Dimplex Pro Engine series Instruction Manual

Dimplex Pro Engine Range

Models: ENG56-400 E, ENG68-400 E, ENG56-600 E

These instructions should be read carefully and

retained for future use. Note also the information

presented on the appliance.

OPERATING

INSTRUCTION MANUAL

08/53883/0 ISSUE 2 OCN 10949

EN: This product is only suitable for well insulated rooms or occasional use. DE: Dieses Produkt ist nur für gut isolierte Bereiche oder

gelegentliche Verwendung geeignet. FR: Ce produit convient uniquement à des endroits bien isolés ou pour un usage occasionnel.

IT: Questo prodotto è adatto solo per spazi ben isolati o per uso occasionale. ES: Este producto sólo es adecuado para espacios

bien aislados o un uso ocasional. NL: Dit product is uitsluitend geschikt voor goed geïsoleerde ruimten of voor sporadisch gebruik.

PL: Produkt ten jest odpowiedni wyłącznie do dobrze odizolowanych miejsc lub do okazjonalnego użytku. NO: Dette produktet

egner seg kun for godt isolerte rom eller sporadisk bruk. RO: Acest produs este adecvat exclusiv spaţiilor bine ventilate sau utilizării

ocazionale. CZ: Tento výrobek je vhodný pouze do dobře izolovaných prostor nebo k příležitostnému použití. DK: Dette produkt

er kun egnet til velisolerede rum eller lejlighedsvis brug. PT: Este produto somente é adequado para espaços bem isolados ou

uso ocasional. SE: Denna produkt är endast avsedd för välisolerade utrymmen eller tillfällig användning. FI: Tämä tuote soveltuu

ainoastaan hyvin eristettyihin tiloihin tai satunnaiseen käyttöön. SK: Tento výrobok je vhodný len pre dobre izolované priestory alebo

na občasné použitie. SI: Ta izdelek je primeren le za dobro izolirane prostore ali za občasno uporabo. HR: Ovaj proizvod je pogodan

samo za dobro izolirane prostore ili povremenu upotrebu. HU: Ez a termék csak jól szigetelt terekhez vagy eseti használatra alkalmas

The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic

Compatibility (EMC) EN55014, EN60555-2 and EN60555-3. These cover the essential requirements of EEC Directives

2014/30/EU and 2014/35/EU

CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE INJURY AND/OR

DAMAGE AND MAY INVALIDATE YOUR GUARANTEE

Important Safety Advice

When using electrical appliances, basic precautions should always be followed to reduce the

risk of ﬁre, electrical shock and injury to persons, including the following:

If the appliance is damaged, check with the supplier before installation and operation.

Do not use outdoors.

Do not use in the immediate surroundings of a bath, shower or swimming pool.

Do not locate the appliance immediately below a ﬁxed socket outlet or connection box.

Caution: Some parts of this product can become very hot and cause burns. Particular attention

has to be given where children and vulnerable people are present. This instruction can be found

at www.dimplex.co.uk

Warning: This heater must not be used for anything other than normal domestic household

purposes in the country where it was purchased from a recognised commercial retailer.

This appliance can be used by children aged from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in a safe way and understand

the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance

shall not be made by Children without supervision.

Children of less than 3 years should be kept away unless continuously supervised. Children

aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it

has been placed or installed in its intended normal operating position and they have been given

supervision or instruction concerning use of the appliance in a safe way and understanding the

hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate

and clean the appliance or perform user maintenance.

Warning: This appliance must be earthed.

The use of an extension lead or multi-plug adaptor is not advised when connecting this product

to the mains. Connection through these devices could lead to a risk of overloading, overheating

and even ﬁre at the extension lead or adaptor due to inadequate connection quality.

This heater must be used on an ~alternating current supply (~) only and the voltage marked on

the heater must correspond to the supply voltage.

Do not use this appliance in series with a thermal control, a program controller, a timer or any

other device that switches on the heat automatically, since a ﬁre risk exists when the appliance

is accidentally covered or displaced.

DO NOT use the heater on deep pile carpets or the long hair type of rugs, or less than 750mm

(30”) away from any overhanging surface. Keep combustible materials such as drapes and

other furnishings clear from the front, sides and rear of the heater. Do not use heater to dry your

laundry.

In the event of a fault unplug the appliance. Unplug the appliance when not required for long

periods.

The appliance must be positioned so that the plug is accessible. If the supply cord is damaged

it must be replaced by the manufacturer or service agent or a similarly qualiﬁed person in order

to avoid a hazard. Keep the supply cord away from the front of the appliance.

Warning: In order to avoid overheating, do not cover the appliance. Do not place material or

garments on the appliance, or obstruct the air circulation around the appliance, for instance by

curtains or furniture, as this could cause overheating and a ﬁre risk.

The appliance carries a DO NOT COVER warning

Warning: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this

appliance must not be supplied through an external switching device, such as a timer, or

connected to a circuit that is regularly switched on and off by the utility.

Thank you for choosing a Dimplex electric ﬁre

Dimplex PRO Chassis

Models: Engine 56 - 400 E / Engine 68 - 400 E / Engine 56 - 600 E

Only use ﬁltered water in this appliance.

Always ensure that the appliance is sitting on a level surface.

Although this heater complies with safety standards, we do not recommend its use on deep pile carpets or

on long hair type of rugs.

Please note: Used in an environment where background noise is very low, it may be possible to hear a sound

which is related to the operation of the ﬂame effect. This is normal and should not be a cause for concern.

If this product experiences a power surge for whatever reason the product may cut-out. This is a normal safety

feature and the product will resume operation after 30 seconds.

Once installed, never move this appliance or lay on its back, without draining the water from sump and water

tank.

If you intend not using the appliance for longer than 2 weeks, drain the water from sump and water tank and

dry the sump.

The water tank, sump, sump lid, tank cap and air ﬁlters must be cleaned once every two weeks, particularly

in hard water areas.

The appliance should never be operated if the lamps are not working.

The lamps should be regularly inspected as described under ‘Maintenance’ and ‘Changing lamps’.

The sump and the water tank in this product are treated with a biocidal product, Silver Biocide. This conforms

with the latest relevant ISO standard.

Technical Information

Model No: ENG56-400 E, ENG68-400 E, ENG56-600 E

with electronic room temperature control.

General Information

Heat Output 230V 240V

Nominal Heat Output PNom 1.8 2.0 kW

Minimum Heat Output Pmin 0.9 1.0 kW

Maximum Continuous Heat Output Pmax 1.8 2.0 kW

Auxiliary Electricity Consumption

In Standby Mode PNom 0.45 0.48 W

Installation Instructions

This section describes how to set up your ﬁre.

BEFORE YOU START

1. Ensure that all packing items are removed (read any warning labels carefully) and retain all packing for

possible future use e.g. in the event of moving house or returning the appliance to your supplier.

2. Before connecting the appliance, check that the supply voltage is the same as that stated on the heater.

Installation into a Fireplace Mantle

●When installing this appliance into a ﬁreplace mantle please ensure that you choose a mantle suitable for

your appliance (Fig 17). There is to be an air vent at the front of the ﬁreplace mantle of at least 100cm2.

It is essential to ensure that air can circulate into the appliance – otherwise the Opti-myst ﬂame effect will

not operate correctly. This pathway for air must not be obstructed

●Remove the 4 spacing brackets on the front of the appliance (Fig 18)

●Slide the appliance into the ﬁreplace mantle fully from the back ensuring that it is sitting in the center of

the mantle. Using suitable screws (not supplied) screw ﬁx the appliance in place (Fig 19)

●Be sure to position the ﬁreplace within 1m of a power outlet (Fig 20)

Installation into a wall or recess cavity

●Note the product dimensions in Fig 1 and build a suitable structure for the appliance to ﬁt into within 1m

of a power outlet (Fig21). Using suitable screws (not supplied) screw ﬁx the appliance in place

●Note the venting slots in the appliance. There are located at the front base and under the appliance

●Build the wall up against the appliance using the spacing brackets as a guide.

●There is to be an air vent at the front of the structure of at least 88cm2. It is essential to ensure that air can

circulate into the appliance – otherwise the Opti-myst ﬂame effect will not operate correctly. This pathway

for air must not be obstructed. For examples of air vents in a wall or recess cavity see Fig 22 and Fig 23.

PLEASE ENSURE CHILDREN DO NOT CLIMB, HANG OR STAND ON THIS PRODUCT.

WARNING: THE APPLIANCE IS PROVIDED WITH A TIPPING RESTRAINT, THIS RESTRAINT IS NOT A

SUBSTITUTE FOR PROPER ADULT SUPERVISION. THIS RESTRAINT MAY PROVIDE PROTECTION

AGAINST TIPPING FURNITURE. DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE. FAILURE TO

DETACH THIS RESTRAINT BEFORE MOVING FURNITURE MAY RESULT IN INJURY AND DAMAGE.

This product is provided with a ‘Tipping Restraint Kit’ as shown in Fig 1, to prevent the product accidentally

tipping over. Fitting Instructions are supplied with this kit please follow these instructions carefully.

Connecting the Transducer Unit + Lamps

1. Release the two red tabs by turning them by 90 degrees (Fig 2)

2. Lift out the Sump Nozzle (Fig 3)

3. Insert lamps into lamp holders (Fig 4), carefully locating the pins into the holes (Fig 4a)

4. Push lamps ﬁrmly into place

5. Place the Transducer Unit into the sump and join the cable to the connector on the sump (Fig 5)

6. To ensure that the Transducer Unit is correctly placed in the sump, the tab on the Transducer Unit should

be lined up with the moulded recess in the sump (Fig 5a).

7. Ensure that the cable is not placed above the disc on the Transducer Unit (Fig 5b). To prevent the cable

becoming pinched between the nozzle and the sump, place the cable in the slot in the wall of the sump.

8. Replace the Sump Nozzle and secure it by turning the two red tabs by 90 degrees (Fig 6)

Filling the Water Tank

9. Place Water Tank in sink and remove cap (turn anti-clockwise to open) (Fig 7)

10. Fill Water Tank with ﬁltered tap water only. This is necessary to prolong the life of the ﬂame and smoke

producing unit. The water should be ﬁltered through a conventional domestic water ﬁlter unit and the ﬁlter

should be replaced regularly. Distilled water must not be used.

11. Screw the cap back on – do not overtighten.

12. Place the Water Tank in the Sump, with the tank cap facing down and the ﬂat side of the tank facing

outward (Fig 8)

Assembling the ﬁre

13. Place the Fuelbed on top of the Water Tank and Mist Nozzle (Fig 9)

Operating The Product

WARNING: FAILURE TO FOLLOW THESE OPERATING INSTRUCTIONS MAY RESULT IN INJURY AND/

OR DAMAGE.

MANUAL CONTROLS

The manual controls are located beneath the hinged ﬂap. (Fig.10 for Manual Control lay out)

Switch ‘A’:- Controls the electricity supply to the Fire.

Note: This switch must be in the ‘ON’ ( I ) position for the Fire to operate either with or without heat.

Switch ‘B’:- Press once to turn on the ﬂame eect. This will be indicated by an audible beep. Although

the main lights operate immediately it will take a further 30 seconds before the ﬂame eect starts.

Press to put ﬁre in to standby mode. This will be indicated by one beep.

REMOTE CONTROL

The remote control is packed with 2 AA batteries in a bag. Lift o the battery cover on the back of the

remote control and insert the batteries taking note of the polarity.

Switching on the appliance

Press and hold the ENTER button for 3 seconds to activate the remote control. FIRE will be displayed and

ON will be blinking. Press ENTER to swtich on the appliance. To turn o the appliance press MENU so that

FIRE is blinking, press ENTER twice.

Adjust the Flame Setting

With the remote control activated press MENU once. FIRE will be blinking on the display. Press ENTER.

The current ﬂame setting will be displayed F1-F6. Press the UP and DOWN buttons to adjust the setting.

After you have selected your ﬂame setting press BACK twice to exit the menu and return to the home

screen.

Switching on the Heat

With the remote control activated press MENU once. FIRE will be blinking on the display. Press ADV once,

HEAT will be blinking. Press ENTER. The current heat setting will be displayed OFF LO HI. Press the UP

and DOWN buttons to adjust the setting. After you have selected your ﬂame setting press ENTER

Setting the Thermostat

The temperature shown on the display is the room temperature set point. This is the temperature that the

heater will maintain during the heating periods. If the room temperature is above this temperature then the

Modes of Remote Operation

User Timer: Provides greatest ﬂexibility to the user. Four times slots are available throughout the day and

these can be customised for each day of the week. See “How to adjust the timer modes” for instructions on

adjusting these from the factory default time periods & temperatures.

Manual Mode: This mode heats the room to the temperature you have set the remote control to.

Frost Protection: This mode will maintain a room temperature to 7ºC. This mode should be used to provide

protection against frost as indicated by the frost icon.

Choosing and Setting a Mode

User Timer - To re-programme the factory default Timer Modes:

Press Menu Button

Press ^ once to the schedule Icon is blinking. Press Enter

Press ^ Twice then press Enter

*Days of the weeks are now displayed at the top of the screen*

heater will not operate. The heater leaves the factory with this temperature set at 15ºC which represents a

typical comfortable room temperature. If you require a dierent room temperature then press either up or

down on the home screen until the display shows the temperature you require.

Thermal Safety Cut-out

A thermal safety cut-out is incorporated in the fan heater to prevent damage due to overheating. This can

happen if the heat outlet was restricted in any way. If the cut-out operates, unplug the heater from the

socket outlet and allow approximately 10 minutes before reconnecting. Before switching the heater back

on remove any obstruction that may be restricting the heat outlet, then continue normal operation.

CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance

must not be supplied through an external switching device, such as a timer, or connected to a switch that is

regularly switched on and off by the utility.

Setting the Date and Time

To set the date and time on the heater;

Press the Menu button

Press ^ button 4 times

Press Enter when the Date & Time icon is blinking

Press Enter to set Time

Press v and ^ to set the Hour, press Enter

Press v and ^ to set the Minutes, press Enter to conﬁrm the time

Press v and ^ to set the Day, press Enter

Press v and ^ to set the Month, press Enter

Press v and ^ to set the Year, press Enter to conﬁrm the date

Day 1 = Monday

Day 2 = Tuesday

Day 3 = Wednesday

Day 4 = Thursday

Day 5 = Friday

Day 6 = Saturday

Day 7 = Sunday

Press Enter to Modify Day 1 or Press ^ to navigate to the desired day and Press Enter to Select

P1 will be displayed on screen

Press Enter to select P1, to navigate to P2, P3 or P4 press ^ and press Enter to select

ON will be highlighted, press Enter to set the on Time

Press v or ^ to adjust the on Hour time, press Enter to Conﬁrm

Press v or ^ to adjust the on Minute time, press Enter to Conﬁrm

Press v or ^ to adjust the Temperature setting, press Enter to Conﬁrm

Press v or ^ to adjust the off Hour time, press Enter to Conﬁrm

Press v or ^ to adjust the off Minute time, press Enter to Conﬁrm

Press Enter to modify Programme P2, follow steps 5-12, Press ^ to skip to P3

Press Enter to modify Programme P3, follow steps 5-12, Press ^ to Skip to P4

Press Enter to modify Programme P4, follow steps 5-12

To copy newly programmed P1-P4 heating programmes to other days press the Enter button.

Copy will be displayed on screen

To copy to the next day in sequence, press ^ button. To deselect the next day in sequence press

Enter button.

The days of the week that are selected will be displayed at the top of the screen. The days that

have been deselected will not be visible (see Diagrams).

Press Enter to conﬁrm, backlight will ﬂash and return to home screen.

Getting the Desired Flame Effect

Using the remote control press MENU, FIRE on the display will be ﬂashing, press ENTER. The current setting

will be displayed. Press ^ or v to toggle between F1 and F6. F1 being the lowest setting and F6 being the

highest setting.

Generally the ﬂames appear more realistic when the ﬂame control is turned down.

Give the ﬂame generator time to react to changes you may make.

The ﬁre will use less water if the ﬂame effect is set to a lower level.

Do not tilt or move the ﬁre while there is water in the tank or sump.

Make sure that the ﬁre is on a level ﬂoor.

Customising the display

The maximum temperature set point on the product is 32ºC You have the option to reduce this set point. You

can also change ºC to ºF

Press the Menu button.

Press the ADV button twice - SP will be blinking.

Press Enter to conﬁrm.

Press v or ^ to choose between ºC and ºF.

Press Enter to conﬁrm.

Press v or ^ to choose your maximum temperature set point.

Press Enter to conﬁrm.

Press BACK three times to return to the home screen.

Adaptive Start

The built-in electronics in this appliance hava a learning function with regards to how long it takes to heat up

a room. Having learnt how quickly it can heat up your room, the appliance is able to turn on at just the right

time in order to get the room up to a comfortable temperature when you want it. For example, if you get up at

7am, you would normally have to guess when to turn the heating on in order for it to pre-heat the room in time.

Manual Mode - To choose a constant heat mode. This mode ignores the User Timer and maintains the

displayed temperature.

• Press Menu Button

• Press ^ twice to highlight the Hand icon

• Press Enter to Conﬁrm

• Use v and ^ to adjust to the desired temperature

Frost protect - Frost protect mode maintains a room temperature of 7ºC throughout a 24 hour period. This

mode should be used to provide protection against frost as indicated by the Frost icon.

• Press the Menu button

• Press ^ three times to highlight the snowﬂake icon

• Press Enter to conﬁrm

• Press v or ^ to exit this mode and enter manual mode.

1 Display Screen

2 ‘Menu’ Button

3 ‘Back’ Button

4 ‘Advance’ Button

5 ‘Up and Down’ Arrows

6 ‘Enter’ Button

Remote Control

Depending on how cold it is outside, this could mean the room is still cold when you have to get out of bed, or

mean that its been warm for half an hour before it needed to be. Adaptive Start means that if you select 21ºC

at 7am, the heater will turn on exactly when it needs to in order to meet this target, running for shorter periods

of time when the weather is mild, and ensuring the room is nice and warm in the winter.

The Adaptive Start function will automatically activate when you use the Timer Mode.

Maintenance

GENERAL TIPS

Only use ﬁltered tap water in this appliance.

Always ensure that the appliance is sitting on a level surface.

If you intend not using the appliance for longer than 2 weeks, remove and empty the sump and water tank.

Once installed, never move this appliance or lay on its back, without draining the water from sump and water

tank.

The appliance should never be operated if the lamps are not working.

The lamps should be regularly inspected as described under ‘Changing lamps’.

FILLING THE WATER TANK

When the water tank is empty, the ﬂame and smoke effect shuts off and you will hear 2 audible beeps, follow

these steps.

1. Press Switch ‘A’ to (0) (Fig.10)

2. Gently lift out the fuelbed and carefully set aside.

3. Remove the water tank by lifting upwards and outwards.

4. Place the water tank in sink and remove cap, Anti-clockwise to open. (Fig 7)

5. Fill tank with ﬁltered tap water only. This is necessary to prolong the life of the ﬂame and smoke producing

unit.

6. The water should be ﬁltered through a conventional domestic water ﬁlter unit and the ﬁlter should be

replaced regularly.

7. Screw the cap back on, do not over tighten.

8. Return the tank to the sump, with the tank cap facing down and the ﬂat side of the tank facing outward

(Fig 8)

9. Gently place the fuelbed back into position. (Fig 9)

10. Press Switch ‘A’ to ‘ON’ (I) position (Fig.10)

CHANGING LAMPS

If the ﬂame and smoke effect appears grey or colourless it may be that one or more lamps have failed.

You can check for lamp failure as follows.

1. Leaving the ﬂame effect on, lift out the fuelbed and water tank.

2. It should be possible to view the lamps with the nozzle in place and observe which one needs to be

changed.

3. Put Switch ‘A’ in the ‘OFF’ position, and unplug the ﬁre from the mains.

4. Leave the appliance for 20 minutes to allow the lamps to cool down before removing them.

5. Remove the sump as described in the Cleaning Section.

6. Remove the defective lamp, by gently lifting vertically and disengaging the pins from the lamp holder,

(Fig.4 and 4a).

7. Replace with an OPTIMYST, 12V, 45W, Gu5.3 base, 8º beam angle, coloured lamp. (Purchased from

www.dimplex.co.uk/spares)

8. Carefully insert the two pins of the new lamp into the two holes in the lamp holder. Push ﬁrmly in place.

(Fig.4 and 4a).

9. Replace the sump, nozzle, water tank and fuelbed.

CLEANING

Warning – Always press Switch ‘A’ to the ‘OFF’ (0) position (Fig.10) and disconnect from the power supply

before cleaning the ﬁre.

We recommend cleaning the following components once every 2 weeks, particularly in hard water areas:-

Water Tank, Sump, Nozzle, Tank cap and seal, Air ﬁlter.

For general cleaning use a soft clean duster – never use abrasive cleaners.

To remove any accumulation of dust or ﬂuff the soft brush attachment of a vacuum cleaner should occasionally

be used to clean the outlet grille of the fan heater.

Water tank

1. Remove water tank, as described earlier, put into sink and empty water.

2. Using the supplied brush gently rub the inside surfaces of the cap paying particular attention to the rubber

ring in the outer groove and the centre rubber seal.

3. Put a small quantity of washing up liquid into the tank, reﬁt the cap and shake well, rinse out until all traces

of washing up liquid are gone.

4. Reﬁll with ﬁltered tap water only, replace the cap, do not overtighten.

Sump

1. Press Switch ‘A’ to the ‘OFF’ (0) position

2. Gently lift out the fuelbed and place carefully on the ground.

3. Remove the water tank by lifting upwards.

This manual suits for next models

Table of contents

Other Dimplex Indoor Fireplace manuals

Dimplex

Dimplex CHERITON COAL User manual

Dimplex

Dimplex SP16UK-E User manual

Dimplex

Dimplex CAS500 User manual

Dimplex

Dimplex DS7420 User manual

Dimplex

Dimplex VERDI VER20 User manual

Dimplex

Dimplex CDFI400RH User manual

Dimplex

Dimplex DWF5252B User manual

Dimplex

Dimplex DNV20AB User manual

Dimplex

Dimplex Optiflame BF3600 User manual

Dimplex

Dimplex BF36 Series User manual

Dimplex

Dimplex CHERITON LED CHT20 User manual

Dimplex

Dimplex SF3202 User manual

Dimplex

Dimplex X40003BK User manual

Dimplex

Dimplex BF45DXP User manual

Dimplex

Dimplex CASSETTE 400 User manual

Dimplex

Dimplex Featherston GDS26L5-1152LR User manual

Dimplex

Dimplex DFG3033 User manual

Dimplex

Dimplex Opti-Suite2Go2 User manual

Dimplex

Dimplex BF33STP Quick start guide

Dimplex

Dimplex LAGsu User manual

Dimplex

Dimplex Revillusion RLG20 EU User manual

Dimplex

Dimplex CAS400LNH-INT User manual

Dimplex

Dimplex EF3003 Quick start guide

Dimplex

Dimplex CDFI1000-PRO User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual