Eaton ESWA4500C User manual

ESWA4500C Multi-Source Volume Control Module

Installation Manual

Control functions [1] [2] [3]

System ON - The EATON A-BUS system will activate if any function button is pressed.

Input Selection [1] - The system will restart on the last source selected. One of the four input

LEDs [5] will indicate which input has been selected. The input can be changed by pressing

left or right buttons [1].

Volume Level [2] - If the system has been switched off the Volume Control will restart at low

volume level. If the system has remained active the Volume Control will return to the

previously selected volume level. The level may be adjusted by pressing the Up/Down

buttons [2]. While the level is being adjusted, the input LEDs [5] will ripple left or right.

Remote Control [4] - The Volume Control may be operated by remote control. The IR remote

must have clear line-of-site to the IR Receiver. The Volume Control can also relay IR remote

control commands to the hub and connected source components. It will repeat standard 38

kHz commands and 56 kHz commands which are often used in satellite receivers. You may

experience difficulty with some remote control commands on some components. The

operating range can be affected by sunlight and some lighting systems.

Off and All Off [3] - A Volume Control can be switched off individually by pressing the off

button, this will turn off the backlighting to the volume control [2] and input selection buttons

[1]. The backlighting of the off [3] and input indicator will [5] remain on. If there are other

Volume Control’s connected to the same zone their status will not be affected. If the off button

[3] is pressed for more than three seconds the whole A-BUS system will turn off. When the

system is off the infrared relay system will remain active.

Backlight adjustment [6] - The backlighting level of the function buttons [1] [2] [3] can be

adjusted to individual requirements.

This Keypad Volume Control Module has been

designed to work with intelligent EATON A-BUS

Multi-Source Hubs using standard A-BUS commands.

It will operate with other single source and multi-source

hubs, however, some functionality such as source

selection maybe not be available.

These functions can be accessed with a remote control

handset containing the correct codes.

Note: For comprehensive instructions please also refer

to the instructions supplied with your EATON A-BUS

multi-source hub.

A-BUS is a registered trademark of LeisureTech Electronics Pty Ltd.

All features and specifications are subject to change without notice.

All trademarks property of their respective owners.

Installation

It is recommended that your EATON Volume Control is installed by a qualified installer to ensure

that the installation is carried out correctly and it complies with all relevant installation regula-

tions. The Volume Control should not be installed next to or in the same box as high voltage

devices. The Volume Control is connected to the hub via a single category 5 cable, it is recom-

mended that it should not be run parallel or close to high voltage cables or data cables, etc.

The EATON Volume Control is designed to fit into a single Gang bracket. The category 5 cable

from the hub should be properly connected to either the 110 punchdown [7], using a proper

installation tool. It is recommended that the category 5 cable length be no longer than 100ft.

(30M), longer runs may induce noise and reduce sound quality. The speaker cable terminal [8]

will accept up to 14 gauge cable.

Set-up [9] - The A-BUS installation should be completed with all power modules connected but

not installed into the walls. Follow these steps to give you maximum control flexibility over the

volume of your A-BUS system. On the back of the power modules there are trim pots (Left &

Right) [9] that fine-tune the output level to compensate for the length of the cable run, the

efficiency of the speakers and the size of the room. There are also situations where you may

want to limit the output level in a particular room. With the trim pots adjusted to minimum, the

main volume control should be adjusted to maximum level, then with popular music playing the

trim pots should be brought up to a point just below the amplifier’s clipping level. (Clipping is the

point where the sound starts to distort). When the trim pots are all set to the desired level the

installation may be completed.

Mini Remote Control Handset ESWA100CR

The mini remote control handset supplied contains basic A-BUS remote control commands,

volume Up/Down [10] up to 4 individual input selections [11] Off [12] andAll Off (Global) [13]. In

good conditions this handset should have an operating range of up to 70ft. (20M), in poor

conditions such as bright sunlight it maybe less than 15ft. (5M).

42mm

BACKESWA100CR REMOTE CONTROL

SUPPLIED

PUNCHDOWN VERSION SHOWN

FRONT

70.25mm

106mm

42.75mm

71mm

L- L+

R+ R-

SPEAKER OUT

BR BRW BL BLW GR GRW OR ORW

LEVEL ADJUST

L CH R CH

ESWA100CR

Table of contents

Other Eaton Controllers manuals

Eaton

Eaton xComfort CSAU-01/03 User manual

Eaton

Eaton ATC-600 Programming manual

Eaton

Eaton SC300 User manual

Eaton

Eaton EC500 User manual

Eaton

Eaton DS7 Series Manual

Eaton

Eaton Cuttler-Hammer Pow-R-Command 100 Instruction manual

Eaton

Eaton RF System 2.42 User manual

Eaton

Eaton DS7 Series User manual

Eaton

Eaton CDAU-01/04 Manual

Eaton

Eaton ELC-PC12NNAR User manual

Eaton

Eaton Xcomfort CSAU-01/01 User manual

Eaton

Eaton EFX48 e-Fuse Series Operating instructions

Eaton

Eaton AMPGARD RVSS Operating and maintenance manual

Eaton

Eaton xComfort CSEZ-01/07 User manual

Eaton

Eaton PKZM01 Series Manual

Eaton

Eaton xComfort CAAE-01/01 User manual

Eaton

Eaton C441 Series User manual

Eaton

Eaton C22- P Series Manual

Eaton

Eaton DE1-121D4 Series Manual

Eaton

Eaton RMQ-Titan M22 Series Manual

Eaton

Eaton SC100 User manual

Eaton

Eaton CDAE-01/04 User manual

Eaton

Eaton xComfort CDAE-01/01 User manual

Eaton

Eaton MVX9000 Series User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual