Desa P324E Quick start guide

For more information, visit www.desatech.com

MODELS P324E, VP324E, P325E(B) AND VP325E(B)

NATURAL GAS

B-VENT DECORATIVE GAS FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

FOR YOUR SAFETY

— Donotstoreorusegasolineoranyotherammable

vapors or liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS :

• Do not try to light any appliance.

• Do not touch any electrical switch;

• Donotuseanyphoneinyourbuilding.

• Immediatelycallyourgassupplierfromaneighbor’s

phone.Followthegassupplier’sinstructions.

• Ifyoucannotreachyourgassupplier,callthere

department.

— Installationandservicemustbeperformedbyaquali-

edinstaller,serviceagencyorthegassupplier.

INSTALLER:Leavethismanualwiththeappliance.

CONSUMER:Retainthismanualforfuturereference.

WARNING:Iftheinformationintheseinstructions

isnotfollowedexactly,areorexplosionmayresult

causingpropertydamage,personalinjuryordeath.

www.desatech.com 108794-01F2

 WARNING: Improper installation, adjustment, al-

teration, service or maintenance can cause injury or

propertydamage.Refertothismanualforcorrectin-

stallation and operational procedures. For assistance

or additional information consult a qualied installer,

service agency or the gas supplier.

NOT FOR USE WITH SOLID FUEL

CHECK LOCAL CODES PRIOR TO INSTALLATION

SAVE THIS BOOK

Thisbookisvaluable.Inadditiontoinstructingyouon

howtoinstallandmaintainyourappliance,italsocon-

tainsinformationthatwillenableyoutoobtainreplace-

mentpartsoroptionalaccessoryitemswhenneeded.

Keepitwithyourotherimportantpapers.

Thisappliancemaybeinstalledinanaftermarket*,per-

manentlylocated,manufactured(mobile)home,where

notprohibitedbystateorlocalcodes.

This appliance is only for use with the type of gas indi-

cated on the rating plate.

This appliance is not convertible for use with other

gases,unlessacertiedkitisused.

*Aftermarket:Completionofsale,notforpurposeofresale,fromthemanufacturer.

TABLE OF CONTENTS

Safety .................................................................. 3

Unpacking............................................................ 4

Introduction.......................................................... 4

Selecting Location ............................................... 5

Product Specications......................................... 6

Pre-Installation Preparation................................. 7

Venting Installation .............................................. 8

Fireplace Installation...........................................11

Operation........................................................... 18

Inspecting Burners ............................................ 19

Cleaning and Maintenance................................ 20

Replacement Parts............................................ 20

Service Hints ..................................................... 20

Technical Service............................................... 20

Wiring Diagram.................................................. 21

Troubleshooting................................................. 22

Accessories ....................................................... 25

Parts .................................................................. 26

Warranty ..............................................Back Cover

www.desatech.com

108794-01F 3

SAFETY

WARNING:This product con-

tainsand/orgenerateschemicals

knowntotheStateofCalifornia

tocausecancerorbirthdefects

orotherreproductiveharm.

IMPORTANT:Readthisowner’s

manualcarefullyandcompletely

before trying to assemble, op-

erate or service this replace.

Improper use of this replace

cancauseseriousinjuryordeath

from burns, re, explosions,

electrical shock and carbon

monoxidepoisoning.

DANGER:Carbonmonoxide

poisoningmayleadtodeath!

This replace is a vented product. This replace

will not produce any gas leakage into your home

if properly installed. This replace must be

properly installed by a qualied service person.

If this unit is not properly installed by a qualied

service person, gas leakage can occur.

CarbonMonoxidePoisoning: Early signs of

carbon monoxide poisoning resemble the u,

with headaches, dizziness or nausea. If you

have these signs, the replace may not have

been installed properly. Getfreshairatonce!

Have replace inspected and serviced by a

qualied service person. Some people are more

affected by carbon monoxide than others. These

include pregnant women, people with heart or

lung disease or anemia, those under the inu-

ence of alcohol and those at high altitudes.

Propane/LP gas and natural gas are both

odorless. An odor-making agent is added

to each of these gases. The odor helps you

detect a gas leak. However, the odor added

to these gases can fade. Gas may be present

even though no odor exists.

Make certain you read and understand all

warnings. Keep this manual for reference. It

is your guide to safe and proper operation of

this replace.

WARNING: Any change to

thisreplaceoritscontrolscan

bedangerous.

1. This appliance is only for use with the

type of gas indicated on the rating plate.

This appliance is not convertible for use

with other gases unless a certied kit is

used.

2. For propane/LP replace, do not place

propane/LP supply tank(s) inside any

structure. Locate propane/LP supply

tank(s) outdoors. To prevent performance

problems, do not use propane/LP fuel tank

of less than 100 lbs. capacity.

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not

use any phone in your building

• immediately call your gas supplier from

a neighbor’s phone. Follow the gas

supplier's instructions

• if you cannot reach you gas supplier, call

the re department.

4. Never install the replace

• in a recreational vehicle

• where curtains, furniture, clothing or

other ammable objects are less than

36" from the front and 42" from the top

top of the replace. For side clearances

see Figure 6, page 7

• in high trafc areas

• in windy or drafty areas

5. This replace reaches high temperatures.

Keep children and adults away from hot

surfaces to avoid burns or clothing igni-

tion. Fireplace will remain hot for a time

after shutdown. Allow surfaces to cool

before touching.

6. Carefully supervise young children when

they are in the room with replace.

7. A hearth extension is not required with this

appliance. If one is installed, it is for aes-

thetic purposes only and does not have

to meet the standard requirements.

8. Turn replace off and let cool before ser-

vicing or repairing. Only a qualied service

person should install, service or repair

this replace. Have replace inspected

annually by a qualied service person.

9. You must keep control compartments,

burners and circulating air passages

clean. More frequent cleaning may be

needed due to excessive lint and dust

from carpeting, bedding material, etc.

Turn off the gas valve and pilot light before

cleaning replace.

10. Have venting system inspected annually by

a qualied service person. If needed, have

venting system cleaned or repaired. See

Cleaning and Maintenance, page 20.

www.desatech.com 108794-01F4

11. Keep the area around your fireplace

clear of combustible materials, gasoline

and other ammable vapor and liquids.

Do not run fireplace where these are

used or stored. Do not place items such

as clothing or decorations on or around

replace.

12. Do not use this replace to cook food or

burn paper or other objects.

13. Do not use any solid fuels (wood, coal,

paper, cardboard, etc.) in this replace.

Use only the gas type indicated on re-

place nameplate.

14. This appliance, when installed, must be

electrically grounded in accordance with

local codes or, in the absence of local

SAFETY

Continued

These replace models are vented gas re-

places that use an electronic ignition system.

Models P325E/VP325E have a 5" B-vent and

P324E/VP324EA have a 4" B-vent. A properly

sized B-type venting system and a listed type

vent cap are not supplied but are required for

proper operation. See venting instructions

on page 9.

WARNING: This gas appli-

ancemustnotbeconnectedto

achimneyueservicingasolid

fuelburningappliance.

These models are factory equipped for use

with natural gas and must be converted when

intended for use with proper propane/LP gas.

Conversion kits PCBE-324 and PCBE-325

may be purchased for simple conversion to

propane/LP gas. See Accessories, page 25.

BEFORE YOU BEGIN

Before beginning installation of your appli-

ance, read these instructions completely.

codes, with the National Electrical Code,

ANSI/NFPA 70 or the Canadian Electrical

Code, CSA C22.1.

15. Do not install replace directly on carpet-

ing, vinyl tile or any combustible material

other than wood. The replace must set

on a metal or wood panel extending the

full width and depth of the replace.

16. Do not use replace if any part has been

exposed to or under water. Immediately

call a qualied service person to arrange

for replacement of the unit.

17. Do not operate fireplace if any log is

broken.

18. Provide adequate clearances around air

openings.

UNPACKING

The following items are packed inside the

rebox. Remove before positioning rebox

into framing.

• Ceramic Log Pack - Shrink-wrapped on

cardboard

• Three (3) plastic bags containing lava rock,

pan and ember materials

• Rear Log (P325E/VP325E Models Only)-

Remove the two plastic quick ties from

around burner and grate

• Grate Stand - Lift off of burner pan

Check all items for any shipping damage. If

damaged, promptly inform dealer or distributor

where you bought the product.

Safely retain these items for later installation.

INTRODUCTION

This DESA Heating, LLC appliance and its

approved components are safe when installed

according to this installation manual and are

operated as recommended by DESA Heating,

LLC. Unless you use DESA Heating, LLC ap-

proved components tested for this appliance,

YOUMAYCAUSEAFIREHAZARD!

The DESA Heating, LLC warranty will be

voided by and DESA Heating, LLC disclaims

any responsibility for the following actions :

A) Modication of the appliance or any of the

components.

B) Use of any component part not approved

by DESA Heating, LLC in combination

with this appliance.

C) Installation and/or operation in a manner

other than instructed in this manual.

D) The burning of anything other than the

type of gas approved for use in this gas

appliance.

The installation must conform with local

codes or, in the absence of local codes, with

the current National Fuel Gas Code, ANSI

Z223.1/NFPA 54. This appliance complies

with ANSI Z21.50-2000.

www.desatech.com

108794-01F 5

WARNING: Installation of

thisapplianceshould bedone

by a qualied service person

well trained in the installation

of such appliances. You will

alsoneedabuildingpermitfrom

your local Building and Safety

Commissionerbeforeinstalling

this appliance; otherwise your

insurance company may not

cover this appliance.

NOTICE: This appliance is not

intendedtobeusedasaprimary

source of heat.

INTRODUCTION

Continued

Figure 1 - Possible Locations for

Installing Appliance

INTERNAL WALL

INSTALLATION

CORNER

INSTALLATION

FULL

PROJECTION

INSTALLATION

FLUSH

INSTALLATION

To determine the safest and most efcient

location for your appliance, you must take into

consideration the following guidelines:

1. The location must allow for proper clear-

ances (see Clearances, page 7).

2. Consider a location where heat output

would not be affected by drafts, air con-

ditioning ducts, windows or doors.

3. A location that avoids the cutting of joists

or roof rafters will make installation easier.

Figure 1 shows a plan view of a few com-

mon locations.

Flush installations are recommended where

living space is limited or at a premium and

since the space required to enclose the ap-

pliance would be located beyond an outside

wall, this would also reduce the cutting of

joists, roof rafters and such. Check local

codes for any restrictions.

Projected installations can extend any

distance into the room. A projection may

be ideal for a new addition on an existing,

nished wall.

CAUTION: Do not connect

appliancebeforepressuretest-

inggaspiping.Damagetogas

valvemayresultandanunsafe

conditionmaybecaused.

The appliance and it’s individual shutoff valve

must be disconnected from the gas supply

piping system during any pressure testing of

that system at test pressures in excess of 1/2

psig (3.5 kPa).

The appliance must be isolated from the gas

supply piping system by closing its individual

manual shutoff valve during any pressure

testing of the gas supply piping system at

test pressures equal to or less than 1/2 psig

(3.5 kPa).

For the purpose of input adjustment two

pressure taps (for IN and OUT pressures)

are provided on the gas control valve for test

gauge connections to the appliance.

SELECTING LOCATION

Corner installations make use of space

that may not normally be used and provides

a wider and more efcient range for radiant

heat transference.

Internal wall installations provide a discreet

option for room separation and can also be

ideal as an addition to an existing wall.

www.desatech.com 108794-01F6

PRODUCT SPECIFICATIONS

Figure 2 - Appliance Dimensions

Alternate Gas

Supply Inlet

* 27

29"

* 13

* 20

For Use

With B-1

Vent Pipe

Only 16

5/8" 34

* WITH REFRACTORY

DIMENSIONS

HEARTH AREA

GAS RATING - NATURAL

P324E, VP324E P325E(B),VP325E(B)

Max. Input Rating: 15,000 Btu/Hr 25,000 Btu/Hr

Manifold Pressure: 3.5" WC (.87 kPa) 3.5" WC (.87 kPa)

Minimum Supply Pressure: 4.5" WC (1.12 kPa) 4.5" WC (1.12 kPa)

Maximum Supply Pressure: 10.5" WC (2.66 kPa) 10.5" WC (2.66 kPa)

Orice Size: # 49 # 40

GAS RATING - PROPANE/LP

Max. Input Rating: 15,000 Btu/Hr 25,000 Btu/Hr

Manifold Pressure: 10" WC (2.49 kPa) 10" WC (2.49 kPa)

Minimum Supply Pressure: 11" WC (2.74 kPa) 11" WC (2.74 kPa)

Maximum Supply Pressure: 13" WC (3.23 kPa) 13" WC (3.23 kPa)

Orice Size: # 56 # 54

www.desatech.com

108794-01F 7

PRE-INSTALLATION PREPARATION

Figure 3 - Minimum Clearances

(Top View)

0" Clearance

Nailing

Flange

Front Face

Left Side

Surround Back

Drywall

2 x 4 Stud

Figure 4 - Minimum Clearances

(Front View)

MANTEL CLEARANCES AND WALL

DETAILS

A combustible mantle shelf maybe installed

a maximum 12" (22.90 cm) from the wall.

Figures 5 and 6 show the minimum allow-

able distances from various combustible

mantle components in relation to the replace

opening.

Figure 5 - Mantel Clearances - Side View

(Cross Section)

Figure 6 - Side Clearances - Top View

(Cross Section)

42" (10.67 cm)

Min. Clearance

from Opening to

Ceiling

0" Clearance

Ceiling

1" (2.5 cm) Min.

Clearance to

"B" Vent's Outer Pipe

Required

Air Spaces

are Indicated

with an "

Do Not

Pack with

Insulation or

Any Other

Material

DO NOT BLOCK

OR OBSTRUCT

OPENINGS

0" Clearance

to Wood or

Noncombustible

Flooring

Spacer

3" (7.6 cm)

1 1/2"

(3.8 cm) Max.

8" (20.3 cm)

6" (15.2 cm)

13" (33 cm)

12"

(22.9 cm)

Combustible

Materials

Header

1 1/2" (3.8 cm)

Max.

3" (7.6 cm)

Max.

6" (15.2 cm)

Max. 9"

(22.86 cm)

12"

(30.48 cm)

Outer Surround

Combustible

Material May

Be Used

TOP VIEW

SAFE

ZONE

Perpendicular

Wall

CLEARANCES

Minimum clearances to combustibles are:

• Top of Spacers 0" min.

• Back/Sides of Outer Surround 0" min.

• Drywall to Sides of Front Face

(Nailing Flanges) 0" min.

• “B” Vent Surfaces 1" min.

• Ceiling to Opening 42" min.

• Floor 0" min.

• Perpendicular Wall See Figure 6

 CAUTION: Do not block

required air spaces with insu-

lationoranyothermaterial.Do

not obstruct effective opening

of appliance with any type of

facingmaterial.

www.desatech.com 108794-01F8

PRE-INSTALLATION PREPARATION

Continued

FRAMING

1. Frame appliance enclosure as illustrated

in Figures 7 and 8.

Note: If a wall covering is used to line

enclosure, then all measurements must

be from surface of covering.

2. Place appliance into framing and secure.

Note: If appliance is to be raised above

oor level, a platform must be built to

support appliance.

3. Install supply line to appliance using a

1/2" NPT black iron gas line terminating

2 5/16" above bottom of appliance. The gas

line must be installed through the lower

left side access point or alternate access

hole in bottom of appliance (see Figure

16, page 12).

4. Feed exible gas line through one of three

gas line conduit sleeves and repack insu-

lation to cover any openings. Prepare the

incoming gas line with teon tape or pipe

joint compound and hook up incoming gas

line to exible gas line.

Note: If 1/2" NPT black iron pipe does not

mate with tting at end of exible gas line,

remove tting and replace with a 37° are

3/4"-12, 1/2" NPT (female) tting.

 WARNING: When nishing

appliance,donotoverlapcom-

bustiblematerialontotheblack

frontface.Brick,tileorothernon-

combustible materials may be

applied to the face provided that

anygapisbetweenthematerial

usedandthefaceiscaulkedwith

anoncombustiblecaulking.

Figure 7 - Rough Opening for Installing

in Wall

Figure 8 - Corner Installation Guidelines

16 3/4"

12"

39 3/8"

55 5/8"

34 1/2"

16"

These Dimensions Allow for a 3/4"

Clearance at Sides and Back of Fireplace.

However, 0" Clearance is Permitted

3/4" Clearance Not Required at

Nailing Flanges

VENTING INSTALLATION

16 1/8"

34 3/4"

36 5/8"

A B-type venting system must be connected to

appliance for venting to outside of building.

The following section is provided as a guide

to a standard B-type vent installation.

Standing codes requirements concerning B-

type vent installations may vary within your

state, province or local codes jurisdiction.

Therefore, it is recommended that you check

with your local building codes for specic

requirements or in absence of local codes,

follow Section 7.0 of the current National Fuel

Gas Code ANSI Z223.1/NFPA 54.

This gas appliance must be vented to the

outdoors only and may not be terminated into

an attic space or into a chimney ue servicing

a solid fuel burning appliance.

www.desatech.com

108794-01F 9

This appliance may be vented through a

manufactured chimney system or a masonry

chimney using a B-vent adapter or a chim-

ney liner system if all are listed, inspected

and approved by local codes and/or building

authorities.

The examples shown in Figure 9 are typi-

cal of most B-vent installations and codes

practices.

Example1: Shows the minimum allowable

system height and lateral offset for a 60° or

greater inclination. Code species that offsets

at 60° or greater are considered horizontal

and must follow the 75% rule for lateral to

total vertical system height. Codes also al-

lows only one offset in the total system when

at 60° or greater. The total vertical height in

this example represents the minimum height

of 8 feet and therefore the allowable lateral

is 6 feet when the 75% rule applies. If the

lateral length must exceed 75% then the

system must be sized in accordance with the

Category I venting tables.

Example2: Shows a multiple offset each at

45° of inclination. Multiple offsets are permit-

ted if they do not exceed 45° of inclination. The

total lengths of the two offsets are not required

to meet the 75% allowable rule.

Example3:Shows a single offset at 45° of

inclination and therefore the lateral length at

10 feet of offset does not have to meet the

75% rule.

Maintain

Listed

Clearance

Maintain

Listed

Clearance

12' Min.

12' Min. 45°

45°

12' Min.

60° 45°

Position

Firestop

Position

Firestop

Position

Firestop

Listed

Vent Cap

Listed

Vent Cap

Listed

Vent Cap

Maintain

Listed

Clearance

Maintain

Listed

Clearance

Maintain

Listed

Clearance

Maintain

Listed

Clearance

Support Each

Lateral At

Least Every

6 Feet

Maintain

Listed

Clearance

10'

EXAMPLE 3EXAMPLE 2

EXAMPLE 1

Figure 9 - Typical B-Vent Conguration

VENTING INSTALLATION

Continued

In each case the offsets must be supported

and restops must be positioned wherever

the vent must pass through a sub-oor, ceil-

ing joist or an attic overhang. The vent pipe

must terminate vertically into a listed type vent

cap and extend a sufcient height through

an approved roof ashing, roof jack or a roof

thimble. At all points the listed clearances

must be maintained.

Vent terminations must be located in ac-

cordance with height and proximity rules of

NFPA No. 54. These rules apply to vents at

12" diameter or less and require a minimum

height in accordance with the roof pitch and a

minimum of 8 feet distance from a vertical wall

or obstruction (see Figure 10, page 10).

If venting horizontally through a side wall be-

comes necessary, a listed thimble approved

for use with B-type vent must be used. Check

with your local codes before venting through

a side wall.

Some codes areas allow the use of existing B-

type vent systems if the system is at or above

the recommended diameter of the ue.

The ue connection must be made using

listed B-type connectors and the existing

system must be code inspected for damage

and proper installation.

www.desatech.com 108794-01F10

VENTING INSTALLATION

Continued

It is not recommended that this appliance be

common vented with an existing gas burning

appliance. However, if it becomes necessary

to common vent this appliance, the venting

system must be sized and congured in ac-

cordance with the common venting guides

Appendix G of the current National Fuel Gas

Code NFPA No. 54/ANSI Z223.1.

Note: Before connecting this appliance to an

existing vent system or a common venting

system consult with your local architect, plan-

ner, or building ofcial.

WARNING: This appliance

must be properly connected

to a system and must not be

connected to a chimney ue

servicing a separate solid fuel

burningappliance.

CHECKING FOR PROPER VENTING

After completing and checking electrical,

gas and vent connections, follow lighting

instructions and allow main burner to run

for approximately 5 minutes. Hold a lighted

match or cigarette near top edge of replace

opening and play it along entire length of

the opening (see Figure 12). Proper venting

should tend to draw the ame or smoke into

the appliance. Improper venting or escaping

of spillage of burned gas, is indicated when

the match ickers or goes out. Smoke from a

cigarette will also tend to disperse away from

the appliance.

If the appliance is found to be improperly

venting, shut it off and notify your installer

or a qualied service agency to inspect the

venting system.

NOTICE: This appliance is

equipped with a vent safety

shutoff switch which will shut

down the appliance in the case

of a venting problem. Do not

bypasstheventsafetyswitch.If

the appliance should shut down,

contactaqualiedinstaller,ser-

vice agency or your gas supplier

tohavetheventinspectedbefore

operating.

Lowest

Discharge

Opening

Listed

Vent Cap

8 Ft. Min.

Roof Pitch x/12

Listed Clearance

Listed

Gas

Vent

H (Min)

Height

From Roof

Roof Pitch H(Min.)Ft. m

Flat to 6/12 1.0 0.30

6/12 to 7/12 1.25 0.38

Over 7/12 to 8/12 1.5 0.46

Over 8/12 to 9/12 2.0 0.61

Over 9/12 to 10/12 2.5 0.76

Over 10/12 to 11/12 3.25 0.99

Over 11/12 to 12/12 4.0 1.22

Over 12/12 to 14/12 5.0 1.52

Over 14/12 to 16/12 6.0 1.83

Over 16/12 to 18/12 7.0 2.13

Over 18/12 to 20/12 7.5 2.27

Over 20/12 to 21/12 8.0 2.44

Figure 10 - B-Vent Terminations

Check this area

along entire top

edge of replace

opening. Smoke

or ame should

be drawn into

appliance opening.

Figure 11 - Checking for Spillage

Other manuals for P324E

This manual suits for next models

Table of contents

Other Desa Indoor Fireplace manuals

Desa

Desa VV36ENA1 Series Quick start guide

Desa

Desa Vanguard EVGL850N Quick start guide

Desa

Desa (V)C36LH User manual

Desa

Desa VTGF33NRB Quick start guide

Desa

Desa (V)GM36 Quick start guide

Desa

Desa FPVF33PRA Quick start guide

Desa

Desa Comfort Glow CGF265NVA Quick start guide

Desa

Desa (V)V42NA(1) Quick start guide

Desa

Desa VDDVF36PN/PP Quick start guide

Desa

Desa BCS18, BCS24, BCS30 Quick start guide

Desa

Desa VVC36PE Series Quick start guide

Desa

Desa HGC23TON User manual

Desa

Desa G42 Safety guide

Desa

Desa VB42I User manual

Desa

Desa Vanguard VVSR18 Quick start guide

Desa

Desa VT32EN Series Quick start guide

Desa

Desa LGCFTN Quick start guide

Desa

Desa TUDOR Quick start guide

Desa

Desa Vanguard VSGF28NVA Quick start guide

Desa

Desa Vanguard VMH26TPC Quick start guide

Desa

Desa S42 Series Quick start guide

Desa

Desa C32GO Instruction manual

Desa

Desa (V)KC42NE SERIE Quick start guide

Desa

Desa UNVENTED (VENT-FREE) NATURAL GAS FIREPLACE Operation manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Miles Industries

Miles Industries Vogue 1300IRN Installation & operating instructions