DT Research DT318CR Assembly instructions
Mobile Tablet
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131
Copyright © 2019, DT Research, Inc. All Rights Reserved. BOG1015 DT318CR ENG
INTRODUCTION
Thank you for acquiring the DT318CR, part of DT Research’s line of tablets. Featuring
a slim yet robust enclosure, the DT318CR with a 8” TFT display is powered by the
Intel® Atom™ quad-core processor, oering opmal combinaons of performance
and power savings. The DT318CR is available with Microso® Windows® operang
system. The soware operang system features web browser, client/ server
compung soware, media player, accessories, and applicaons support.
PACKAGE CONTENTS
• One DT318CR with Baery Pack and Handstrap
• AC-DC Power Adapter with Power Cord
• Basic Operaon Guide
* If your DT318CR contains camera, MSR or barcode scanner, please refer to the
Tablet Modules Basic Operaon Guide for detailed operaon.
DT318CR
Button Functions
BUTTON ACTION
Power Buon
Programmable Buon
without the Scanner
module
As Scanner Trigger
when equipped with
the Scanner module
Baery Latch
Input/ Output Ports
Barcode Scanner (oponal)
Magnec Stripe Reader (oponal)
USB Port
DC Power Input
Headphone Jack
Camera (oponal)
EMC® Chip-and Signature Card
Reader (oponal)
A
B
C
23
PRECAUTIONS
• Always exercise care when operang and handling the DT318CR.
• Do NOT apply excessive pressure to the display screen.
• Avoid prolonged exposure of the display panel to any strong heat source.
Wherever possible, the DT318CR should face away from direct light to reduce
glare.
• If the AC-DC power adapter is used to recharge or power the tablet, do NOT use
any AC-DC adapter other than the one provided or acquired from the manufac-
turer or its partners.
• In the unlikely event that smoke, abnormal noise, or strange odor is present,
immediately power o the DT318CR and disconnect all power sources. Report
the problem to your device provider immediately.
• Never aempt to disassemble the DT318CR, as this will void the warranty.
BASIC FEATURES
The DT318CR wireless tablet integrates a bright and mul-touch display, one USB
port, and embedded networking elements such as wireless LAN and Bluetooth. The
DT318CR is complemented by a suite of accessories, including baery expansion, and
charging cradles, for a comprehensive user experience.
A DT318CR typically integrates an 802.11ac wireless LAN (WLAN) adapter that may
connect to other wireless devices or access points. If your DT318CR does not come
with such a network adapter, please consult your device provider to establish the
desired network connecvity.
1
2
3
D
E
F
G
Power/Battery LED Status:
• Blue indicates the baery is 25% to 100% charged
• Blinking blue indicates the baery is charging
• Orange indicates that the baery is between 11% to 25%
• Blinking Orange indicates that the baery is below 10%
Baery/Power LED
1
3
2
C
G
A
F
D
E
B
Start Up
If the power up (from Standby mode or otherwise) is successful, the appropriate
interface will be displayed aer a launch sequence of several seconds. The wireless
LAN connecon may take 10-15 seconds to be established.
Configuring the Mobile Tablet
The DT318CR may be congured using the ulies and methods dictated by
the soware operang system. The DT318CR should be congurable for various
properes such as user proles, network features, and several system elements.
Wireless Networking
Wireless LAN
The DT318CR is oen delivered with an embedded (user-inaccessible) 802.11ac
WLAN adapter equipped with a hidden custom antenna.
• Through the support of typical WLAN adapters, the DT318CR should be able to
detect all 802.11 access points in the vicinity for you to select the access point of
your choice for connecon.
• The SSID and WEP/WPA/WPA2 (if enabled) parameters on the DT318CR and the
access points have to match. The SSID is case-sensive and it is recommended
that you enable WEP/WPA/WPA2 encrypon (or advanced alternaves) for
secure access.
• When WEP/WPA/WPA2 is enabled, you may need to consult your network
administrator or your networking equipment literature to properly congure
associated sengs such as Authencaon mode, etc.
• Refer to the access point operang manuals for seng up the 802.11 access
points.
OPERATION
Powering ON and OFF
To acvate the DT318CR, push and quickly release the Power Buon. The display will
come on in a few seconds. To put the DT318CR in Standby mode, push and quickly
release the Power Buon. To turn the DT318CR o for extended storage, power
o safely using any soware funcon that “shuts down computer” provided in the
soware operang system.
NOTE:
The baery pack shipped with your tablet may be low in power—please use
the AC-DC adapter with the DT318CR when seng up for the rst me to fully
charge the baery pack, or use the oponal baery charger kit.
NOTE:
When the baery pack is charging, the blue-colored Baery LED should blink
slowly. If plugging in the AC-DC adapter does not trigger this blinking acvity
and the LED stays dark, the baery pack(s) may have been drained substanally.
Try unplugging/ replugging the AC-DC adapter to the DT318CR a few mes to
acvate the charging process.
NOTE:
To conserve power, use (push and quick release) the Power Buon to put the
tablet in “Standby” mode while not in use. Pushing briey on the same buon
will wake up the system within seconds.
NOTE:
Avoid using the Power Buon (“hold 4+ seconds” feature) to turn o the
tablet—this form of hardware shutdown is intended to be a means of recovery
from lockups, and not as normal operaon.
45
Bluetooth
The Bluetooth conguraon applicaon is enabled from the System Tray or from the
Windows Mobility Center. Follow the instrucons and opons provided within the
applicaon to congure and invoke Bluetooth connecvity with the corresponding
peripherals.
USING THE MOBILE TABLET
Peripherals Support
Through its USB port, the DT318CR supports a wide range of USB-based peripherals.
These peripherals are applicable for soware installaon, applicaons storage, data
storage, and system soware recovery and updates.
For More Support
Users can download the Tablet Modules Basic Operaon Guides from the DT
Research website.
67
Federal Communication Commission Interference
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protecon against harmful interference in
a residenal installaon. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instrucons, may cause harmful interference to radio communicaons.
However, there is no guarantee that interference will not occur in a parcular
installaon. If this equipment does cause harmful interference to radio or
television recepon, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Cauon: Any changes or modicaons not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules.
Operaon is subject to the following two condions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operaon.
This device and its antenna(s) must not be co-located or operang in
conjuncon with any other antenna or transmier.
This Class [B] digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du
Canada.
To Hold the Tablet
Le hand: grip the le back side of the tablet
with your le hand four index ngers, with
thumb resng on the top of the back side of the
tablet and palm securely against the back.
Right hand: grip the right back side of the tablet
with your right hand four index ngers, with
thumb resng on the top of the back side of the
tablet and palm securely against the back.
Other DT Research Tablet manuals
DT Research
DT Research DT395GS Assembly instructions
DT Research
DT Research DT390i Assembly instructions
DT Research
DT Research DT302RP Assembly instructions
DT Research
DT Research DT365 Assembly instructions
DT Research
DT Research DT361AM Assembly instructions
DT Research
DT Research DT311Y Assembly instructions
DT Research
DT Research WebDT 360 Assembly instructions
DT Research
DT Research DT313Y Assembly instructions
DT Research
DT Research 301SY Assembly instructions
DT Research
DT Research DT362GL Assembly instructions
DT Research
DT Research 340Q Assembly instructions
DT Research
DT Research 524T Assembly instructions
DT Research
DT Research DT313T Assembly instructions
DT Research
DT Research DT395BT Assembly instructions
DT Research
DT Research DT382GL Assembly instructions
DT Research
DT Research 313Y/MD Assembly instructions
DT Research
DT Research 302MD Assembly instructions
DT Research
DT Research DT301C Assembly instructions
DT Research
DT Research DT370CR Assembly instructions
DT Research
DT Research DT361DM Assembly instructions
Popular Tablet manuals by other brands
Laser
Laser MID-1060 Quick operation guide
MUNBYN
MUNBYN IRT09J Easy setup guide
Motorola
Motorola MC3090R - Win CE 5.0 Professional 520 MHz quick start guide
Dell
Dell Latitude ST Setup and features information
Lenovo
Lenovo IdeaTab S6000L Hardware Maintenance Manual
Venturer
Venturer WT9L11 quick start guide
