Eaton S611 Manual

Installation Leaet IL03901007E Effective June 2011

S611 User Interface Remote Mounting

Installation Leaﬂet

Disconnect power in accordance with federal, state, and local codes and remove the S611 from the enclo-

sure or mounting panel.

NOTE: Servicing the S611 while installed in an enclosure or mounted vertically on a panel is not recom-

mended.

Place the unit on a clean work surface.

Cover Removal

1. Disconnect all control wiring and tie wraps securing any wiring to the cover assembly.

2. Remove cover screws with nuts. 6 each on Frames A – D, 4 each on Frames E - F.

NOTE: Cover screw nuts are prevented from rotating but are not retained in place by the pole

supports. Do not allow hardware to fall into the soft starter.

3. Lift top of cover approximately 6” to gain access to the BYPASS VOLTAGE contactor

connector mounted on the Printed Circuit Board (PCB). See Figure 1.

4. Press locking tab on BYPASS VOLTAGE contactor connector and disconnect from the PCB.

5. Carefully rotate cover to rest onto work surface as shown. See Figure 2.

Figure 1 - Contactor Connector Figure 2 - Cover Position

Mounting The Remote Display

If necessary, remove the User Interface from the cover using a 30mm pilot device tool (E22CW recom-

mended).

1. Drill or punch two 30mm pilot holes on 1.75-inch centers a minimum of 1.60 inches (40.6 mm)

from every door gasket (see Figure 3).

2. Insert remote display through the door and add two gaskets provided behind the door

(see Figure 4).

Installation Leaet IL03901007E

Effective June 2011

S611 Soft Starters

Eaton Corporation

Electrical Sector

1111 Superior Ave.

Cleveland, OH 44114

United States

877-ETN-CARE (877-386-2273)

Eaton.com

Publication No. IL03901007E

June 2011 Rev.001

PowerChain Management is a registered

trademark of Eaton Corporation.

All other trademarks are property of their

respective owners.

Figure 3 - Pilot Device Holes - Inch[mm]

Minimum to all

gaskets ordoor

mounteddevices

1.60

[40.6]

1.75

[44.5]

Gaskets

E22CW

Tighten

Figure 4 - Door Cut Away For Clarity

3. Orient strain relief bracket with respect to your chosen cable routing.

4. Add two jam nuts provided and tighten 30mm pilot device tool until the strain relief bracket is

flush with the enclosure door, tighten an additional ½ of a turn.

Connecting the Remote Display

1. Route cable from User Interface to PCB (see Figures 5 & 6).

2. Secure cable to the strain relief bracket using any suitable tie wrap.

3. Reinstall cover assembly.

Figure 5 - Interconnecting Cable - PCB Figure 6 - Interconnecting Cable - User Interface

Cover Reinstallation

1. As the cover is placed onto the supports, carefully guide wiring into place.

2. Ensure that the BYPASS VOLTAGE contactor connector is properly connected prior to installing

the cover screws.

3. Install and torque all cover assembly screws to 22 – 27 lb-in.

4. Reinstall control wiring.

Other manuals for S611

Table of contents

Other Eaton Controllers manuals

Eaton

Eaton PKE-SWD-32 User manual

Eaton

Eaton Cutler-Hammer ELC Series Installation guide

Eaton

Eaton COOPER POWER SERIES Manual

Eaton

Eaton ELC-PB Owner's manual

Eaton

Eaton A201 Manual

Eaton

Eaton RMQ-Titan M22 Series Manual

Eaton

Eaton LMR PLUS User manual

Eaton

Eaton DS7 Series Manual

Eaton

Eaton Cutler-Hammer Pow-R-Command JCI-100 Manual

Eaton

Eaton Vikers V200 Series User manual

Eaton

Eaton CGLine+ CGVision Series Operating and maintenance instructions

Eaton

Eaton SC100 User manual

Eaton

Eaton BLR-ACX User manual

Eaton

Eaton ELCB Series User manual

Eaton

Eaton xComfort CDAE-01/01 User manual

Eaton

Eaton ESWA4500C User manual

Eaton

Eaton CEAG CG-Controller User manual

Eaton

Eaton xComfort CDAE-01/01 User manual

Eaton

Eaton FD120 User manual

Eaton

Eaton DE1-12 Series Manual

Eaton

Eaton xComfort CRCA-00/10 Instruction manual

Eaton

Eaton Cutler-Hammer LMR User manual

Eaton

Eaton S811+N37 series User manual

Eaton

Eaton xComfort CAAE-01/03 Manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual