Dimplex XHD23 User manual
Service Manual
Models
XHD23L/XHD23G
XHD26L/XHD26G
XHD28L/XHD28G
XHD33L/XHD33G
DF26L-PRO
DF26DWC-PRO
DF28L-PRO
DF28DWC-PRO
Part Number
6909940XXX
6913820XXX
6909850XXX
6913830XXX
6909970XXX
6913840XXX
6913820XXX
6913830XXX
6913840XXX
6910090XXX
7401050100R05
IMPORTANT SAFETY INFORMATION: Always read this manual rst before attempting to service this rebox.
For your safety, always comply with all warnings and safety instructions contained in this manual to prevent
personal injury or property damage.
2 www.dimplex.com
Always use a qualied technician or service agency to repair this rebox.
!NOTE: Procedures and techniques that are considered important enough to emphasize.
CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the equipment.
WARNING: Procedures and techniques which, if not carefully followed, will expose the user to the risk of re, serious
injury, or death.
XHD Replacement Parts List 1 ..........................................3
XHD Replacement Parts List 2 ..........................................4
DF-PRO Replacement Parts List ........................................5
Wiring Diagrams .....................................................6
Accessing Top Components ...........................................7
Accessing Bottom components.........................................7
Power Cord Replacement..............................................8
Main Control Board Replacement .......................................8
Heater Assembly Replacement .........................................9
Touchpad Replacement ...............................................9
Flicker Motor Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Flicker Rod Replacement .............................................10
Flame Base LED Strip Replacement ....................................11
Media Tray / Media LED Strip Replacement ..............................11
Flame Screen Replacement ...........................................12
Log Set Replacement ................................................12
Troubleshooting Guide ...............................................13
Table of Contents
3
Exploded Parts Diagram
Replacement Parts List
XHD23 MOD 0-A
XHD26 MOD 0-B
XHD28 MOD 0-A
1. Heater Assembly ......................2203730300RP
2. Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . 2100250700RP
3. Main Control Board Logs ................3001840100RP
Media ...............................3001840200RP
4. Power Cord ..........................4100190600RP
5. Touchpad ............................6700600100RP
6. Thermistor ...........................3001560900RP
7. Flicker Motor. . . . . . . . . . . . . . . . . . . . . . . . . .3000240200KIT
8. Flicker Rod XHD23. . . . . . . . . . . . . . . . . . . . . 5903090200RP
XHD26 & XHD28. . . . . . . . . . . . . 5903090100RP
9. Flame LED Strip XHD23 ...............3002200100RP
XHD26 & XHD28 .......3002200200RP
10. Flame Base LEDs XHD23L & XHD26L ....3001880100RP
XHD28L . . . . . . . . . . . . . 3001880200RP
11. Media LED Strip XHD23G ...............3001570100RP
XHD26G ...............3001570700RP
XHD28G ...............3001570300RP
12. Flame Screen XHD23 ..................5902580400RP
XHD26 ..................5902580500RP
XHD28 ..................5902580600RP
13. Logset XHD23L .......................0442330100RP
XHD26L .......................0442220100RP
XHD28L .......................0442300100RP
14. Media Tray XHD23G ...................0442320100RP
XHD26G ...................0442280100RP
XHD28G ...................0442310100RP
15. Medium Ice Chunks (Media Models) .......1400150100RP
16. Large Ice Chunks (Media Models) . . . . . . . . . 1400130400RP
17. Front Glass XHD23 ....................5903150100RP
XHD26 ....................5903070100RP
XHD28 ....................5903160100RP
18. Remote Control .......................6700590200RP
19. Mounting Hardware (XHD26). . . . . . . . . . . . . 9602100100RP
20. Felt Feet Pads ........................8600140101RP
12
17
1
2
3
4
10
7
13
8
9
5
6
18
19
4 www.dimplex.com
Exploded Parts Diagram
Replacement Parts List
XHD23 MOD B+
XHD26 MOD C+
XHD28 MOD B+
XHD33 ALL MODS
1. Heater Assembly ......................2203610700RP
2. Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . 2100250700RP
3. Main Control Board Logs ................3001840100RP
Media ...............................3001840200RP
4. Power Cord ..........................4100190700RP
5. Touchpad ............................6700600100RP
6. Thermistor ...........................3001560800RP
7. Flicker Motor. . . . . . . . . . . . . . . . . . . . . . . . . .3000240200KIT
8. Flicker Rod XHD23. . . . . . . . . . . . . . . . . . . . . 5903090200RP
XHD26 & XHD28. . . . . . . . . . . . . 5903090100RP
XHD33. . . . . . . . . . . . . . . . . . . . . 5903090300RP
9. Flame LED Strip XHD23 ...............3002200100RP
XHD26 & XHD28 .......3002200200RP
XHD33 ...............3002200300RP
10. Flame Base LEDs XHD23L & XHD26L ....3001880100RP
XHD28L . . . . . . . . . . . . . 3001880200RP
XHD33L . . . . . . . . . . . . . 3001880300RP
11. Media LED Strip XHD23G. . . . . . . . . . . . . . . 3001570100RP
XHD26G . . . . . . . . . . . . . . . 3001570700RP
XHD28G . . . . . . . . . . . . . . . 3001570300RP
XHD33G (2) ............3001960100RP
12. Flame Screen XHD23 ..................5902580400RP
XHD26 ..................5902580500RP
XHD28 ..................5902580600RP
XHD33 ..................5902580700RP
13. Logset XHD23L .......................0442330100RP
XHD26L .......................0442220100RP
XHD28L .......................0442300100RP
XHD33L .......................0442460100RP
14. Media Tray XHD23G ...................0442320100RP
XHD26G ...................0442280100RP
XHD28G ...................0442310100RP
XHD33G ...................0442470100RP
15. Medium Ice Chunks (Media Models) .......1400150100RP
16. Large Ice Chunks (Media Models) . . . . . . . . . 1400130400RP
17. Front Glass XHD23 ....................5903150100RP
XHD26 ....................5903070100RP
XHD28 ....................5903160100RP
XHD33 ....................5903210100RP
18. Remote Control .......................6700590200RP
19. Mounting Hardware (XHD26). . . . . . . . . . . . . 9602100100RP
20. Felt Feet Pads ........................8600140101RP
12
17
1
2
3
4
10
7
13
8
9
5
6
18
5
DF-PRO Replacement Parts List
1. Heater Assembly ......................2203730300RP
2. Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . 2100250700RP
3. Main Control Board Logs ................3001840100RP
DWC ...............3001840200RP
4. Power Cord ..........................4100190600RP
5. Touchpad ............................6700600100RP
6. Thermistor ...........................3001560800RP
7. Flicker Motor. . . . . . . . . . . . . . . . . . . . . . . . . .3000240200KIT
8. Flicker Rod . . . . . . . . . . . . . . . . . . . . . . . . . . . 5903090100RP
9. Flame LED Strip. . . . . . . . . . . . . . . . . . . . . . . 3002200200RP
10. Flame Base LEDs DF26L-PRO ..........3001880100RP
DF28L-PRO . . . . . . . . . . 3001880200RP
11. Media LED Strip DF26DWC-PRO. . . . . . . . . 3001570700RP
DF28DWC-PRO . . . . . . . . . 3001570300RP
12. Flame Screen DF26-PRO ...............5902580500RP
DF28-PRO ...............5902580600RP
13. Logset DF26L-PRO ....................0442220100RP
DF28L-PRO ....................0442300100RP
14. Media Tray DF26DWC-PRO .............0442280100RP
DF28DWC-PRO .............0442310100RP
15. Medium Ice Chunks (DWC Models) ........1400150100RP
16. Large Ice Chunks (DWC Models). . . . . . . . . . 1400130400RP
17. Driftwood (DWC Models) ................0441820100RP
18. River Rock (DWC Models) . . . . . . . . . . . . . . . 1400080301RP
19. Front Glass DF26-PRO .................5903070100RP
DF28-PRO .................5903160100RP
20. Remote Control .......................6700590200RP
21. Mounting Hardware (DF-26-PRO) .........9602100100RP
22. Felt Feet Pads ........................8600140101RP
9
1
2
34
19
20
21
5
6
7
8
12
10
14
18
16
15
17
Exploded Parts Diagram
6 www.dimplex.com
Wiring Diagram
Logset or Media Bed LEDs
On log models only
M
AC / DC
120V / 12V
~
IR
REMOTE
M
L
LOGSET ASSEMBLY
FLAME BASE OR MEDIA BED RBG STRIP
FLAME LED LIGHTS
FLICKER
MOTOR
BLOWER
MOTOR
IR EYE/DISPLAY/CAPACITIVE
TOUCH CONTROL BOARD
MAIN CONTROL
BOARD
G
POWER
SUPPLY
NTC
CUTOUT
N
XHD23 MOD 0-A
XHD26 MOD 0-B
XHD28 MOD 0-A
ALL DF-PRO
XHD23 MOD B
XHD26 MOD C
XHD28 MOD B
7
Accessing Top Components
Tools Required: Phillips head screwdriver
WARNING: If the rebox was operating prior to
servicing, allow at least 10 minutes for the heating
elements to cool o to avoid accidental burning of skin.
WARNING: Disconnect power before attempting any
maintenance to reduce the risk of electric shock or injury
to persons.
1. Unhook the front glass to remove it by pulling it up
slightly and pulling it out. Set it aside in a safe place.
2. Remove the rebox from the mantel by removing the
retaining screws that secure the rebox to the mantel.
These may be located on the inside of the rebox near
the front, or behind the rebox if it is secured with L-
brackets.
3. Unfasten the top panel by removing the 12 screws lo-
cated around the periphery of the top panel. There are
2 screws on each side, 3 on the back, and 5 at the very
top, directly behind the front ange. Some units may
have 6 screws on the top, totaling 13 screws. (Figure 1)
4. Slide the top panel toward the back to release it.
5. Carefully lay the rebox on its back and lay the top
cover at so that the attached components are acces-
sible.
Accessing Bottom Components
Tools Required: Phillips head screwdriver
WARNING: If the rebox was operating prior to
servicing, allow at least 10 minutes for the heating
elements to cool o to avoid accidental burning of skin.
WARNING: Disconnect power before attempting any
maintenance to reduce the risk of electric shock or injury
to persons.
1. Unhook the front glass to remove it by pulling it up
slightly and pulling it out. Set it aside in a safe place.
2. Remove the rebox from the mantel by removing the
retaining screws that secure the rebox to the mantel.
These may be located on the inside of the rebox
near the front, or behind the rebox if it is secured with
L-brackets.
3. Unfasten the bottom panel by removing the 11 screws
located on the back and sides of the bottom panel.
There are 3 screws on the back, and 4 screws on each
side. Note that the two middle screws on each side
are longer, and hold the media tray or log set in place.
(Figure 2)
!NOTE: When reinstalling the base panel, align the
2 middle screw holes on each side of the logset/media
tray with the corresponding holes on the base panel to
ensure that the logset or media tray are properly
axed. (Figure 5)
Figure 1
Figure 2
8 www.dimplex.com
4. Carefully lay the replace on its back.
5. Remove the bottom panel and set it aside.
!NOTE: On the XHD28G/DF28DWC-PRO, the
media bed lights are attached to this bottom panel. You
can disconnect these lights to have better access to the
components in the rebox.
!NOTE: The log set/media tray has a wire attached
to the unit which can be temporarily disconnected for
easier access.
Most components can now be accessed for service.
However, if you wish to have further access to the
components, complete the following steps.
6. Remove the ame screen retaining brackets by
removing the 2 screws on each side of the rebox that
hold each bracket (4 screws total). (Figure 5)
7. Carefully slide the ame screen down toward the base
of the rebox and set it aside during service.
!NOTE: When reinserting the ame screen, ensure
that the upper portion is inserted all the way to the top.
Power Cord Replacement
Tools Required: Phillips head screwdriver
Pliers
7mm Wrench
WARNING: If the rebox was operating prior to
servicing, allow at least 10 minutes for the heating
elements to cool o to avoid accidental burning of skin.
WARNING: Disconnect power before attempting any
maintenance to reduce the risk of electric shock or injury
to persons.
1. Follow the instructions for accessing the top
components on page 8.
2. Disconnect the wires from the powercord, noting their
original locations. Use wrench to remove gold nut that
secures the green grounding wire to the body of the
rebox, along with the silver ring. Cut the cable ties as
needed to remove the wires.
3. With pliers, grasp the power cord strain relief grommet
from inside the back of the bottom panel and push
while twisting to remove.
4. Install the new power cord and reconnect wires as
before. Refer to the wiring diagram if needed. Ensure
that they are secure and the wires cannot be pulled out
of the wire connector.
WARNING: Ensure wires do not come in contact
with moving parts by securing wires in cable ties or
electrical tape.
5. Reassemble the rebox.
Main Control Board Replacement
Tools Required: Phillips head screwdriver
Pliers
WARNING: If the rebox was operating prior to
servicing, allow at least 10 minutes for the heating
elements to cool o to avoid accidental burning of skin.
WARNING: Disconnect power before attempting any
maintenance to reduce the risk of electric shock or injury
to persons.
1. Follow the instructions for accessing the top
components on page 8.
!NOTE: It is recommended to take a picture of the
wiring connections on the main control board prior to
starting to ensure that all wires are reconnected to the
correct place on the board.
2. Disconnect all wire leading into the main control board.
It may be helpful to use pliers to disconnect the ag
connectors. Cut the cable ties as needed to remove the
wires.
3. Using pliers, pinch each of the four plastic standos to
depress the tabs while gently lifting the main control
board to release it. (Figure 3)
4. Properly orient and install the new main control board.
5. Reconnect the wiring. Refer to the wiring diagram if
needed.
WARNING: Ensure wires do not come in contact
with moving parts by securing wires in cable ties or
electrical tape.
6. Reassemble the rebox.
Figure 3
9
Power Supply Replacement
Tools Required: Phillips head screwdriver
Pliers
WARNING: If the rebox was operating prior to
servicing, allow at least 10 minutes for the heating
elements to cool o to avoid accidental burning of skin.
WARNING: Disconnect power before attempting any
maintenance to reduce the risk of electric shock or injury to
persons.
1. Follow the instructions for accessing the top
components on page 8.
2. Locate the power supply and disconnect the wiring
connections, noting their original locations. Cut the
cable ties as needed to remove the wires.
3. Remove the 4 screws that secure the power supply
holder.
4. Properly orient and position the new power supply and
secure it by screwing the power supply holder into its
place.
5. Reconnect the wiring. Refer to the diagram if needed.
WARNING: Ensure wires do not come in contact
with moving parts by securing wires in cable ties or
electrical tape.
6. Reassemble the rebox.
Heater Assembly Replacement
Tools Required: Phillips head screwdriver
Pliers
WARNING: If the rebox was operating prior to
servicing, allow at least 10 minutes for the heating
elements to cool o to avoid accidental burning of skin.
WARNING: Disconnect power before attempting any
maintenance to reduce the risk of electric shock or injury to
persons.
1. Follow the instructions for accessing the top compo-
nents on page 8.
!NOTE: It is recommended to take a picture of
the wiring connections on the main control board and
heater assembly prior to starting to ensure that all wires
are reconnected to the correct place during service.
2. Disconnect the wiring connections noting their origi-
nal locations. There are 3 on the main control board,
2 wires on the blower motor, and one wire connected
with a wire connector. Cut the cable ties as needed to
remove the wires.
3. Remove the 4 screws that secure the heater assembly
to the top panel. This must be done from the opposite
side of the top panel. (Figure 5)
4. Properly orient and install the new heater assembly,
and screw it into place.
5. Reconnect the wires. See wiring diagram if needed.
WARNING: Ensure wires do not come in contact
with moving parts by securing wires in cable ties or
electrical tape.
6. Reassemble the rebox.
Touchpad Replacement
Tools Required: Phillips head screwdriver
WARNING: If the rebox was operating prior to
servicing, allow at least 10 minutes for the heating
elements to cool o to avoid accidental burning of skin.
WARNING: Disconnect power before attempting any
maintenance to reduce the risk of electric shock or injury to
persons.
1. Follow the instructions for accessing the top
components on page 8.
2. Locate and disconnect the connection from the
touchpad to the main control board.
3. Remove screws on either side of the touchpad to
release it. (Figure 4)
4. Properly orient the new touchpad and reinsert screws.
5. Reconnect the new touchpad.
6. Reassemble the rebox.
Figure 4
10 www.dimplex.com
Flicker Motor Replacement
Tools Required: Phillips head screwdriver
Pliers
Side cutters
WARNING: If the rebox was operating prior to
servicing, allow at least 10 minutes for the heating
elements to cool o to avoid accidental burning of skin.
WARNING: Disconnect power before attempting any
maintenance to reduce the risk of electric shock or injury to
persons.
1. Follow the instructions for accessing the bottom
components on pages 8-9.
2. Remove the right side icker rod retaining bracket by
unscrewing the two corresponding screws on the back
of the rebox. (Figure 5)
3. Pull the icker motor out from the rubber coupling
attached to the icker rod.
4. Remove the two screws that ax the icker motor to
the bracket.
5. Cut the ve wires as close as possible to the icker
motor.
6. Cut wire leads from the new icker motor to 3 1/2
inches long.
7. Using one of the supplied wire connectors, connect the
yellow wire from the new icker motor with the yellow
wire cut from the old icker motor.
8. Secure the wire connector by crimping the 3M symbol
with pliers. Pull on both wires to ensure a strong
connection.
9. Repeat the process for the 4 remaining wires, ensuring
that all wires are paired by colour in each connector.
10. Attach new icker motor to the retaining bracket.
11. Insert stem from icker rod into the rubber grommet.
12. Reattach the icker rod retaining bracket.
13. Reassemble the rebox.
Remove this bracket when
changing icker motor
Remove this bracket when
changing icker rod
Media bed/Log
set screws Flame screen retaining
bracket screws
Heater assembly screws
Flicker Rod Replacement
Tools Required: Phillips head screwdriver
WARNING: If the rebox was operating prior to
servicing, allow at least 10 minutes for the heating
elements to cool o to avoid accidental burning of skin.
WARNING: Disconnect power before attempting any
maintenance to reduce the risk of electric shock or injury to
persons.
1. Follow the instructions for accessing the bottom
components on pages 8-9.
2. Remove the left side icker rod retaining bracket by
unscrewing the two screws from the back of the rebox.
(Figure 5)
3. Pull the old icker rod out from the rubber grommet.
4. Insert new icker rod.
5. Place bracket over the end of the new icker rod and
reax the bracket to the rebox.
6. Reassemble the rebox.
Figure 5
This manual suits for next models
12
Table of contents
Other Dimplex Indoor Fireplace manuals
Dimplex
Dimplex TIMRA TMR15 Installation guide
Dimplex
Dimplex DF2524L User manual
Dimplex
Dimplex Pro Series User manual
Dimplex
Dimplex Amesbury AME20 User manual
Dimplex
Dimplex DFI2309 User manual
Dimplex
Dimplex Nicole User manual
Dimplex
Dimplex EWMC-CC-SS User manual
Dimplex
Dimplex DF2624L User manual
Dimplex
Dimplex VCX1525 User manual
Dimplex
Dimplex MULTIFIRE DF3215 User manual
Dimplex
Dimplex PF2325 User manual
Dimplex
Dimplex BLF34 User manual
Dimplex
Dimplex BF9000 User manual
Dimplex
Dimplex DF3033ST User manual
Dimplex
Dimplex VF5452L User manual
Dimplex
Dimplex SIL48 User manual
Dimplex
Dimplex Wesley Side Control User manual
Dimplex
Dimplex ENGDL20 S E User manual
Dimplex
Dimplex SP320 User manual
Dimplex
Dimplex Revillusion RBF24DLX User manual
Popular Indoor Fireplace manuals by other brands
Brigantia
Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual
Nordpeis
Nordpeis Bergen Installation and user manual
Superior
Superior BCT2536TMN Installation and operation instructions
Quadra-Fire
Quadra-Fire 5100I-GD-B owner's manual
Renaissance
Renaissance RUMFORD 1000 user manual
Lacunza
Lacunza IV-800 Instruction book
Baxi
Baxi 940 Installer and owner guide
Dru
Dru Maestro 60/2 Tall RCH installation manual
Diamond Fireglass
Diamond Fireglass SS-O22 General assembly, installation, and operation instructions
HearthStone
HearthStone Windsor Bay 8830 Owner's manual and installation guide
Napoleon
Napoleon ASCENT B42 quick start guide
Enviro
Enviro E33GI owner's manual
Smeg
Smeg L30 FABE Installation & user's instructions
KEDDY
KEDDY K700 Installation instructions care and firing instructions
Godin
Godin 3451 manual
Jøtul
Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions
Austro Flamm
Austro Flamm Heidi Back 2.0 945048 operating manual
Desa
Desa CCFPDFT Owner's operating & installation manual