motion EtherNet/IP Module User Manual

—EDS file

—MicroMotion Ethernet Config Tool

•Configuration cable

•Modbus serial cable and connector (included)

•Ethernet cable and connector (not included)

1.2 Set up the module with MVD Direct Connect

Use this procedure only if you are installing the module with MVD Direct

Connect.

Procedure

1. Mount and wire the core processor and barrier.

Figure 1-1: Barrier

A. I.S. terminals for connection to core processor

B. Non-I.S. terminals for connection to remote host and power supply

2. Power up the core processor and barrier.

3. Set the Modbus address on the core processor to 1.

Postrequisites

Continue to Mount, wire, and set the network settings.

Quick Start Guide January 2019

2 Micro Motion EtherNet/IP Module

1.3 Set up the transmitter

Use this procedure only if you are installing the module with a transmitter.

Procedure

1. Mount the transmitter and wire it to the sensor and to power.

2. Power up the transmitter.

3. Set the Modbus address on the transmitter to 1.

4. If your transmitter does not support Modbus auto-detect, configure

the RS-485 terminals as follows:

•Modbus RTU

•38400 baud

•2 stop bits

•No parity

Postrequisites

Continue to Mount, wire, and set the network settings.

1.4 Mount, wire, and set the network settings

Use this procedure to mount, wire, and set the network settings for both the

transmitter and MVD Direct Connect configurations.

Procedure

1. Ensure that the following slot registers are available for use by the

EtherNet/IP Module:

•655–750

•751–846

If these slot registers are currently in use, you must reprogram your

Modbus interface.

2. Mount the EtherNet/IP Module on the DIN rail.

Figure 1-2: Snap on

January 2019 Quick Start Guide

Quick Start Guide 3

Figure 1-3: Snap off

3. Wire the EtherNet/IP Module to power (24 VDC).

Figure 1-4: Power connections on the EtherNet/IP module

A. 24 VDC

B. Ground

4. Install the Modbus serial cable between the EtherNet/IP Module and

the RS-485 terminals on the transmitter (or the I.S. barrier, if present).

Quick Start Guide January 2019

4 Micro Motion EtherNet/IP Module

Figure 1-5: Modbus serial connector on the EtherNet/IP module

See Modbus terminals and Pin assignments (EtherNet/IP Module).

5. Set the configuration dip switches on the EtherNet/IP module as

follows:

•Switches 1–7: Off

•Switch 8: On

The IP addess is set to 192.168.0.1.

6. If you are using a Model 1500, Model 2500, or Series 3000 transmitter,

ensure that the RS-485 terminals are in RS-485 mode.

7. Cycle power to the transmitter and wait 15 seconds before applying

power to the EtherNet/IP Module.

8. Power up the EtherNet/IP Module.

The module will attempt to make a Modbus connection to the

transmitter.

9. Is the Subnet Status LED (LED 5) green?

Option Description

Yes Continue with these steps.

No See LED indicators.

10. Set the network settings for the EtherNet/IP Module.

a) Change the Ethernet address setting for your PC so that it is on

the same subnet as the device. When prompted, enter the

following:

•IP address: 192.168.0.x, where x is something other

than 1

January 2019 Quick Start Guide

Quick Start Guide 5

•Subnet mask: 255.255.255.0

b) Disable the popup blocker on your web browser.

c) Use a crossover cable (or a standard cable with a switch) and

your web browser to connect to the device, using the IP

address assigned in Step 6: 192.168.0.1.

d) At the login screen, log in as user admin. The default password

is admin. Ignore the auto-configuration popup window.

e) On the Network Settings page, change the settings as

required, and close the web browser.

f) At the EtherNet/IP Module, set all dip switches to Off.

g) Cycle power to the EtherNet/IP Module.

11. Connect the EtherNet/IP Module to the Ethernet network.

See Ethernet connector.

12. Wait for the auto-configuration process to complete.

Important

For initial startup, you must use the auto-configuration process to

ensure that device memory is completely set up.

13. Add the EtherNet/IP Module to the Ethernet network control system.

The EDS file is available on the Resource CD, the EtherNet/IP Module

(download from Administration page), and the Emerson web site.

Postrequisites

For more information on transmitter installation and wiring, see your

transmitter installation manual. For information on configuring the RS-485

terminals and making an RS-485 connection, see your transmitter

configuration manual.

1.4.1 Modbus terminals

Transmitter RS-485/A RS-485/B

Model 1500 33 34

Model 1700 with analog outputs 5 6

Model 2500 33 34

Model 2700 with analog outputs 5 6

Model 3500 with screw-type or solder-tail

terminals

32a 32b

Model 3500 with I/O cables 25 24

Model 3700 12 11

Quick Start Guide January 2019

6 Micro Motion EtherNet/IP Module

1.4.2 LED indicators

LED

number

Name Status Description

AModule

Status

(EtherNet)

Off No power applied to the module.

Solid green The module is operating correctly.

Flashing green Standby. The module has not been

initialized.

Flashing red Minor fault. The module may or may

not be able to recover.

Solid red Major fault. No recovery is possible. The

module must be retuned to Micro

Motion for repair. See the manual for

the return policy.

Flashing green/red Self-test.

BNetwork

Status

(EtherNet)

Off The module has not power or no IP

address has been assigned.

Solid green The module has at least one

established EtherNet/IP connection.

Flashing green There are no EtherNet/IP connections

established to the module.

Flashing red One or more of the connections to this

module has timed out.

Solid red The module has detected that its IP

address is already in use.

Flashing green/red Self-test.

C Link Off The module does not sense a link.

January 2019 Quick Start Guide

Quick Start Guide 7

LED

number

Name Status Description

Green The module is connected to an

Ethernet network.

D Activity Flashing green Packet is received or transmitted.

ESubnet

Status

(Modbus

Serial)

Off Power off.

Flashing green Running correctly, but one or more

transaction errors has occurred.

Green Running.

Red Transaction error/timeout or network

stopped. Check the Modbus serial

network wiring and configuration,

especially the baud.

Flashing red Missed transactions.

FDevice

Status

(Modbus

Serial)

Off Power off.

Flashing red/green Configuration missing or invalid.

Red Contact customer service.

Flashing red Contact customer service.

Green Initializing.

Flashing green Configuration OK.

Quick Start Guide January 2019

8 Micro Motion EtherNet/IP Module

January 2019 Quick Start Guide

Quick Start Guide 9

Quick Start Guide January 2019

10 Micro Motion EtherNet/IP Module

Other manuals for Micro Motion

Table of contents

Other Emerson Control Unit manuals

Emerson

Emerson Fisher Slurry Vee-Ball V300S User manual

Emerson

Emerson KTM Hindle 300 Series User manual

Emerson

Emerson Bettis XTE3000 User manual

Emerson

Emerson Fisher GX User manual

Emerson

Emerson Betis E Series Operation manual

Emerson

Emerson Tartarini BM5 Series User manual

Emerson

Emerson Keystone Figure 56 User manual

Emerson

Emerson EIM PCU REV A4 Manual

Emerson

Emerson SEMPELL Quick guide

Emerson

Emerson Bettis 2000 Series User manual

Emerson

Emerson PENBERTHY N7 Series Manual

Emerson

Emerson Fisher 6010 User manual

Emerson

Emerson Fisher 161 Series User manual

Emerson

Emerson ALCO CONTROLS FSE-0 User manual

Emerson

Emerson Anderson Greenwood 95 Series User manual

Emerson

Emerson Anderson Greenwood 93 Series User manual

Emerson

Emerson VAREC 3600B Series Operation and maintenance manual

Emerson

Emerson E5 User manual

Emerson

Emerson Fisher Baumann Little Scotty 24000C User manual

Emerson

Emerson KEYSTONE V30 Series Owner's manual

Emerson

Emerson Fisher YD User manual

Emerson

Emerson Yarway User manual

Emerson

Emerson KEYSTONE FIGURE 955 User manual

Emerson

Emerson Fisher 6060 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual