Dimplex Dimplex VALENCIA User manual

08/19355/2 Issue 2

VALENCIA

The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility

(EMC) EN55014, EN60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336

‘x’

‘y’

‘z’

639

618

700

655

205

157

617 632

648

550

632

567

668

165 Min.

‘a’

3 4 5

‘a’

‘y’

‘x’

TABLE OF CONTENTS

1. FOREWORD 1

2. INTRODUCTION 1

3. SAFETY PRECAUTIONS 1

4. INSTALLATION 2

4.1 Installation Instructions 2

4.2 Installation Space 2

4.3 Location and Minimum Free Space 2

4.4 Recessed Installation 2

5. OPERATION 2

5.0 Operation 2

5.1 Initializing the remote control 2

5.2 Remote control operation 3

5.3 Manual operation 3

5.4 Thermal safety cut 3

6. CLEANING AND MAINTENANCE 3

6.1 Cleaning 3

6.2 Lamp replacement 3

7. AFTER SALES SERVICE 4

1. FOREWORD

This fire incorporates a flame effect which can be used with or without heating, so that comforting effect may be

enjoyed at any time of the year. The flame effect is provided by a low wattage motor and three 60 watt lamps. Using the

flame effect on its own, therefore, requires little electricity.

The controls are located at the bottom right hand corner of the appliance (see ‘z’ in Fig 1). A choice of 750W or 1500W

heat output is provided by the fan heater, which is concealed at the top of the heater (see ‘x’ in Fig 1) behind the

removable front panel (see ‘y’ in Fig 1).

The Valencia is designed to be inset in a fireplace opening.

2. INTRODUCTION

This instruction manual gives you information about the design, operation and maintenance of your fire, as well as

safety precautions and environmental recommendations.

As you read this manual, you will quickly learn how to operate your fire. You will also find information about the safety

and maintenance of the equipment.

Read the manual carefully before using your fire and then keep the manual in a safe place.

3. SAFETY PRECAUTIONS

•Have the stove installed by a qualified installer in accordance with local and national (fire safety)

regulations.

•Ensure that all packaging items are removed (read any warning labels carefully).

•Retain all packaging until installation is complete.

•The heater must be used on an ~ 230V supply and the voltage marked on the heater must correspond

with the supply voltage.

•Warning: This appliance must be earthed.

•When using electrical appliances, basic precautions should always be followed to reduce the risk of

fire, electrical shock, and injury to persons, including the following:

•If the appliance is damaged, check immediately with the supplier before installation and operation.

•Do not use outdoors,

•Do not use in the immediate surroundings of a bath shower or swimming pool.

•Do not locate the heater immediately below a fixed socket outlet or connection box.

•Do not cover the heater. Do not place material or garments on the heater, or obstruct the air circulation

around the heater, for instance by curtains or furniture, as this could cause overheating and a fire risk.

•Do not leave young children unsupervised in the vicinity of the heater.

•Ensure that furniture, curtains or other combustible material are positioned no closer than 1 meter

from the heater.

•In the event of a fault unplug the heater.

•Although the heater complies with safety standards, we do not recommend its use on deep pile

carpets or on long hair type of rugs.

•The appliance must be positioned so that the plug is accessible.

•If the supply cord is damaged it must be replaced by the manufacturer or service agent or similarly

qualified person in order to avoid a hazard.

- 1 - UK

- 2 - UK

4. INSTALLATION

4.1 INSTALLATION INSTRUCTIONS

Have the stove installed by a qualified installer in conformance with national and local (fire safety) regulations.

Be sure that the chimney functions properly.

4.2 INSTALLATION SPACE (see Fig. 1)

A: Adjustable Feet

B: Recommended built-in height

C: Connection cable

4.3 LOCATION AND MINIMUM FREE SPACE

Before installing read all safety warnings and operating instructions.

At the base of the fire, four adjustable feet (see ‘A’ in Fig. 1) are provided for levelling the fire where the base of the

fireplace opening is raised above the level of the hearth.

Adjust by turning the feet until the desired height has been reached.

The fire is designed to be inset in a fireplace opening - see ‘Recessed Installation’ and Fig. 2 for details.

4.4 RECESSED INSTALLATION

In order to ensure it’s future safety in use, it is essential that this fire is securely fixed to the wall.

IT IS IMPORTANT THAT THE FIXING DEVICE CHOSEN IS APPROPRIATE TO THE WALL MATERIAL TO WHICH

THE FIRE IS BEING FIXED. SOME MODERN INTERNAL BUILDING MATERIALS ARE VERY LOW DENSITY

BLOCK AND REQUIRE SPECIALIZED FIXING DEVICES TO PROVIDE A SAFE,SECURE INSTALLATION.

The installation of this fire should be carried out by a competent person.

Follow steps as outlined below :

1. Make sure that the fire is located on a flat surface.

2. In existing fireplaces seal all draughts and vents to prevent chimney debris from falling onto the fireplace insert.

Do not install into an existing fireplace that is prone to dampness.

3. Remove the fire front panel - see ‘6.2 Lamp Replacement’ and Fig. 7.

4. Locate the 4 fixing holes, position the fire accordingly, and firmly fix the appliance to the wall using the appropriate

screws - see ‘a’ in Fig. 2 for hole fixing dimensions and recommended recess size.

5. Replace the front panel.

If you intend to build a purpose built structure/hearth please use the recommended dimensions as indicated in Fig. 2

If in doubt of any of the above please consult your local builder.

5. OPERATION

5.0 OPERATION

The controls are located at the bottom right hand corner of the appliance - see ‘z’ in Fig. 1.

Connect the fire to your electricity supply.

Note: When either the remote control or the manual controls are used the neon’s will come on for 3 seconds indicating

the appropriate setting - see Fig. 3.

5.1 INITIALIZING THE REMOTE CONTROL

Note: The remote control is packed separately in the carton.

1. Slide open the battery cover on the back of the remote transmitter.

2. Install the AAA batteries into the remote control (see Fig. 4).

3. Replace battery cover.

DISCARD LEAKY BATTERIES

Dispose of batteries in the proper manner according to Provincial and local regulations. Any battery may leak electrolyte

if mixed with a different battery type, if inserted incorrectly, if all the batteries are not replaced at the same time, if

disposed of in a fire or if an attempt is made to charge a battery not intended to be recharged.

- 3 - UK

5.2 REMOTE CONTROL OPERATION

Warning: It takes some time for the receiver to respond to the transmitter. Do not press the buttons more than once

within two seconds for correct operation.

Operation

Setting Operation Indication

Flame effect Press the ‘I’ button once Left Neon

Flame effect & 750W heat setting Press the ‘I’ button again Left & Middle Neon

Flame effect & 1500W heat setting Press the ‘I’ button again All 3 neon’s

To turn off any of the settings press the ‘O’ button once.

To increase or decrease the brightness of the fuel effect use the buttons ( ) as shown in Fig. 5.

5.3 MANUAL OPERATION

Note: The Standby Switch (see ‘a’ in Fig. 6) must be first turned on to operate either the manual or the remote controls.

The red indicator mark on the switch will be visible when it is turned on.

Setting Operation Indication

Flame effect Press the ‘I’ button once Left Neon

Flame effect & 750W heat setting Press the ‘I’ button again Left & Middle Neon

Flame effect & 1500W heat setting Press the ‘I’ button again All 3 neon’s

To turn off any of the settings press the ‘O’ button once.

To increase or decrease the brightness of the fuel effect use the buttons ( ) as shown in Fig. 6.

5.4 THERMAL SAFETY CUT-OUT

For your safety, this appliance has been fitted with thermal cut-out. In the event that the product overheats, the cut-out

switches the heat off automatically.

To bring the heat back into operation, remove the cause of the overheating, then unplug or turn off the electrical supply

to the heater for up to 10 minutes.

When the heater has cooled sufficiently, re-connect and switch on the heater.

6. CLEANING AND MAINTENANCE

Warning: Always disconnect from the power supply before attempting any maintenance.

6.1 CLEANING

Before commencing cleaning, unplug the heater and allow it to cool.

The surface of the heater should be given an occasional wipe over with a soft damp cloth. Do not use detergents

abrasive cleaning powder or polish on the body of the heater. The glass screen should be cleaned carefully with a

chamois leather. Do not use proprietary glass cleaners.

6.2 LAMP REPLACEMENT

To gain access to the lamps.

1. Remove the front frame (see ‘x’ in Fig. 7) by lifting out then up and carefully leave to one side.

2. Remove the three screws (see ‘y’ in Fig. 7) on the fuel effect.

3. Slide the fuel effect out, by holding the front ledge and set aside carefully (taking care not to damage the logs as

they are fragile) – see Fig. 7.

4. For access to the bulbs, carefully rotate the flexible rotisserie out of position ensuring that the rubber grommet is

not lost – see Fig. 8.

5. Unscrew the defective lamp anti-clockwise. Replace with a 230V, 60W E14 SES lamp, do not over tighten (see

Fig. 8).

6. Refit the fuel effect (with three screws) and Front Panel.

Glen Dimplex UK Limited

Millbrook House

Grange Drive

Hedge End

Southampton

Hampshire. SO30 2DF

UK customer help line (8.00AM – 6.00PM Mon-Fri; 8.30AM-1.00PM Sat)

Customer Services: Tel. 0870 7270101

Fax. 0870 7270102

e-mail customer[email protected]

Republic of Ireland Tel. 01 8424833

[c] Glen Dimplex UK Limited

- 4 -

7. After Sales Service

Your product is guaranteed for one year from the date of purchase.

Within this period, we undertake to repair or exchange this product free of charge (excluding lamps & subject to

availability) provided it has been installed and operated in accordance with these instructions.

Your rights under this guarantee are additional to your statutory rights, which in turn are not affected by this guarantee.

Should you require after sales service you should contact our customer services help desk on 0870 727 0101. It would

assist us if you can quote the model number, series, date of purchase, and nature of the fault at the time of your call.

The customer services help desk will also be able to advise you should you need to purchase any spares.

Please do not return a faulty product to us in the first instance as this may result in loss or damage and delay in

providing you with a satisfactory service.

Please retain your receipt as proof of purchase.

Table of contents

Other Dimplex Indoor Fireplace manuals

Dimplex

Dimplex Ignite 60 User manual

Dimplex

Dimplex Revillusion Haydn User manual

Dimplex

Dimplex DFI400R User manual

Dimplex

Dimplex CAS500 User manual

Dimplex

Dimplex SIL48M User manual

Dimplex

Dimplex DF2624L-EU User manual

Dimplex

Dimplex Juneau JUN User manual

Dimplex

Dimplex Revillusion RBF30-FG User manual

Dimplex

Dimplex DWF1203 User manual

Dimplex

Dimplex BLF7451 User manual

Dimplex

Dimplex DF2622 User manual

Dimplex

Dimplex 6908760100 User manual

Dimplex

Dimplex DFP6975O User manual

Dimplex

Dimplex DF2624L-INT User manual

Dimplex

Dimplex 3-STEP Optimyst Instruction Manual

Dimplex

Dimplex Albany Optimyst ABN15-RGB-EU Instruction Manual

Dimplex

Dimplex WYN20 User manual

Dimplex

Dimplex DWF-13XX User manual

Dimplex

Dimplex IN-STUD V1525BT User manual

Dimplex

Dimplex DFR2551G User manual

Dimplex

Dimplex DF2624L User manual

Dimplex

Dimplex SP120SP220 User manual

Dimplex

Dimplex Vivente VVT125 Manual

Dimplex

Dimplex Dakota DKT20 User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual