Desa EFS26NRA Quick start guide

Save this manual for future reference.

For more information, visit www.desatech.com

WARNING: If the information in this manual is not

followedexactly,afireorexplosionmayresultcausing

property damage, personal injury, or loss of life.

— Do not store or use gasoline or other flammable

vaporsandliquidsinthevicinityofthisoranyother

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediatelycallyourgassupplierfromaneighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire

department.

— Installationandservicemustbeperformedbyaquali-

fied installer, service agency, or the gas supplier.

UNVENTED (VENT-FREE) GAS

COMPACT CLASSIC HEARTH® FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

REMOTE-READY MODELS:

VMH26PRB, VMH26NRB, EFS26NRA, EFS26PRA

Shown with optional cabinet mantel/hearth base accessory.

www.desatech.com 113110-01A

WARNING: Improper installation, adjustment, altera-

tion, service, or maintenance can cause injury or prop-

ertydamage.Refertothismanualforcorrectinstallation

and operational procedures. For assistance or addi-

tional information consult a qualified installer, service

agency, or the gas supplier.

WARNING: This is an unvented gas-fired heater. It uses

air (oxygen) from the room in which it is installed.

Provisions for adequate combustion and ventilation air

must be provided. Refer to Air for Combustion and

Ventilation section on page 6 of this manual.

This appliance may be installed in an aftermarket,*

permanently located, manufactured (mobile) home,

where not prohibited by local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the

manufacturer

TABLE OF CONTENTS

Safety Information ............................................... 3

Product Identification .......................................... 4

Optional Remote Control Accessories ................ 5

Local Codes ........................................................ 5

Product Features ................................................ 5

Unpacking ........................................................... 5

Assembly ............................................................ 5

Air For Combustion and Ventilation .................... 6

Installation ........................................................... 9

Operating Fireplace .......................................... 22

Inspecting Burners ............................................ 25

Cleaning and Maintenance ............................... 26

Wiring Diagram ................................................. 27

Troubleshooting ................................................ 28

Specifications .................................................... 32

Replacement Parts ........................................... 33

Service Hints ..................................................... 33

Technical Service .............................................. 33

Illustrated Parts Breakdown and Parts List ....... 34

Accessories....................................................... 36

Warranty Information.......................... Back Cover

www.desatech.com

113110-01A 3

SAFETY INFORMATION

WARNING:Thisproductcon-

tains and/or generates chemi-

cals known to the State of Cali-

fornia to cause cancer or birth

defects, or other reproductive

harm.

IMPORTANT:Readthisowner’s

manualcarefullyandcompletely

beforetryingtoassemble,oper-

ate,or servicethisfireplace. Im-

proper use of this fireplace can

cause serious injury or death

fromburns,fire,explosion,elec-

trical shock, and carbon mon-

oxide poisoning.

DANGER:Carbonmonoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs of car-

bonmonoxidepoisoningresembletheflu,withhead-

aches, dizziness, or nausea. If you have these signs,

thefireplace may notbeworkingproperly.Getfresh

air at once! Have fireplace serviced. Some people

are more affected by carbon monoxide than others.

These include pregnant women, people with heart

orlung disease or anemia, those under theinfluence

of alcohol, and those at high altitudes.

Naturaland Propane/LPGas: Naturalandpropane/

LP gases are odorless. An odor-making agent is

added to the gas. The odor helps you detect a gas

leak. However, the odor added to the gas can fade.

Gas may be present even though no odor exists.

Make certain you read and understand all warn-

ings. Keep this manual for reference. It is your

guideto safeand proper operation of this fireplace.

WARNING: Any change to

this fireplace or its controls can

be dangerous.

WARNING: Do not use a

blowerinsert,heatexchangerin-

sert, or other accessory not ap-

provedforusewiththisfireplace.

WARNING:Donotallowfans

toblowdirectlyintothefireplace.

Avoidanydraftsthatalterburner

flame patterns. Ceiling fans can

create drafts that alter burner

flame patterns. Altered burner

patterns can cause sooting.

Due to high temperatures, the

applianceshouldbelocatedout

of traffic and away from furni-

ture and draperies.

Do not place clothing or other

flammable material on or near

the appliance. Never place any

objects on the heater.

Fireplace front and screen be-

come very hot when running

heater.Keepchildrenandadults

awayfromhotsurfacestoavoid

burns or clothing ignition. Fire-

place will remain hot for a time

after shutdown. Allow surfaces

to cool before touching.

Carefully supervise young chil-

dren when they are in the room

with fireplace. When using the

hand-held remote accessory

keep selector switch in the OFF

positiontopreventchildrenfrom

turningon burnerswithremote.

You must operate this fireplace

withthefireplacescreeninplace.

Make sure fireplace screen is

closedbeforerunningfireplace.

Keep the appliance area clear

and free from combustible ma-

terials,gasoline,andotherflam-

mable vapors and liquids.

www.desatech.com 113110-01A

1. This appliance is only for use with the type of

gas indicated on the rating plate. This appli-

ance is not convertible for use with other

gases.

2. Do not place propane/LP supply tank(s) in-

side any structure. Locate propane/LP supply

tank(s) outdoors.

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not

use any phone in your building

• immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions

• if you cannot reach your gas supplier, call

the fire department

4. This fireplace shall not be installed in a bath-

room or bedroom.

5. Do not use this fireplace as a wood-burning

fireplace. Use only the logs provided with the

fireplace.

6. Do not add extra logs or ornaments such as

pine cones, vermiculite, or rock wool. Using

these added items can cause sooting. Do not

add lava rock around base. Rock and debris

could fall into the control area of fireplace.

7. This fireplace is designed to be smokeless. If

logs ever appear to smoke, turn off fireplace

andcall a qualified service person.

Note:

Dur-

ing initial operation, slight smoking could oc-

cur due to log curing and fireplace burning

manufacturing residues.

8. To prevent the creation of soot, follow the

instructions in Cleaning and Maintenance,

page 26.

9. Before using furniture polish, wax, carpet

cleaner, or similar products, turn fireplace off.

If heated, the vapors from these products may

create a white powder residue within burner

box or on adjacent walls or furniture.

10. This fireplace needs fresh air ventilation to

run properly. This fireplace has an Oxygen

Depletion Sensing (ODS) safety shutoff sys-

tem. The ODS shuts down the fireplace if not

enough fresh air is available. See Air for Com-

bustion and Ventilation, pages 6 through 8. If

fireplacekeeps shutting off,seeTroubleshoot-

ing, pages 28 through 31.

11. Do not run fireplace

• where flammable liquids or vapors are used

or stored.

• under dusty conditions.

12. Do not use this fireplace to cook food or burn

paper or other objects.

13. Never place any objects in the fireplace or

on logs.

14. Do not use fireplace if any part has been under

water.Immediatelycallaqualifiedservicetech-

nician to inspect the room fireplace and to re-

place any part of the control system and any

gas control which has been under water.

15. Turn off and unplug fireplace and let cool be-

fore servicing. Only a qualified service per-

son should service and repair fireplace.

16. Operating fireplace above elevations of 4,500

feet could cause pilot outage.

17. Do not operate fireplace if any log is broken.

Do not operate fireplace if a log is chipped

(dime-sized or larger).

18. Topreventperformanceproblems,donotusepro-

pane/LPfuel tank of less than 100 lbs. capacity.

19. Provide adequate clearances around air

openings.

SAFETY INFORMATION

Continued

PRODUCT

IDENTIFICATION

Figure 1 - Vent-Free Compact Classic

Hearth

Fireplace

OFF

REMOTE

Screen

Fireplace

Cabinet

Logs

Ignitor

Button

Remote

Control

(Optional)

Selector

Switch

(Optional) Control

Knob

www.desatech.com

113110-01A 5

OPTIONAL REMOTE

CONTROL ACCESSORIES

There are four optional remote controls that can

be purchased separately:

• wall switch

• hand-held ON/OFF remote

• wall thermostat

• hand-held thermostat remote

See Accessories, pages 36 and 37.

LOCAL CODES

Install and use fireplace with care. Follow all lo-

cal codes. In the absence of local codes, use the

latest edition of TheNational Fuel Gas CodeANSI

Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

PRODUCT FEATURES

SAFETY PILOT

This fireplace has a pilot with an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The

ODS/pilot is a required feature for vent-free room

fireplaces. The ODS/pilot shuts off the fireplace

if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This fireplace has a piezo ignitor. This system re-

quires no matches, batteries, or other sources to

light fireplace.

UNPACKING

1. Remove fireplace and hood from carton. Log

is wrapped and inside fireplace. Do not re-

move at this time.

2. Remove all protective packaging applied to

fireplace for shipment.

3. Make sure your fireplace includes one hard-

ware packet.

4. Check fireplace for any shipping damage. If

fireplace is damaged, promptly inform dealer

where you bought fireplace.

ASSEMBLY

WARNING: Always have

branch support and screen in

placebeforeoperatingfireplace.

This prevents excessive tem-

peraturesonfireplacesurfaces.

WARNING: Failure to posi-

tion the parts in accordance

with these diagrams or failure

to use only parts specifically

approved with this fireplace

may result in property damage

or personal injury.

ASSEMBLING FIREPLACE

Tools Required:

• Phillips screwdriver

• 5/16" hex wrench

• slotted screwdriver

• scissors

1. Remove two screws that hold fireplace screen

in place for shipping. These screws are located

neartop of screen. Discardscrews.Liftfireplace

screenupandpullouttoremove.Setscreenaside

until installation has been completed.

2. Cut two plastic straps to remove the log from

the firebox cavity.

3. An optional blower is available. See Acces-

sories, pages 36and 37. Installoptional blower

now. Follow installation instructions provided

with blower or (see page 14).

Figure 2 - Removing Screen

Screen

Burner Support

With Log

Locator Tabs

Branch

Support

Shoulder

Screw

www.desatech.com 113110-01A

4. Locate four black phillips sheet metal screws

from the hardware packet.

5. Rotate hood as shown in Figure 3. Make sure

hood tabs point toward fireplace.

6. Insert hood tabs between baffle and louvers

(see Figure 3).

7. Gently rotate hood to upright position. Make

sure hood tabs are behind louvers and hood is

resting on firebox top (see Figure 3).

8. Align screw holes on hood with screw holes

on firebox top.

9. Insert screws as shown in Figure 3. Tighten

screws firmly.

ASSEMBLY

Continued

Figure 3 - Assembling Hood

Hood Tab

Sheet Metal

Screws

Louver

Baffle

Firebox Top

Hood

Hood Tabs

AIR FOR COMBUSTION

AND VENTILATION

WARNING: This fireplace

shall not be installed in a con-

fined space or unusually tight

construction unless provisions

are provided for adequate com-

bustionandventilationair.Read

the following instructions to in-

sureproperfreshairforthisand

otherfuel-burningappliancesin

your home.

Today’s homes are built more energy efficient than

ever. New materials, increased insulation, and new

construction methods help reduce heat loss in

homes. Home owners weather strip and caulk

around windows and doors to keep the cold air out

and the warm air in. During heating months, home

owners want their homes as airtight as possible.

While it is good to make your home energy effi-

cient, your home needs to breathe. Fresh air must

enter your home.All fuel-burning appliances need

fresh air for proper combustion and ventilation.

Exhaust fans, fireplaces, clothes dryers, and fuel

burning appliances draw air from the house to

operate. You must provide adequate fresh air for

these appliances. This will insure proper venting

of vented fuel-burning appliances.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Section 5.3,Air

for Combustion and Ventilation.

All spaces in homes fall into one of the three fol-

lowing ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space

The information on pages 6 through 8 will help you

classifyyour space andprovideadequateventilation.

Unusually Tight Construction

The air that leaks around doors and windows may

provide enough fresh air for combustion and ven-

tilation. However, in buildings of unusually tight

construction,you must provide additional fresh air.

www.desatech.com

113110-01A 7

Unusually tight construction is defined as

construction where:

a. walls and ceilings exposed to the out-

side atmosphere have a continuous

water vapor retarder with a rating of

one perm (6 x 10-11 kg per pa-sec-m2)

or less with openings gasketed or

sealed

and

b. weather stripping has been added on

openable windows and doors

and

c. caulking or sealants are applied to ar-

eas such as joints around window and

door frames, between sole plates and

floors, between wall-ceiling joints, be-

tween wall panels, at penetrations for

plumbing, electrical, and gas lines, and

at other openings.

If your home meets all of these three crite-

ria, you must provide additional fresh air.

See

Ventilation Air From Outdoors

, page 8

If your home does not meet all of the three

criteriaabove,proceedto

DeterminingFresh-

Air Flow For Fireplace Location,

below.

Confined and Unconfined Space

The National Fuel Gas Code,ANSI Z223.1/NFPA

54 defines a confined space as a space whose vol-

ume is less than 50 cubic feet per 1,000 Btu per

hour (4.8 m3per kw) of the aggregate input rating

of all appliances installed in that space and an un-

confined space as a space whose volume is not

less than 50 cubic feet per 1,000 Btu per hour (4.8

m3per kw) of the aggregate input rating of all ap-

pliances installed in that space. Rooms communi-

cating directly with the space in which the appli-

ances are installed*, through openings not fur-

nished with doors, are considered a part of the

unconfined space.

*Adjoiningroomsare communicating only if there

are doorless passageways or ventilation grills be-

tween them.

AIR FOR COMBUSTION

AND VENTILATION

Continued

DETERMINING FRESH-AIR FLOW

FOR FIREPLACE LOCATION

Determining if You Have a Confined or

Unconfined Space

Use this work sheet to determine if you have a

confined or unconfined space.

Space: Includes the room in which you will in-

stall fireplace plus any adjoining rooms with

doorlesspassageways or ventilation grills between

the rooms.

1. Determine the volume of the space (length x

width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example:

Space size 16 ft. (length) x 14 ft.

(width) x 8 ft. (ceiling height) = 1792 cu. ft. (vol-

ume of space)

If additional ventilation to adjoining room is sup-

plied with grills or openings, add the volume of

these rooms to the total volume of the space.

2. Multiply the space volume by 20 to determine

the maximum Btu/Hr the space can support.

__________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example:

1792 cu. ft. (volume of space) x 20 =

35,840 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in

the space.

Vent-free fireplace _________ Btu/Hr

Gas water heater* _________ Btu/Hr

Gas furnace _________ Btu/Hr

Vented gas heater _________ Btu/Hr

Gas fireplace logs _________ Btu/Hr

Other gas appliances* + ________ Btu/Hr

Total = ________ Btu/Hr

* Do not include direct-vent gas appliances. Di-

rect-ventdrawscombustion air from the outdoors

and vents to the outdoors.

Example:

Gas water heater _____________ Btu/Hr

Vent-free fireplace _____________ Btu/Hr

Total _____________ Btu/Hr

4. Compare the maximum Btu/Hr the space can

support with the actual amount of Btu/Hr used.

________

Btu/Hr(maximumthespacecansupport)

________

Btu/Hr(actual amount of Btu/Hr used)

Example:

35,840 Btu/Hr (maximum the space

can support)

40,000 Btu/Hr (actual amount of

Btu/Hr used)

30,000

10,000

40,000

www.desatech.com 113110-01A

Thespace in the above exampleis aconfined space

because the actual Btu/Hr used is more than the

maximum Btu/Hr the space can support.You must

provide additional fresh air. Your options are as

follows:

A. Rework worksheet, adding the space of an ad-

joining room. If the extra space provides an

unconfined space, remove door to adjoining

room or add ventilation grills between rooms.

See Ventilation Air From Inside Building.

B. Vent room directly to the outdoors. See Venti-

lation Air From Outdoors.

C. Install a lower Btu/Hr fireplace, if lower Btu/Hr

size makes room unconfined.

If the actual Btu/Hr used is less than the maxi-

mum Btu/Hr the space can support, the space is

an unconfined space. You will need no additional

fresh air ventilation.

WARNING: If the area in

which the fireplace may be op-

erated is smaller than that de-

finedasanunconfinedspaceor

if the building is of unusually

tight construction, provide ad-

equate combustion and ventila-

tion air by one of the methods

described in the

National Fuel

Gas Code, ANSI Z223.1/NFPA

54 Section 5.3

or applicable lo-

cal codes

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining un-

confined space. When ventilating to an adjoining

unconfined space, you must provide two perma-

nent openings: one within 12" of the ceiling and

one within 12" of the floor on the wall connecting

the two spaces (see options 1 and 2, Figure 4).

You can also remove door into adjoining room (see

option 3, Figure 4). Follow the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for

Combustion and Ventilation for required size of

ventilation grills or ducts.

AIR FOR COMBUSTION

AND VENTILATION

Continued

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills

or ducts. You must provide two permanent open-

ings: one within 12" of the ceiling and one within

12" of the floor. Connect these items directly to

the outdoors or spaces open to the outdoors. These

spaces include attics and crawl spaces. Follow the

National Fuel Gas Code, ANSI Z223.1/NFPA 54,

Section 5.3, Air for Combustion and Ventilation

for required size of ventilation grills or ducts.

IMPORTANT:

Do not provide openings for inlet

or outlet air into attic if attic has a thermostat-con-

trolled power vent. Heated air entering the attic

will activate the power vent.

Figure 4 - Ventilation Air from Inside

Building

Remove

Door into

Adjoining

Room,

Option 3

Ventilation Grills

Into Adjoining Room,

Option 2

12"

Ventilation

Grills

into Adjoining

Room,

Option 1

Figure 5 - Ventilation Air from Outdoors

Outlet

Air Ventilated

Attic

Outlet

Air

Inlet

Air

Inlet Air Ventilated

Crawl Space

Crawl

Space

To Attic

www.desatech.com

113110-01A 9

INSTALLATION

NOTICE:Thisheaterisintended

for use as supplemental heat.

Use this heater along with your

primary heating system. Do not

install this heater as your pri-

mary heat source. If you have a

centralheatingsystem,youmay

run system’s circulating blower

whileusingheater.Thiswillhelp

circulatetheheatthroughoutthe

house. In the event of a power

outage, you can use this heater

as your primary heat source.

WARNING: A qualified ser-

vice person must install fire-

place. Follow all local codes.

WARNING: Never install the

fireplace

• in a bathroom or bedroom

• in a recreational vehicle

• where curtains, furniture,

clothing, or other flammable

objectsarelessthan36inches

from the front, top, or sides of

the fireplace

• as a fireplace insert

• in high traffic areas

• in windy or drafty areas

CAUTION:Thisfireplacecre-

ates warm air currents. These

currents move heat to wall sur-

faces next to fireplace. Install-

ingfireplacenexttovinylorcloth

wallcoveringsoroperatingfire-

placewhereimpurities(suchas,

but not limited to, tobacco

smoke,aromaticcandles,clean-

ingfluids,oilorkerosenelamps,

etc.) in the air exist, may dis-

color walls or cause odors.

IMPORTANT:

Vent-free fireplaces add moisture to

theair.Althoughthisisbeneficial,installing fireplace

in rooms without enough ventilation air may cause

mildewtoformfromtoo much moisture. See Airfor

Combustion and Ventilation, pages 6 through 8.

Note:

Your fireplace is designed to be used in zero

clearance installations. Wall or framing material can

be placed directly against any exterior surface on the

rear,sides,ortopofyourfireplace,exceptwherestand-

offspacersareintegrally attached. If standoffspacers

are attached to your fireplace, these spacers can be

placed directly against wall or framing materials.

Note:

When installing fireplace directly on car-

peting, tile or other combustible material, other

than wood flooring, the fireplace shall be installed

on a metal or wood panel extending the full width

and depth of the fireplace.

Use the dimensions shown for rough openings to

create the easiest installation (see Built-In Fire-

place Installation, page 10).

CHECK GAS TYPE

Use the correct gas type (natural or propane/LP)

for your unit. If your gas supply is not correct, do

not install fireplace. Call dealer where you bought

fireplace for proper type fireplace.

WARNING: This appliance

is equipped for (natural or pro-

pane/LP) gas. Field conversion

is not permitted.

INSTALLATION ITEMS

Before installing fireplace, make sure you have

the items listed below.

• external regulator (supplied by installer, for

propane/LP units only)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• test gauge connection*

• ground joint union

• sediment trap

• tee joint

• pipe wrench

* ACSAdesign-certified equipment shutoff valve

with 1/8" NPT tap is an acceptable alternative to

test gauge connection. Purchase the optional CSA

design-certifiedequipment shutoffvalve from your

dealer. See Accessories, pages 36 and 37.

Note:

If desired, purchase a four-sided trim kit

for built-in installations. See Accessories,

pages 36 and 37.

www.desatech.com 113110-01A

MINIMUM CLEARANCE TO

COMBUSTIBLE MATERIALS

Top Left and Bottom

Right Sides and Rear

36" 6" 0"

FIREPLACE CLEARANCES

WARNING: Maintain the

minimum clearances shown in

Figure 6. If you can, provide

greater clearances from floor,

ceiling, and joining wall.

If your fireplace is to be used with an optional

mantel, the installation instructions included with

your mantel shows an CSA approved method of

attaching the fireplace/mantel system to a wall.

IMPORTANT:

Only use optional cabinet or cor-

ner mantels specified in this manual. Purchase the

optional mantel from your dealer (see Accesso-

ries, pages 36 and 37).

If your fireplace is to be recessed into the wall,

see Built-In Fireplace Installation to secure your

fireplace into the wall.

CAUTION: If you install the

fireplace in a home garage

• fireplacepilotandburnermust

be at least 18 inches above

floor.

• locatefireplacewheremoving

vehicle will not hit it.

For convenience and efficiency, install fireplace

• wherethere iseasy accessfor operation, inspec-

tion, and service

• in coldest part of room

An optional blower kit is available from your

dealer. See Accessories, pages 36 and 37. If plan-

ning to use blower, follow instructions provided

with blower for power source.

INSTALLATION

Continued

Minimum Clearances For Side

Combustible Material, Side Wall, and

Ceiling

A. Clearances from the side of the fireplace cabi-

net to any combustible material and wall

should follow diagram in Figure 6.

Example: The face of a mantel, bookshelf,

etc. is made of combustible material and pro-

trudes 3 1/2" from the wall. This combustible

material must be 4" from the side of the fire-

place opening (see Figure 6).

B. Clearances from the top of the fireplace

opening to the ceiling should not be less than

36 inches.

C. For mantel clearances, see Figure 10 on

page 12.

Figure 6 - Minimum Clearance for

Combustible to Wall

*Minimum 16 inches from Side Wall

Example

Actual Framing

Height 26" 26 7/8"

Front Width 26 3/4" 26 7/8"

Depth 9 1/2" 10 1/2"

Bottom 3/4" 3/4"

1. Frameinroughopening.Use dimensionsshown

in Figure 7, page 11 for the rough opening. If

installing in a corner, use dimensions shown in

Figure 8 for the rough opening. The height is

26 7/8" which is the same as the wall opening

above.

BUILT-IN FIREPLACE

INSTALLATION

Built-in installation of this fireplace involves in-

stalling fireplace into a framed-in enclosure. This

makes the front of fireplace flush with wall. An

optional trim kit accessory is available (see Ac-

cessories, pages 36 and 37). Trim will extend past

sidesof fireplaceapproximately 1/2inch. This will

cover the rough edges of the wall opening. If in-

stalling a built-in mantel above the fireplace, you

must follow the clearances shown in Figure 10,

page 12. Follow the instructions below to install

the fireplace in this manner.

This manual suits for next models

Table of contents

Other Desa Indoor Fireplace manuals

Desa

Desa V50S Quick start guide

Desa

Desa Variable Manually-Controlled Models Quick start guide

Desa

Desa VC36 Quick start guide

Desa

Desa K42EN Series Quick start guide

Desa

Desa SDVBNC Quick start guide

Desa

Desa VMH10TPB Specification sheet

Desa

Desa EFS33NRB Quick start guide

Desa

Desa VFF-32S-AKA Quick start guide

Desa

Desa CHDV42NR-B Quick start guide

Desa

Desa CGMFN Quick start guide

Desa

Desa C36EMW User manual

Desa

Desa VVF36 Quick start guide

Desa

Desa VM42 Quick start guide

Desa

Desa VTGF33PRA Quick start guide

Desa

Desa VK36N SERIES Quick start guide

Desa

Desa IRONHAUS Yellowstone IDVF36SP Quick start guide

Desa

Desa VVC36PE Series Quick start guide

Desa

Desa (V)GM36 Quick start guide

Desa

Desa E32, VE36, VE32 User manual

Desa

Desa VTGF33NRB Quick start guide

Desa

Desa TC36N Series Quick start guide

Desa

Desa VTGF33NRA Quick start guide

Desa

Desa EFS33NR Quick start guide

Desa

Desa Comfort Glow CGCF26NR Quick start guide

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Miles Industries

Miles Industries Vogue 1300IRN Installation & operating instructions