Desa VDCFRNA Quick start guide

UNVENTED (VENT-FREE) GAS COMPACT CLASSIC HEARTH®

DUAL BURNER FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

Save this manual for future reference.

For more information, visit www.desatech.com

THERMOSTAT MODELS

VDCFTNA AND VDCFTPA

REMOTE-READY MODELS

VDCFRPA AND VDCFRNA

Shown with Optional Cabinet Mantel/Hearth Base Accessory

WARNING: If the information in this manual is not fol-

lowed exactly, a ﬁre or explosion may result causing

property damage, personal injury or loss of life.

— Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁre

department.

— Installation and service must be performed by a quali-

ﬁed installer, service agency or the gas supplier.

www.desatech.com 113133-01B

WARNING: Improper installation, adjustment, altera-

tion, service or maintenance can cause injury or prop-

erty damage. Refer to this manual for correct installation

and operational procedures. For assistance or addi-

tional information consult a qualiﬁed installer, service

agency or the gas supplier.

WARNING: This is an unvented gas-ﬁred heater. It uses

air (oxygen) from the room in which it is installed. Provi-

sions for adequate combustion and ventilation air must

be provided. Refer to Air for Combustion and Ventilation

section on page 6 of this manual.

This appliance may be installed in an aftermarket,* per-

manently located, manufactured (mobile) home, where

not prohibited by local codes.

This appliance is only for use with the type of gas indi-

cated on the rating plate. This appliance is not convert-

ible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

TABLE OF CONTENTS

Safety Information ............................................... 3

Product Identiﬁcation ........................................... 5

Optional Remote Control Accessories ................. 5

Local Codes ........................................................ 5

Product Features ................................................. 5

Unpacking ........................................................... 5

Hood Assembly ................................................... 6

Air for Combustion and Ventilation ...................... 6

Installation ........................................................... 9

Operating Fireplace ........................................... 21

Inspecting Burners ............................................ 27

Cleaning and Maintenance ................................ 27

Wiring Diagram .................................................. 28

Troubleshooting ................................................. 29

Speciﬁcations .................................................... 33

Illustrated Parts Breakdown and Parts List ....... 34

Accessories ....................................................... 40

Replacement Parts ............................................ 42

Service Hints ..................................................... 42

Technical Service .............................................. 42

Warranty Information ...........................Back Cover

State of Massachusetts: The installation must be made by a licensed plumber or gas ﬁtter in the

Commonwealth of Massachusetts.

Sellers of unvented propane or natural gas-ﬁred supplemental room heaters shall provide to each

purchaser a copy of 527 CMR 30 upon sale of the unit.

Vent-free gas products are prohibited for bedroom and bathroom installation in the Common-

wealth of Massachusetts.

www.desatech.com

113133-01B 3

SAFETY INFORMATION

WARNING: This product con-

tains and/or generates chemicals

known to the State of California

to cause cancer or birth defects

or other reproductive harm.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble, op-

erate or service this ﬁreplace.

Improper use of this ﬁreplace

can cause serious injury or

death from burns, ﬁre, explo-

sion, electrical shock and carbon

monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs of carbon

monoxide poisoning resemble the ﬂu, with head-

aches, dizziness or nausea. If you have these signs,

the ﬁreplace may not be working properly. Get

fresh air at once! Have ﬁreplace serviced. Some

people are more affected by carbon monoxide than

others. These include pregnant women, people with

heart or lung disease or anemia, those under the

inﬂuence of alcohol and those at high altitudes.

Natural and Propane/LP Gas: Natural and pro-

pane/LP gases are odorless. An odor-making agent

is added to the gas. The odor helps you detect a gas

leak. However, the odor added to the gas can fade.

Gas may be present even though no odor exists.

Make certain you read and understand all warnings.

Keep this manual for reference. It is your guide to

safe and proper operation of this ﬁreplace.

WARNING: Any change to

this ﬁreplace or its controls can

be dangerous.

WARNING: Do not use a blow-

er insert, heat exchanger insert

or other accessory not approved

for use with this ﬁreplace.

WARNING: Do not allow fans

to blow directly into the ﬁreplace.

Avoid any drafts that alter burner

ﬂame patterns. Ceiling fans can

create drafts that alter burner

ﬂame patterns. Altered burner

patterns can cause sooting.

Due to high temperatures, the

appliance should be located out

of trafﬁc and away from furniture

and draperies.

Do not place clothing or other

ﬂammable material on or near

the appliance. Never place any

objects on the heater.

Fireplace front and screen be-

come very hot when running

heater. Keep children and adults

away from hot surfaces to avoid

burns or clothing ignition. Fire-

place will remain hot for a time

after shutdown. Allow surfaces

to cool before touching.

Carefully supervise young chil-

dren when they are in the room

with ﬁreplace. When using the

hand-held remote accessory

(Remote-Ready Models Only),

keep selector switch in the OFF

position to prevent children from

turning on burners with remote.

You must operate this ﬁreplace

with the ﬁreplace screen in place.

Make sure ﬁreplace screen is

closed before running ﬁreplace.

Keep the appliance area clear

and free from combustible ma-

terials, gasoline and other ﬂam-

mable vapors and liquids.

www.desatech.com 113133-01B

SAFETY INFORMATION

Continued

1. This appliance is only for use with the type

of gas indicated on the rating plate. This ap-

pliance is not convertible for use with other

gases.

2. Do not place propane/LP supply tank(s) in-

side any structure. Locate propane/LP supply

tank(s) outdoors.

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use

any phone in your building

• immediately call your gas supplier from a

neighborʼs phone. Follow the gas supplierʼs

instructions

• if you cannot reach your gas supplier, call

the ﬁre department

4. This ﬁreplace shall not be installed in a bed-

room or bathroom.

5. Do not use this ﬁreplace as a wood-burning

ﬁreplace. Use only the logs provided with

the ﬁreplace.

6. Do not add extra logs or ornaments such as

pine cones, vermiculite or rock wool. Using

these added items can cause sooting. Do not

add lava rock around base. Rock and debris

could fall into the control area of ﬁreplace.

7. This ﬁreplace is designed to be smokeless.

If logs ever appear to smoke, turn off ﬁre-

place and call a qualified service person.

Note: During initial operation, slight smoking

could occur due to log curing and ﬁreplace

burning manufacturing residues.

8. To prevent the creation of soot, follow the

instructions in Cleaning and Maintenance,

page 27.

9. Before using furniture polish, wax, carpet

cleaner or similar products, turn ﬁreplace off.

If heated, the vapors from these products may

create a white powder residue within burner

box or on adjacent walls or furniture.

10. This ﬁreplace needs fresh air ventilation to run

properly. This ﬁreplace has an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The

ODS shuts down the ﬁreplace if not enough

fresh air is available. See Air for Combustion

and Ventilation, page 6. If ﬁreplace keeps

shutting off, see Troubleshooting, page 29.

11. Do not run ﬁreplace

• where ﬂammable liquids or vapors are used

or stored.

• under dusty conditions.

12. Do not use this ﬁreplace to cook food or burn

paper or other objects.

13. Never place any objects in the ﬁreplace or

on logs.

14. Do not use ﬁreplace if any part has been under

water. Immediately call a qualiﬁed service

technician to inspect the room ﬁreplace and to

replace any part of the control system and any

gas control which has been under water.

15. Turn off and unplug ﬁreplace and let cool

before servicing. Only a qualiﬁed service

person should service and repair ﬁreplace.

16. Operating ﬁreplace above elevations of 4,500

feet could cause pilot outage.

17. Do not operate ﬁreplace if log is broken. Do

not operate ﬁreplace if log is chipped (dime-

sized or larger).

18. To prevent performance problems, do not use

propane/LP fuel tank of less than 100 lbs.

capacity.

19.

Provide adequate clearances around air

openings.

www.desatech.com

113133-01B 5

PRODUCT

IDENTIFICATION

Ignitor Button

Screen

Fireplace

Cabinet

Log

Control

Knob

Figure 1 - Vent-Free Compact Dual Flame

Fireplace

Hood

Fireplace Cabinet

Logs

Ignitor

Button

Remote Control

(Optional)

Control Knob

Hood

OPTIONAL REMOTE

CONTROL ACCESSORIES

(For Remote-Ready Models Only)

There are four optional remote controls that

can be purchased separately for Remote-Ready

Models only:

• wall switch

• hand-held ON/OFF remote

• wall thermostat

• hand-held thermostat remote

See Accessories, page 40.

LOCAL CODES

Install and use ﬁreplace with care. Follow all local

codes. In the absence of local codes, use the lat-

est edition of The National Fuel Gas Code ANSI

Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

PRODUCT FEATURES

SAFETY PILOT

This ﬁreplace has a pilot with an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The

ODS/pilot is a required feature for vent-free room

ﬁreplaces. The ODS/pilot shuts off the ﬁreplace if

there is not enough fresh air.

PIEZO IGNITION SYSTEM

This ﬁreplace has a piezo ignitor. This system

requires no matches, batteries or other sources to

light ﬁreplace.

THERMOSTATIC HEAT CONTROL

FOR THERMOSTAT-CONTROLLED

MODELS

Thermostat-Controlled models have a thermostat

sensing bulb and a control valve. The thermostat

will automatically modulate the heat output to

maintain a consistent room temperature. This

results in greater ﬁreplace comfort. This can also

result in lower gas bills.

UNPACKING

1. Remove fireplace and hood from carton.

Log is wrapped and inside ﬁreplace. Do not

remove at this time.

2. Remove all protective packaging applied to

ﬁreplace for shipment.

3. Make sure your ﬁreplace includes one hard-

ware packet.

4. Check ﬁreplace for any shipping damage. If

ﬁreplace is damaged, promptly inform dealer

where you bought ﬁreplace.

www.desatech.com 113133-01B

HOOD ASSEMBLY

WARNING: Always have

screen in place before operating

ﬁreplace. This prevents exces-

sive temperatures on ﬁreplace

surfaces.

WARNING: Failure to position

the parts in accordance with these

diagrams or failure to use only

parts speciﬁcally approved with

this ﬁreplace may result in prop-

erty damage or personal injury.

Tools Required:

• Phillips screwdriver • slotted screwdriver

• 5/16" hex wrench • scissors

1. Lift ﬁreplace screen up and pull out to remove

(see Figure 2). Set screen aside until installa-

tion has been completed.

2. Cut two plastic straps to remove the log from

the ﬁrebox cavity. Set log aside.

3. An optional blower is available. See Acces-

sories, page 40. Install optional blower now.

Follow installation instructions provided with

blower and see page 14 or 15, depending on

your installation.

4. Locate four black phillips sheet metal screws

in hardware packet.

5. Slide hood between louver and ﬁrebox top and

align screw holes.

6. Insert screws as shown in Figure 3. Tighten

screws ﬁrmly.

Figure 2 - Removing and Installing

Screen

Shoulder Screw

Figure 3 - Assembling Hood

Hood

Sheet Metal

Screws Firebox

Top

Louver

AIR FOR COMBUSTION

AND VENTILATION

WARNING: This ﬁreplace

shall not be installed in a con-

ﬁned space or unusually tight

construction unless provisions

are provided for adequate com-

bustion and ventilation air. Read

the following instructions to in-

sure proper fresh air for this and

other fuel-burning appliances in

your home.

Todayʼs homes are built more energy efﬁcient

than ever. New materials, increased insulation and

new construction methods help reduce heat loss

in homes. Home owners weather strip and caulk

around windows and doors to keep the cold air out

and the warm air in. During heating months, home

owners want their homes as airtight as possible.

While it is good to make your home energy efﬁ-

cient, your home needs to breathe. Fresh air must

enter your home. All fuel-burning appliances need

fresh air for proper combustion and ventilation.

Exhaust fans, ﬁreplaces, clothes dryers and fuel

burning appliances draw air from the house to

operate. You must provide adequate fresh air for

these appliances. This will insure proper venting

of vented fuel-burning appliances.

www.desatech.com

113133-01B 7

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Section 5.3,

Air for Combustion and Ventilation.

All spaces in homes fall into one of the three fol-

lowing ventilation classiﬁcations:

1. Unusually Tight Construction

2. Unconﬁned Space

3. Conﬁned Space

The information on pages 6 through 8 will help

you classify your space and provide adequate

ventilation.

Unusually Tight Construction

The air that leaks around doors and windows

may provide enough fresh air for combustion and

ventilation. However, in buildings of unusually

tight construction, you must provide additional

fresh air.

Unusually tight construction is deﬁned as

construction where:

a. walls and ceilings exposed to the out-

side atmosphere have a continuous

water vapor retarder with a rating of

one perm (6 x 10-11 kg per pa-sec-m2) or

less with openings gasketed or sealed

and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to

areas such as joints around window

and door frames, between sole plates

and ﬂoors, between wall-ceiling joints,

between wall panels, at penetrations

for plumbing, electrical and gas lines

and at other openings.

If your home meets all of these three

criteria, you must provide additional

fresh air. See Ventilation Air From

Outdoors, page 8.

If your home does not meet all of the three

criteria above, proceed to Determining

Fresh-Air Flow For Fireplace Location,

column 2.

AIR FOR COMBUSTION

AND VENTILATION

Continued

Conﬁned and Unconﬁned Space

The National Fuel Gas Code, ANSI Z223.1/NFPA

54 deﬁnes a conﬁned space as a space whose

volume is less than 50 cubic feet per 1,000 Btu

per hour (4.8 m3 per kw) of the aggregate input

rating of all appliances installed in that space and

an unconﬁned space as a space whose volume is

not less than 50 cubic feet per 1,000 Btu per hour

(4.8 m3 per kw) of the aggregate input rating of

all appliances installed in that space. Rooms com-

municating directly with the space in which the

appliances are installed*, through openings not

furnished with doors, are considered a part of the

unconﬁned space.

* Adjoining rooms are communicating only if

there are doorless passageways or ventilation grills

between them.

DETERMINING FRESH-AIR FLOW

FOR FIREPLACE LOCATION

Determining if You Have a Conﬁned or

Unconﬁned Space

Use this work sheet to determine if you have a

conﬁned or unconﬁned space.

Space: Includes the room in which you will install

ﬁreplace plus any adjoining rooms with doorless pas-

sageways or ventilation grills between the rooms.

1. Determine the volume of the space (length x

width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example: Space size 16 ft. (length) x 14 ft.

(width) x 8 ft. (ceiling height) = 1792 cu. ft.

(volume of space)

If additional ventilation to adjoining room is

supplied with grills or openings, add the volume

of these rooms to the total volume of the space.

2. Multiply the space volume by 20 to determine

the maximum Btu/Hr the space can support.

__________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example: 1792 cu. ft. (volume of space) x 20 =

35,840 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in

the space.

Vent-free ﬁreplace ___________ Btu/Hr

Gas water heater* ___________ Btu/Hr

Gas furnace ___________ Btu/Hr

Vented gas heater ___________ Btu/Hr

Gas ﬁreplace logs ___________ Btu/Hr

Other gas appliances* + ___________ Btu/Hr

Total = ___________ Btu/Hr

* Do not include direct-vent gas appliances. Di-

rect-vent draws combustion air from the outdoors

and vents to the outdoors.

www.desatech.com 113133-01B

AIR FOR COMBUSTION

AND VENTILATION

Continued

Example:

Gas water heater _________ Btu/Hr

Vent-free ﬁreplace _________ Btu/Hr

Total _________ Btu/Hr

4. Compare the maximum Btu/Hr the space can

support with the actual amount of Btu/Hr used.

_________

Btu/Hr (maximum the space can support)

_________

Btu/Hr (actual amount of Btu/Hr used)

Example: 35,840 Btu/Hr (maximum the space

can support)

40,000 Btu/Hr (actual amount of

Btu/Hr used)

The space in the above example is a conﬁned space

because the actual Btu/Hr used is more than the maxi-

mum Btu/Hr the space can support. You must provide

additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoin-

ing room. If the extra space provides an unconﬁned

space, remove door to adjoining room or add

ventilation grills between rooms. See Ventilation

Air From Inside Building.

B. Vent room directly to the outdoors. See Ventila-

tion Air From Outdoors.

C. Install a lower Btu/Hr ﬁreplace, if lower Btu/Hr

size makes room unconﬁned.

If the actual Btu/Hr used is less than the maximum

Btu/Hr the space can support, the space is an un-

conﬁned space. You will need no additional fresh

air ventilation.

WARNING: If the area in

which the ﬁreplace may be oper-

ated is smaller than that deﬁned

as an unconﬁned space or if the

building is of unusually tight

construction, provide adequate

combustion and ventilation air

by one of the methods described

in the National Fuel Gas Code,

ANSI Z223.1/NFPA 54 Section 5.3

or applicable local codes.

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining un-

conﬁned space. When ventilating to an adjoining

unconﬁned space, you must provide two perma-

nent openings: one within 12" of the ceiling and

one within 12" of the ﬂoor on the wall connecting

the two spaces (see options 1 and 2, Figure 4). You

can also remove door into adjoining room (see

option 3, Figure 4). Follow the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for

Combustion and Ventilation for required size of

ventilation grills or ducts.

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or

ducts. You must provide two permanent openings:

one within 12" of the ceiling and one within 12"

of the ﬂoor. Connect these items directly to the

outdoors or spaces open to the outdoors. These

spaces include attics and crawl spaces. Follow the

National Fuel Gas Code, ANSI Z223.1/NFPA 54,

Section 5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

IMPORTANT: Do not provide openings for inlet

or outlet air into attic if attic has a thermostat-

controlled power vent. Heated air entering the attic

will activate the power vent.

30,000

+ 10,000

= 40,000

Figure 5 - Ventilation Air from Outdoors

Outlet

Air

Ventilated

Attic

Outlet

Inlet

Air

Inlet Air Ventilated

Crawl Space

Crawl

Space

To Attic

Figure 4 - Ventilation Air from Inside

Building

Remove

Door into

Adjoining

Room,

Option

Ventilation Grills

Into Adjoining Room,

Option 2

Ventilation

Grills

Into Adjoining

Room,

Option 1

12"

www.desatech.com

113133-01B 9

INSTALLATION

NOTICE: This heater is intended

for use as supplemental heat.

Use this heater along with your

primary heating system. Do not

install this heater as your pri-

mary heat source. If you have a

central heating system, you may

run system’s circulating blower

while using heater. This will help

circulate the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

WARNING: A qualiﬁed ser-

vice person must install ﬁre-

place. Follow all local codes.

WARNING: Never install the

ﬁreplace

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing or other ﬂammable

objects are less than 36 inches

from the front, top or sides of

the ﬁreplace

• as a ﬁreplace insert

• in high trafﬁc areas

• in windy or drafty areas

WARNING: Never install in a

bedroom or bathroom. Any heat-

ing product with a Btu/Hr rating

over 10,000 cannot be used in a

bedroom.

CAUTION: This ﬁreplace cre-

ates warm air currents. These

currents move heat to wall sur-

faces next to ﬁreplace. Installing

ﬁreplace next to vinyl or cloth

wall coverings or operating

ﬁreplace where impurities (such

as, but not limited to, tobacco

smoke, aromatic candles, clean-

ing ﬂuids, oil or kerosene lamps,

etc.) in the air exist, may discolor

walls or cause odors.

IMPORTANT: Vent-free ﬁreplaces add moisture

to the air. Although this is beneﬁcial, installing ﬁre-

place in rooms without enough ventilation air may

cause mildew to form from too much moisture. See

Air for Combustion and Ventilation, page 6.

Note: Your ﬁreplace is designed to be used in zero

clearance installations. Wall or framing material

can be placed directly against any exterior surface

on the rear, sides or top of your ﬁreplace, except

where standoff spacers are integrally attached. If

standoff spacers are attached to your ﬁreplace,

these spacers can be placed directly against wall

or framing materials.

Note: When installing ﬁreplace directly on carpet-

ing, tile or other combustible material, other than

wood ﬂooring, the ﬁreplace shall be installed on a

metal or wood panel extending the full width and

depth of the ﬁreplace.

Use the dimensions shown for rough openings to

create the easiest installation (see Built-In Fire-

place Installation, page 11).

CHECK GAS TYPE

Use the correct gas type (natural or propane/LP)

for your unit. If your gas supply is not correct, do

not install ﬁreplace. Call dealer where you bought

ﬁreplace for proper type ﬁreplace.

WARNING: This appliance

is equipped for (natural or pro-

pane/LP) gas. Field conversion

is not permitted.

www.desatech.com 113133-01B

INSTALLATION ITEMS

Before installing ﬁreplace, make sure you have

the items listed below.

• external regulator (supplied by installer, for

propane/LP units only)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• test gauge connection*

• ground joint union

• sediment trap

• tee joint

• pipe wrench

* A CSA design-certiﬁed equipment shutoff valve

with 1/8" NPT tap is an acceptable alternative to

test gauge connection. Purchase the optional CSA

design-certiﬁed equipment shutoff valve from your

dealer. See Accessories, page 40.

Note: If desired, purchase a four-sided perimeter

trim kit for built-in installations. See Accessories,

page 40.

FIREPLACE CLEARANCES

WARNING: Maintain the

minimum clearances shown

in Figure 6. If you can, provide

greater clearances from ﬂoor,

ceiling and joining wall.

If your ﬁreplace is to be used with an optional

mantel, the installation instructions included with

your mantel shows an CSA approved method of

attaching the ﬁreplace/mantel system to a wall.

IMPORTANT: Only use optional cabinet or

corner mantels speciﬁed in this manual. Purchase

the optional mantel from your dealer (see Acces-

sories, page 40).

If your ﬁreplace is to be recessed into the wall,

see Built-In Fireplace Installation on page 11 to

secure your ﬁreplace into the wall.

CAUTION: If you install the

ﬁreplace in a home garage

• ﬁreplace pilot and burner must

be at least 18 inches above

ﬂoor.

• locate ﬁreplace where moving

vehicle will not hit it.

INSTALLATION

Continued

For convenience and efﬁciency, install ﬁreplace

• where there is easy access for operation, inspec-

tion and service

• in coldest part of room

An optional blower kit is available from your

dealer. See Accessories, page 40. If planning to use

blower, follow instructions provided with blower

for power source.

Minimum Clearances For Side

Combustible Material, Side Wall and

Ceiling

A. Clearances from the side of the fireplace

cabinet to any combustible material and wall

should follow diagram in Figure 6.

Example: The face of a mantel, bookshelf,

etc. is made of combustible material and

protrudes 3 1/2" from the wall. This combus-

tible material must be 4" from the side of the

ﬁreplace opening (see Figure 6).

Clearances from the top of the ﬁreplace opening

to the ceiling should not be less than 36 inches.

For mantel clearances, see Figure 10 on

page 12.

MINIMUM CLEARANCE TO

COMBUSTIBLE MATERIALS

Top Left and Bottom

Right Sides and Rear

36" 6" 0"

Figure 6 - Minimum Clearance for

Combustible to Wall

*Minimum 16 inches from Side Wall

Example

This manual suits for next models

Table of contents

Other Desa Indoor Fireplace manuals

Desa

Desa CFFP18NT Quick start guide

Desa

Desa W26LTF Instruction manual

Desa

Desa (V)G36HR Safety guide

Desa

Desa 3612ST User manual

Desa

Desa V50S Quick start guide

Desa

Desa Variable Manually-Controlled Models Quick start guide

Desa

Desa VKC36PE Series Quick start guide

Desa

Desa Comfort Glow CGEFP33PR Quick start guide

Desa

Desa T32N, T36N, T32P, T36P Operation manual

Desa

Desa VB42I User manual

Desa

Desa Comfort Glow CGCF26TNA Quick start guide

Desa

Desa CHAM55N Original instructions

Desa

Desa (V)V42PA(1) Quick start guide

Desa

Desa GMC55FA Instruction manual

Desa

Desa Vanguard VMH26TNB Quick start guide

Desa

Desa (V)KC42NE SERIE Quick start guide

Desa

Desa V36N SERIES Quick start guide

Desa

Desa VFF-32S-AKA Quick start guide

Desa

Desa Comfort Glow RFP28TC Quick start guide

Desa

Desa CCFPDFT Operation manual

Desa

Desa FPVF33NRA Quick start guide

Desa

Desa VT36ENA Series Quick start guide

Desa

Desa B36 User manual

Desa

Desa (V)GM36 Quick start guide

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Miles Industries

Miles Industries Vogue 1300IRN Installation & operating instructions