Dimplex SF3202 User manual

PRACTICAL USER’S GUIDE

FOR THE SYMPHONY ENCORE

ELECTRIC FIREPLACE

MODEL NUMBER:

SF3202

Valued Customer,

We are pleased that you have chosen to purchase an electric

fireplace manufactured by Dimplex North America Ltd.

Over the years, valuable memories will occur around the

warmth and comfort of your hearth. Thank you for allowing our

product to be the backdrop for those special moments.

7205410100REV04

Quality checked by:

QUICK REFERENCE GUIDE FOR THE DIMPLEX ELECTRIC

FIREPLACE

1. Prior to the first use of the fireplace verify the following:

• Are the circuit breakers for the socket the unit uses on?

• Are the light bulbs in your fireplace loose? (to check, follow the

instructions for replacing the light bulbs under the maintenance

section of this manual)

2. The heater on your fireplace may emit a slight, harmless odor when

first used. This odor is a normal condition caused by the initial

heating of internal heater parts and will not occur again.

3. The information regarding the model of your fireplace can be found

on the rating plate located under the logset of the unit.

4. If you have any technical questions or concerns regarding the

operation of your fireplace, or require service contact Dimplex North

America customer service at 1-888-DIMPLEX (1-888-346-7539) before

returning the product to the point of purchase.

CONTENTS

PAGE 1 Important Instructions

PAGE 2 Model and Serial Number

Information

PAGE 4 Fireplace Installation

PAGE 4 Operation

PAGE 8 Maintenance

PAGE10 Warranty

IMPORTANT INSTRUCTIONS

SAVE THESE INSTRUCTIONS

PLEASE RETAIN THIS USER’S GUIDE FOR FUTURE REFERENCE

When using electrical appliances, basic precautions should always be followed to reduce the

risk of fire, electric shock, and injury to persons, including the following:

1. Read all instructions before using the electric fireplace.

2. The heater is hot when in use. To avoid burns, do not let bare skin touch hot

surfaces. The trim around the heater outlet becomes hot during heater operation. Keep

combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains

at least 3 feet (0.9m) from the front of the unit.

3. Extreme caution is necessary when any heater is used by or near children or invalids

and whenever the unit is left operating and unattended.

4. Always unplug the electric fireplace when not in use.

5. Do not operate any unit with a damaged cord or plug, or if the heater has malfunctioned,

or if the electric fireplace has been dropped or damaged in any manner. Return heater

to authorized service facility for examination, electrical or mechanical adjustment, or

repair.

6. Do not use outdoors.

7. The electric fireplace is not intended for use in bathrooms, laundry areas and similar

indoor locations. Never locate heater where it may fall into a bathtub or other water

container.

8. Do not run the cord under carpeting. Do not cover cord with throw rugs, runners, or the

like. Arrange cord away from traffic area and where it will not be tripped over.

9. To disconnect the unit, turn the controls off, then remove the plug from the outlet.

10.Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this

may cause an electric shock or fire, or damage to the heater.

11.To prevent a possible fire, do not block air intake or exhaust in any manner. Do not use

on soft surfaces, like a bed, where openings may become blocked.

12.All electrical heaters have hot and arching or sparking parts inside. Do not use in areas

where gasoline, paint, or flammable liquids are used or stored or where the unit will be

exposed to flammable vapors.

13.Do not modify the electric fireplace. Use it only as described in this manual. Any other

use not recommended by the manufacturer may cause fire, electric shock or injury to

persons.

14.Avoid the use of an extension cord. Extension cords may overheat and cause a risk of

fire. If you must use an extension cord, the cord must be No. 16 AWG minimum size

and rated no less than 1875 watts.

15.Do not burn wood or other materials in the electric fireplace.

16.Do not strike the fireplace glass.

17.Always use a certified electrician should new circuits or outlets be required.

18.Always use properly grounded, fused and polarized outlets.

19.Disconnect all power supply before performing any cleaning, maintenance or relocation

of the unit.

20. When transporting or storing the unit and cord, keep in a dry place, free from excessive

vibration and store so as to avoid damage.

NOTE: Procedures and techniques that are considered important enough to emphasize.

CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to

the equipment.

WARNING: Procedures and techniques which, if not carefully followed, will expose the user to

the risk of fire, serious injury, illness or death.

Model Numbe

Serial Number

Model Numbe

Serial Number

IMPORTANT INSTRUCTIONS

If you have any questions about out products please have the product model and serial

numbers available upon calling Dimplex customer service. To locate the model and serial

number labels see below.

Firebox

NOTE

A 15amp, 120 volt circuit is required. A dedicated circuit is preferred but not essential in all

cases. A dedicated circuit will be required if, after installation, the circuit breaker trips or fuse

blows on a regular basis when the heater is operating. Additional appliances on the same

circuit may exceed the current rating of the circuit breaker.

WARNING

Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure

that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire,

electric shock or injury to persons.

Construction and electrical outlet wiring must comply with local building codes and other

applicable regulations to reduce the risk of fire, electric shock and injury to persons.

Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric

shock or injury to persons, always use a licensed electrician.

Model Number

Serial Number

Carton

SITE SELECTION AND PREPARATION

This section provides instructions for selecting a location and preparing the site to install the

fireplace into your Dimplex mantel surround.

NOTE

The fireplace insert comes completely assembled and wired. No tools will be required to

prepare the site and assemble/install the fireplace.

The dimensions of the fireplace insert are 36 ½” wide X 31 ¾” high X 13” deep, the opening

size is 32” wide and 28 ¼” high. This fireplace does not require any venting.

DIMPLEX MANTEL SURROUND

1. Select a suitable location that is not susceptible to moisture and is away from drapes,

furniture and high traffic.

2. For ease of electrical hook up you may wish to locate the fireplace near an existing

outlet. (refer to NOTE 1)

3. Store the fireplace in a safe dry and dust free location.

4. Assemble the fireplace to the mantel surround kit (refer to the mantel assembly

instructions).

WARNING

Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric

shock or injury to persons, always use a licensed electrician.

FIREPLACE INSTALLATION

1. Make sure the units MAIN ON/OFF switch is switched OFF (refer to operating

instruction section).

2. Plug the unit into a 15Amp/120volt outlet. If the cord does not reach, you may use an

extension cord rated for a minimum of 1875 watts.

WARNING

Ensure the power cord is not installed so that it is pinched or against a sharp edge and

ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the

risk of fire, electric shock or injury to persons.

OPERATION

Initializing The Remote Control

1. Turn on the electrical power at the circuit breaker.

2. Slide open the battery cover on the back of the remote transmitter.

3. Install three AAA batteries into the remote control. Replace the battery cover.

Note:

The LCD display will flash when new batteries are inserted.

4. Move the remote transmitter close to the fireplace (less than five feet preferred). Press

any button on the remote control. The remote is transferring the code to the receiver

built into the fireplace.

5. Set the clock by depressing the button marked clock on the transmitter for five seconds.

The hour display will flash.

6. Use the up and down buttons to set the hour.

7. Press the clock button again and the minute display will flash.

8. Use the up and down buttons to set the minute.

9. Press the clock button again and the 0F or 0C display will flash.

10.Use the up and down buttons to select the remote to display temperature in 0F or 0C

11.Press the clock button again. The remote control is now ready for operation.

Remote Control Operation

Warning:

It takes some time for the receiver to respond to the transmitter. Do not press the buttons

more than once within two seconds for correct operation.

Note:

The fireplace has an automatic timer function that will shut your fireplace off if the remote

control has not been operated within a six-hour period.

Auto Mode

Note:

When auto mode is activated the flame and heat will turn on. The heater will turn on and

off to keep the room temperature the same as the remote controls set temperature.

1. Press POWER button to turn unit on. (There may be a slight delay)

2. Press the UP or DOWN buttons to change the set temperature, if desired.

3. In auto mode the remote transmitter will automatically turn on the flame and heater

when the room temperature is below the target temperature and turn off the heater

ONLY when the room temperature is above the target temperature.

4. Press POWER button once to turn unit off.

Timer Mode

1. You can set the timer to the length of time you want the unit to operate

2. (1 to 120 minutes).

3. Press the TIMER button once. The timer display will blink ---

4. Press the UP and DOWN buttons to adjust the timer display in minutes.

5. Press the TIMER button once to set the timer.

6. The timer setting can be reset by pressing the TIMER button and using the DOWN

button until the timer display reads ----, press the TIMER button once to set the timer.

7. Press the POWER button to turn the unit on.

8. The fireplace will automatically shut off when the timer reaches 0 minutes.

Child Proof Function

1. Remove the battery cover on the back of the remote control.

2. Slide the small blue switch down to activate the child proof function.

3. Child Proof will appear on the display screen and all function on the remote will be

locked.

4. To enable normal remote control operation when the child proof function is activated,

press the up and down buttons in the following sequence,

UP-DOWN-DOWN-UP-DOWN the remote functions will now operate normally. The

remote will return to the child proof function if buttons are not pressed after two minutes.

5. To disable the child proof function remove the battery cover on the back of the remote

and slide the small blue switch up.

Batteries

1. The remote control uses 3 AAA size batteries (included). Replace these batteries at

least every 6 months or when the low battery appears on the remote display screen.

2. When batteries are removed wait at least 1 minute before replacing with new batteries.

Code selection

If the current remote control is interfering with the operation of other remote control devices

(TV, VCR, garage doors etc.) The code can be changed on the remote.

To change code:

1. Remove the battery cover on the back of the remote control.

2. Slide the four small switches to any configuration other than the factory set code.

3. Remove the batteries, wait for one minute.

4. Install the batteries.

5. Install the battery cover onto the remote.

6. Reinitialize the remote control.

OPERATION

Electric Fireplace Manual Controls

The manual controls are located inside the fireplace in the upper right hand corner.

A. Manual on/off switch

1. The fireplace has a manual power ON/OFF switch located on the control panel of the

fireplace.

2. To operate press the switch once, to turn the unit on. A red light will illuminate to

indicate the power is on. Press the switch again to turn the unit off.

NOTE:

When the manual power switch is used the heater will run.

The manual ON/OFF switch is to be used only when the remote transmitter is OFF.

B. Flame action control

Turn the flame action control knob to adjust the flame speed control to the desired level.

C. Heater override switch

When the Manual on/off switch is in the on position the heater will run. Turn the heater

override switch to the off position to shut off the heater.

NOTE: Ensure that the heater override switch is in the on position for the heater to work

with the remote control.

RESETTING THE TEMPERATURE CUTOFF SWITCH

Should the heater overheat, an automatic cut out will turn the heater off and it will not come

back on without being reset. It can be reset by switching the MAIN ON/OFF SWITCH to OFF

and waiting 5 minutes before switching the unit back on.

CAUTION

If you need to continuously reset the heater, unplug the unit and call Dimplex North America

Limited at 1-800-668-6663.

MAINTENANCE

WARNING

Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire,

electric shock or damage to persons.

LIGHT BULB REPLACEMENT

Allow at least 5 minutes for light bulbs to cool off before touching bulbs to avoid accidental

burning of skin.

Light bulbs need to be replaced when you notice a dark section of the flame or when the clarity

and detail of the log exterior disappears. There are four bulbs under the log set which

generate the flames and embers and two bulbs above the log that illuminate the log exterior.

LOWER LIGHT BULB REQUIREMENTS

Quantity of 4 clear chandelier or candelabra bulbs with an E-12 (small) socket base, 60 watt

rating.

LOWER LIGHT BULB REPLACEMENT

The lower light bulbs are located at the back of the fireplace under the logset. To access the

lower light bulbs, grasp the back of the plastic emberbed and firmly pull the emberbed forward

and up until the rear tab clears the back ledge. Handle the logset by the under side and place

it out of the way, pull the rotating flicker aside and replace the required bulbs lower light bulbs.

Re-assemble in the reverse order.

CAUTION: Grasping the logset by the logs or the grate when removing the logset may result

in damaging the logset.

Other manuals for SF3202

Table of contents

Other Dimplex Indoor Fireplace manuals

Dimplex

Dimplex DFP6975O User manual

Dimplex

Dimplex 34" Prism User manual

Dimplex

Dimplex Michigan Fire MCN20 User manual

Dimplex

Dimplex VIANA DELUXE VNA20RC User manual

Dimplex

Dimplex LEE User manual

Dimplex

Dimplex Rome User manual

Dimplex

Dimplex OptiFlame Cheriton Deluxe Instruction Manual

Dimplex

Dimplex Mini Mozart Deluxe User manual

Dimplex

Dimplex 6908760100 User manual

Dimplex

Dimplex MILANOef EDS7001F Quick start guide

Dimplex

Dimplex LVA231 User manual

Dimplex

Dimplex BLF50 User manual

Dimplex

Dimplex DFI2309 Quick start guide

Dimplex

Dimplex EWF-SS User manual

Dimplex

Dimplex BLF74 User manual

Dimplex

Dimplex DF1136L User manual

Dimplex

Dimplex OLF46-AM User manual

Dimplex

Dimplex Avola AVA20 User manual

Dimplex

Dimplex BURNHAM BRN20 User manual

Dimplex

Dimplex BF33ST Quick start guide

Dimplex

Dimplex Revillusion 20" User manual

Dimplex

Dimplex CHT20LE User manual

Dimplex

Dimplex RWF-DG User manual

Dimplex

Dimplex Atherton ATH20 Instruction Manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual