Dimplex MILANOef EDS7001F Quick start guide

MILANO

MODEL EDS7001F

PARTS & SERVICE MANUAL

TABLE OF CONTENTS

OPERATION PAGE 3

PARTS DRAWING PAGE 5

WIRING SCHEMATICS PAGE 6

PARTS LIST PAGE 7

LIGHT BULB REPLACEMENT PAGE 8

MAIN POWER ON/OFF SWITCH REPLACEMENT PAGE 9

FLAME MOTOR/FLAME ROD REPLACEMENT PAGE 10

HEATER ON/OFF SWITCH PAGE 12

HEATER THERMOSTAT REPLACEMENT PAGE 13

POWER CORD REPLACEMENT PAGE 14

HEATER ASSEMBLY REPLACEMENT PAGE 15

EDS7001F MILANO

NOTE

A 15amp, 120 volt circuit is required. A dedicated circuit is preferred but not

essential in all cases. A dedicated circuit will be required if, after installation, the

circuit breaker trips or fuse blows on a regular basis when the heater is

operating. Additional appliances on the same circuit may exceed the current

rating of the circuit breaker.

WARNING

Ensure the power cord is not installed so that it is pinched or against a sharp

edge and ensure that the power cord is stored or secured to avoid tripping or

snagging to reduce the risk of fire, electric shock or injury to persons.

Construction and electrical outlet wiring must comply with local building codes

and other applicable regulations to reduce the risk of fire, electric shock and

injury to persons.

Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire,

electric shock or injury to persons, always use a licensed electrician.

MILANO

INSTALLATION

1. Make sure the unit is switched OFF (refer to operating instruction section).

2. Plug the unit into a 15Amp/120volt outlet. If the cord does not reach, you

may use an extension cord rated for a minimum of 1875 watts.

OPERATION

To access the controls go to the back of the milano

A. MAIN ON/OFF SWITCH

The on/off switch supplies power to all unit functions (heat/flame)

B. HEATER ON/OFF SWITCH

The HEATER ON/OFF SWITCH supplies power to the heater fan and the

heater element.

C. HEATER THERMOSTAT CONTROL

To adjust the temperature to your individual requirements, turn the thermostat

control clockwise all the way to turn on the heater. When the room reached the

desired temperature, turn the thermostat knob counter clockwise until you hear

a click. Leave in this position to maintain the room temperature at this setting.

For additional heat, turn clockwise until you hear the click again and the heater

will turn on. To turn the heater off, switch the HEATER ON/OFF SWITCH to

the OFF position.

NOTE:- When the heater is switched ON, the heater fan will operate. The heater

element may or may not be on, depending on the thermostat control setting (SEE

“HEATER THERMOSTAT CONTROL”).

back of the milano

EDS7001F MILANO

RESETTING THE TEMPERATURE CUTOFF SWITCH

This unit is equipped with a thermostat that controls the temperature of the room.

It does this by turning the heater on and off. The heater is protected with a safety

device to prevent overheating. Should the heater overheat, an automatic cut out

will turn the heater off and it will not come back on without being reset. To reset

the temperature cutoff switch turn the main power switch to the OFF position and

wait five minutes before switching the unit back on.

OPTIONAL REMOTE CONTROL USAGE

1. Plug the stove into the outlet located on the

side of the receiver.

2. Plug the receiver into the wall outlet.

3. Install a 9 volt battery into the transmitter.

4. Turn the stove main power switch to the on

position prior to using the remote control.

5. The remote control works up to 50 feet away.

6. Push the ON button to turn stove on, push the

OFF button to turn the stove off.

NOTE:

To prevent the risk of fire, the stove plug must be

inserted fully into the receiver.

NOTE:

The remote control and receiver use one of 243

independent frequencies. When replacing the

remote control or the receiver they must be

replaced as a set to ensure proper operation.

The frequency of the remote is located on the

back of the remote on a label. (Figure 1)

Figure 1

EDS7001F MILANO

REPLACEMENT PARTS

MILANO

DIMPLEX

CATALOGUE NO.

EDS7001F

PART NO.

6900840000

MOD. LEVEL

REPLACEMENT PART

1. LOG SET

0438270100RP

2. FRONT DOOR

0438390100RP

3. STOVE TOP

1103740104RP

4. A.C. MOTOR ASSEMBLY

2000140300RP

5. HEATER ASSEMBLY

2000170300RP

6. THERMOSTAT

2300150100RP

7. LOWER LIGHT HARNESS

2500170100RP

8. HEATER ON/OFF SWITCH, MAIN ON/OFF SWITCH

2800070200RP

9. CORDSET

4100040300RP

10. LOWER LIGHT BULBS 60 WATT (2 PER UNIT)

4200020100RP

11. UPPER LIGHT BULBS 7 WATT (1 PER UNIT)

4200020400RP

12. REFLECTOR ROTISSERIE

5900080600RP

13. FRONT DOOR GLASS

5900200100RP

14. MIRROR

5900210100RP

15. THERMOSTAT KNOB

8800000300RP

16. FRONT DOOR KNOB

8800320100RP

EDS7001F MILANO

If unit was operating prior to servicing allow at least 10 minutes for light bulbs and

heating element to cool off to avoid accidental burning of skin.

Disconnect power before attempting any maintenance or cleaning to reduce the

risk of electric shock or damage to persons.

Light bulbs need to be replaced when you notice a dark section of the flame or

when the clarity and detail of the log exterior disappears. There is one bulb at

the top of the opening that illuminates the log set exterior and two bulbs under

the log set which generate the flames and embers.

It is a good idea to replace all of the light bulbs at one time if they are close to the

end of their rated life. Group replacement will reduce the number of times you

need to open the unit to replace the light bulbs.

TO REPLACE THE UPPER LIGHT BULB

1. Unscrew the two black knobs on the front of the unit by turning

counterclockwise.

2. Grasp onto the front door, gently lift up and pull the door off of the unit.

3. Unscrew the bulb counter clockwise.

4. Insert new bulb.

5. Install the front door over the rods, gently lifting up to engage the door into the

slot in the roof.

6. Screw the two black knobs clockwise until tightened.

TO REPLACE THE LOWER LIGHT BULBS

1. Unscrew the two black knobs on the front of the unit by turning

counterclockwise.

2. Grasp onto the front door, gently lift up and pull the door off of the unit.

3. Remove the screw from the logset located in the center of the emberbed and

remove the logset from the unit.

4. Locate and examine the bulbs to determine which bulb(s) required

replacement.

5. Unscrew the bulb(s) counter clockwise.

6. Insert new bulb(s).

7. Install the logset into the unit, pushing firmly against the glass. Replace the

logset retaining screw into the ember bed.

8. Install the front door over the threaded rods, gently lifting up to engage the door

into the slot in the roof.

9. Screw the two black knobs clockwise until tightened.

LOWER LIGHT BULB REQUIREMENTS

Quantity of 2 clear chandelier or candelabra bulbs with an E-12 (small) socket

base, 60 watt rating. Example GE 60BC of Philips 60 CTC.

Do not exceed 60 watts.

UPPER LIGHT BULB REQUIREMENTS

Quantity of 1 clear chandelier or candelabra bulbs with an E-12 (small) socket

base, 7 watt rating. Do not exceed 7 watts.

EDS7001F MILANO

If the stove was operating prior to servicing allow at least 10 minutes for light

bulbs and heating element to cool off to avoid accidental burning of skin.

Disconnect power before attempting any maintenance or cleaning to reduce the

risk of electric shock or damage to persons.

TO REPLACE MAIN ON/OFF SWITCH

1. Remove the stove pipe kit (if equipped).

2. Unscrew the two black knobs on the front of the unit by turning

counterclockwise.

3. Grasp onto the front door, gently lift up and pull the door off of the unit.

4. Remove the upper light bracket mounting screws from the top and remove

the light bracket assembly from the unit.

5. Locate the four cam locks on the side panels inside the upper corners of

the stove and turn with a large slot screwdriver so the triangle on the cam

lock is pointing up towards the top of the stove.

6. Grasp the top at both sides and gently pull to release the top.

7. Locate the main on/off switch mounted on the rear panel and disconnect

the wiring clips and connections noting their original locations.

8. Depress the retainer clips on the rear of the switch and push the switch

out of the rear cover.

9. Properly orientate the new switch and connect all of the wiring clips and

connections.

10.Reassemble in the reverse order as above.

EDS7001F MILANO

If the stove was operating prior to servicing allow at least 10 minutes for light

bulbs and heating element to cool off to avoid accidental burning of skin.

Disconnect power before attempting any maintenance or cleaning to reduce the

risk of electric shock or damage to persons.

TO REPLACE FLAME MOTOR/FLAME ROD

1. Do to the partial disassembly of the stove care must be taken not to

scratch any surfaces or damage any components during the repair.

2. Remove the stove pipe kit (if equipped).

3. Unscrew the two black knobs on the front of the unit by turning

counterclockwise.

4. Grasp onto the front door, gently lift up and pull the door off of the unit.

5. Remove the upper light bracket mounting screws from the top and remove

the light bracket assembly from the unit.

6. Locate the four cam locks on the side panels inside the upper corners of

the stove and turn with a large slot screwdriver so the triangle on the cam

lock is pointing up towards the top of the stove.

7. Grasp the top at both sides and gently pull to release the top.

8. Locate and remove the mirror by pulling it out of the slots being careful not

to bump or drop it.

9. Locate the flame motor and flame rod assembly, remove the motor

mounting screws with a short handled screw driver.

10.Remove the four screws from the rear panel.

11.Locate the main on/off switch mounted on the rear panel and disconnect

the wiring connections noting their original locations.

12.Slide the rear panel up approximately three inches, locate and disconnect

the wiring for the motor.

13.Remove the mounting bracket screws and pull the flame motor and flame

rod assembly out of the mounting bracket.

NOTE: When removing the flame motor some damage may occur to the

flame rod. If flame rod is damaged replace to insure proper operation.

Other manuals for MILANOef EDS7001F

Table of contents

Other Dimplex Indoor Fireplace manuals

Dimplex

Dimplex EF3003 User manual

Dimplex

Dimplex BLF74 User manual

Dimplex

Dimplex EF3003-230 User manual

Dimplex

Dimplex Brayford BFD20E Instruction Manual

Dimplex

Dimplex Optiflame 3D Braemar BMR20 Instruction Manual

Dimplex

Dimplex DFB6016 Quick start guide

Dimplex

Dimplex CAS400LNH-INT User manual

Dimplex

Dimplex SAHARA SHR12 User manual

Dimplex

Dimplex ENG56 User manual

Dimplex

Dimplex DCF44GS User manual

Dimplex

Dimplex DCF7850 User manual

Dimplex

Dimplex BF36 Series User manual

Dimplex

Dimplex TANGO TNG20 User manual

Dimplex

Dimplex Siena Fire SNA20 User manual

Dimplex

Dimplex Adagio User manual

Dimplex

Dimplex DWF120330B User manual

Dimplex

Dimplex DFOP25 User manual

Dimplex

Dimplex COMPACT FIREPLACE User manual

Dimplex

Dimplex BLF34 User manual

Dimplex

Dimplex PRISM BLF3451-AU User manual

Dimplex

Dimplex 5011139048455 User manual

Dimplex

Dimplex NARVIK NOVA User manual

Dimplex

Dimplex PF2325 User manual

Dimplex

Dimplex TFA36E User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual