Desa M36B Safety guide

For more information, visit www.desatech.com

NATURAL GAS MODELS

M36(B,H), M42(B,H), VM36(B,H)

AND VM42(B,H)

PROPANE/LP GAS MODELS

M36P(B,H), M42P(B,H),

VM36P(B,H) AND VM42P(B,H)

B-VENT DECORATIVE GAS FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

FOR YOUR SAFETY

— Donotstoreorusegasolineoranyotherammable

vapors or liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS :

• Donottrytolightanyappliance.

• Donottouchanyelectricalswitch;

• Donotuseanyphoneinyourbuilding.

• Immediatelycallyourgassupplierfromaneighbor’s

phone.Followthegassupplier’sinstructions.

• Ifyoucannotreachyourgassupplier,callthere

department.

— Installationandservicemustbeperformedbyaquali-

edinstaller,serviceagencyorthegassupplier.

INSTALLER:Leavethismanualwiththeappliance.

CONSUMER:Retainthismanualforfuturereference.

WARNING:Iftheinformationintheseinstructions

isnotfollowedexactly,areorexplosionmayresult

causingpropertydamage,personalinjuryordeath.

O-TL REPORT # 114-F-16-4

www.desatech.com 108795-01V2

 WARNING: Improper installation, adjustment, al-

teration, service or maintenance can cause injury or

propertydamage.Refertothismanualforcorrectin-

stallation and operational procedures. For assistance

or additional information consult a qualied installer,

service agency or the gas supplier.

NOT FOR USE WITH SOLID FUEL

CHECK LOCAL CODES PRIOR TO INSTALLATION

SAVE THIS BOOK

Thisbookisvaluable.Inadditiontoinstructingyouon

howtoinstallandmaintainyourappliance,italsocon-

tainsinformationthatwillenableyoutoobtainreplace-

mentpartsoroptionalaccessoryitemswhenneeded.

Keepitwithyourotherimportantpapers.

Thisappliancemaybeinstalledinanaftermarket*,per-

manentlylocated,manufactured(mobile)home,where

notprohibitedbystateorlocalcodes.

Thisapplianceisonlyforusewiththetypeofgasindi-

cated on the rating plate.

This appliance is not convertible for use with other

gases,unlessacertiedkitisused.

*Aftermarket:Completionofsale,notforpurposeofresale,fromthemanufacturer.

StateofMassachusetts:Theinstallationmustbemade

byalicensedplumberorgastterintheCommonwealth

of Massachusetts.

TABLE OF CONTENTS

Safety .................................................................. 3

Unpacking............................................................ 4

Introduction.......................................................... 4

Selecting Location ............................................... 5

Product Specications......................................... 6

Pre-Installation Preparation................................. 7

Venting Installation .............................................. 9

Installation ..........................................................11

Operation........................................................... 19

Inspecting Burners ............................................ 20

Cleaning and Maintenance................................ 21

Wiring Diagram.................................................. 22

Replacement Parts............................................ 22

Service Hints ..................................................... 22

Technical Service............................................... 22

Troubleshooting................................................. 23

Parts .................................................................. 26

Accessories ....................................................... 31

Warranty ..............................................Back Cover

www.desatech.com

108795-01V 3

SAFETY

1. This appliance is only for use with the type

of gas indicated on the rating plate. This

appliance is not convertible for use with

other gases unless a certied kit is used.

2. For propane/LP replace, do not place

propane/LP supply tank(s) inside any

structure. Locate propane/LP supply

tank(s) outdoors. To prevent performance

problems, do not use propane/LP fuel tank

of less than 100 lbs. capacity.

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not

use any phone in your building

• immediately call your gas supplier from

a neighbor’s phone. Follow the gas

supplier's instructions

• if you cannot reach you gas supplier, call

the re department.

4. Never install the replace

• in a recreational vehicle

• where curtains, furniture, clothing or

other ammable objects are less than

42" from front, top or sides of replace

• in high trafc areas

• in windy or drafty areas

5. This replace reaches high temperatures.

Keep children and adults away from hot

surfaces to avoid burns or clothing igni-

tion. Fireplace will remain hot for a time

after shutdown. Allow surfaces to cool

before touching.

6. Carefully supervise young children when

they are in the room with replace.

7. A hearth extension is not required with this

appliance. If one is installed, it is for aes-

thetic purposes only and does not have

to meet the standard requirements.

8. Turn replace off and let cool before ser-

vicing or repairing. Only a qualied service

person should install, service or repair

this replace. Have replace inspected

annually by a qualied service person.

9. You must keep control compartments,

burners and circulating air passages clean.

More frequent cleaning may be needed due

to excessive lint and dust from carpeting,

bedding material, etc. Turn off the gas valve

and pilot light before cleaning replace.

10. Have venting system inspected annually by

a qualied service person. If needed, have

venting system cleaned or repaired. See

Cleaning and Maintenance, page 21.

WARNING: This product con-

tainsand/orgenerateschemicals

knowntotheStateofCalifornia

tocausecancerorbirthdefects

orotherreproductiveharm.

IMPORTANT:Readthisowner’s

manualcarefullyandcompletely

before trying to assemble, op-

erate or service this replace.

Improper use of this replace

cancauseseriousinjuryordeath

from burns, re, explosions,

electrical shock and carbon

monoxidepoisoning.

DANGER:Carbonmonoxide

poisoningmayleadtodeath!

This replace is a vented product. This replace

will not produce any gas leakage into your home

if properly installed. This replace must be

properly installed by a qualied service person.

If this unit is not properly installed by a qualied

service person, gas leakage can occur.

CarbonMonoxidePoisoning: Early signs of

carbon monoxide poisoning resemble the u,

with headaches, dizziness or nausea. If you

have these signs, the replace may not have

been installed properly. Getfreshairatonce!

Have replace inspected and serviced by a

qualied service person. Some people are more

affected by carbon monoxide than others. These

include pregnant women, people with heart or

lung disease or anemia, those under the inu-

ence of alcohol and those at high altitudes.

Propane/LP gas and natural gas are both

odorless. An odor-making agent is added

to each of these gases. The odor helps you

detect a gas leak. However, the odor added

to these gases can fade. Gas may be present

even though no odor exists.

Make certain you read and understand all

warnings. Keep this manual for reference. It

is your guide to safe and proper operation of

this replace.

WARNING: Any change to

thisreplaceoritscontrolscan

bedangerous.

www.desatech.com 108795-01V4

11. Keep the area around your fireplace

clear of combustible materials, gasoline

and other ammable vapor and liquids.

Do not run fireplace where these are

used or stored. Do not place items such

as clothing or decorations on or around

replace.

12. Do not use this replace to cook food or

burn paper or other objects.

13. Do not use any solid fuels (wood, coal,

paper, cardboard, etc.) in this replace.

Use only the gas type indicated on re-

place nameplate.

14. This appliance, when installed, must be

electrically grounded in accordance with

local codes or, in the absence of local

codes, with the National Electrical Code,

ANSI/NFPA 70 or the Canadian Electrical

Code, CSA C22.1.

15. Do not obstruct the ow of combustion

and ventilation air in any way. Provide

SAFETY

Continued

INTRODUCTION

adequate clearances around air open-

ings into the combustion chamber along

with adequate accessibility clearance for

servicing and proper operation.

16. Do not install replace directly on carpet-

ing, vinyl tile or any combustible material

other than wood. The replace must set

on a metal or wood panel extending the

full width and depth of the replace.

17. Do not use replace if any part has been

exposed to or under water. Immediately

call a qualied service person to arrange

for replacement of the unit.

18. Do not operate fireplace if any log is

broken.

19. Do not use a blower insert, heat exchang-

er insert or other accessory not approved

for use with this replace.

20. Provide adequate clearances around air

openings.

UNPACKING

The following items are packed inside the

rebox. Remove before positioning rebox

into framing.

• Transition Collar - For vent connection

• Ceramic Log Pack - Shrink-wrapped on

cardboard

• Three (3) plastic bags containing lava rock,

pan and ember materials

• Rear Log - Remove the two plastic quick

ties from around the burner and grate

• Grate Stand - Lift off of burner pan

Check all items for any shipping damage. If

damaged, promptly inform dealer or distributor

where you bought the product.

Safely retain these items for later installation.

Models M36(P)(B,H), VM36(P)(B,H),

M42(P)(B,H) and VM42(P)(B,H) are vented

gas replaces that use a millivolt gas control

valve with a millivolt ignition system. A 6" B-

Type venting system and a listed type vent cap

are not supplied but are required for proper

operation. See venting instructions on pages

9 and 10.

WARNING: This gas appli-

ancemustnotbeconnectedto

achimneyueservicingasolid

fuelburningappliance.

BEFORE YOU BEGIN

Before beginning the installation of your

appliance, read these instructions through

completely.

This DESA Heating, LLC appliance and its

approved components are safe when installed

according to this installation manual and are

operated as recommended by DESA Heating,

LLC. Unless you use DESA Heating, LLC ap-

proved components tested for this appliance,

YOUMAYCAUSEAFIREHAZARD!

The DESA Heating, LLC warranty will be

voided by and DESA Heating, LLC disclaims

any responsibility for the following actions :

A) Modication of the appliance or any of the

components.

B) Use of any component part not approved

by DESA Heating, LLC in combination

with this appliance.

C) Installation and/or operation in a manner

other than instructed in this manual.

Burning of anything other than the type of

gas approved for use in this gas appliance.

www.desatech.com

108795-01V 5

The installation must conform with local codes

or, in the absence of local codes, with the cur-

rent National Fuel Gas Code, ANSI Z223.1/

NFPA 54. This appliance complies with ANSI

Z21.50/CSA 2.22.

WARNING: Installation of

thisapplianceshould bedone

by a qualied service person

well trained in the installation

of such appliances. You will

alsoneedabuildingpermitfrom

your local Building and Safety

Commissionerbeforeinstalling

this appliance; otherwise your

insuranceco.maynotcoverthis

appliance.

NOTICE: This appliance is not

intendedtobeusedasaprimary

source of heat.

INTRODUCTION

Continued

Figure 1 - Possible Locations for

Installing Appliance

INTERNAL WALL

INSTALLATION

CORNER

INSTALLATION

FULL

PROJECTION

INSTALLATION

FLUSH

INSTALLATION

CAUTION: Do not connect

appliancebeforepressuretest-

inggaspiping.Damagetogas

valvemayresultandanunsafe

conditionmaybecaused.

The appliance and it’s individual shutoff valve

must be disconnected from gas supply piping

system during any pressure testing of that

system at test pressures in excess of 1/2

psig (3.5 kPa).

The appliance must be isolated from the gas

supply piping system by closing its individual

manual shutoff valve during any pressure testing

of the gas supply piping system at test pressures

equal to or less than 1/2 psig (3.5 kPa).

For the purpose of input adjustment two

pressure taps (for IN and OUT pressures)

are provided on the gas control valve for test

gauge connections to the appliance.

Flush installations are recommended where

living space is limited or at a premium and

since the space required to enclose the ap-

pliance would be located beyond an outside

wall, this would also reduce the cutting of

joists, roof rafters and such. Check local

codes for any restrictions.

Projected installations can extend any

distance into the room. A projection may

be ideal for a new addition on an existing,

nished wall.

Corner installations make use of space

that may not normally be used and provides

a wider and more efcient range for radiant

heat transference.

Internalwallinstallations provide a discreet

option for room separation and can also be

ideal as an addition to an existing wall.

SELECTING LOCATION

To determine the safest and most efcient

location for your appliance, you must take into

consideration the following guidelines:

1. The location must allow for proper clear-

ances (see Clearances, page 7).

2. Consider a location where heat output

would not be affected by drafts, air con-

ditioning ducts, windows or doors.

3. A location that avoids the cutting of joists

or roof rafters will make installation easier.

Figure 1 shows a plan view of a few com-

mon locations.

www.desatech.com 108795-01V6

PRODUCT SPECIFICATIONS

GAS RATING - NATURAL

M36(B,H),VM36(B,H) M42(B,H),VM42(B,H)

Max. Input Rating: 40,000 Btu/Hr 45,000 Btu/Hr

Manifold Pressure: 3.5" WC (.87 kPa) 3.5" WC (.87 kPa)

Minimum Supply Pressure: 4.5" WC (1.12 kPa) 4.5" WC (1.12 kPa)

Maximum Supply Pressure: 10.5" WC (2.66 kPa) 10.5" WC (2.66 kPa)

Orice Size: # 30 # 29

GAS RATING - PROPANE/LP

M36P(B,H),VM36P(B,H) M42P(B,H),VM42P(B,H)

Max. Input Rating: 40,000 Btu/Hr 45,000 Btu/Hr

Manifold Pressure: 10" WC (2.49 kPa) 10" WC (2.49 kPa)

Minimum Supply Pressure: 11" WC (2.74 kPa) 11" WC (2.74 kPa)

Maximum Supply Pressure: 13" WC (3.23 kPa) 13" WC (3.23 kPa)

Orice Size: # 52 # 51

Outside Air

Kit Location

(Optional)

13.5"

1.5"

Glass Door

(Optional)

Alternate Gas

Supply Inlet

Stand Off

Collar

For Use With

6"Ø Type B-1

Ve nt Pipe Only

DIMENSIONS

HEARTH AREA

Figure 2 - Appliance Dimensions

Model 36 Model 42 Model 36 Model 42 Model 36 Model 42

A 29" 36" I 40 1/4" 44 1/4" Q 13 7/8" 14"

B5/8" 5/8" J 21" 24" R 10 1/2" 12 1/2"

C 41" 48" K 8" 9" S 2 1/2" 2 1/2"

D 12" 14" L 34 3/4" 42" T 8 1/8" 8 1/8"

E 21 1/4" 23" M 42" 49" U 11" 12 3/4"

F 22 1/4" (24" w/o Brick) 29 1/4" (31" w/o Brick) N 36" 40" V 7" 7"

G32 5/8" (34" w/o Brick) 39 1/2" (41 1/4" w/o Brick) O 37" 41" W 2 1/4" 2 1/4"

H 15 3/4" (16 3/4" w/o Brick) 17 3/4" (18 3/4" w/o Brick) P 8 5/8" 10 1/2" X 5" 4 1/2"

www.desatech.com

108795-01V 7

PRE-INSTALLATION PREPARATION

Figure 3 - Minimum Clearances

(Top View)

0" Clearance

Nailing

Flange

Front Face

Left Side

Surround

Back

Drywall

2 x 4 Stud

Figure 4 - Minimum Clearances

(Front View)

42" (106.7 cm)

Min. Clearance

from Opening to

Ceiling 0" Clearance

Ceiling

1" (2.5 cm)

Min. Clearance

to "B" Vent's

Outer Pipe

Maintain 2" (5.1 cm)

Min. Clearance to

Transition Pipe as

Measured at Outer

Ve nt Collar

Required air

spaces are

indicated with

an "

". Do not

pack with

insulation or

any other

material.

DO NOT BLOCK

OR OBSTRUCT

OPENINGS

0" Clearance to

Combustible or

Noncombustible

Flooring

MANTEL CLEARANCES AND WALL

DETAILS

A combustible mantle shelf maybe installed

a maximum 12" (22.9 cm) from the wall.

Figures 5 and 6 show the minimum allow-

able distances from various combustible

mantle components in relation to fireplace

opening.

Spacer

3" (7.6 cm)

(3.8 cm) Max.

6" (15.2 cm)

12"

(22.9 cm)

Combustible

Materials

Header

Figure 5 - Mantel Clearances - Side View

(Cross Section)

M36(B,H),

M36P(B,H)

VM36(B,H),

VM36P(B,H)

M42(B,H),

M42P(B,H)

VM42(B,H),

VM42P(B,H)

A14" (35.6 cm) 15" (38 cm)

B 8" (20.3 cm) 9" (22.9 cm)

(3.8 cm)

Max. 3" (7.6 cm)

Max.

6" (15.2 cm)

Max. A

Outer Surround Combustible

Material May

Be Used

TOP VIEW

SAFE

ZONE

Perpendicular

Wall

Figure 6 - Side Clearances - Top View

(Cross Section)

CLEARANCES

Minimum clearances to combustibles are:

Back and Sides of Outer Surround 0" min.

Drywall to Sides of Front Face

(Nailing Flanges) 0" min.

“B” Vent Surfaces 1" min.

Ceiling to Opening 42" min.

Floor 0" min.

Perpendicular Wall See Figure 6

 CAUTION: Do not block

required air spaces with insu-

lationoranyothermaterial.Do

not obstruct effective opening

of appliance with any type of

facingmaterial.

M36(B,H),

M36P(B,H)

VM36(B,H),

VM36P(B,H)

M42(B,H),

M42P(B,H)

VM42(B,H),

VM42P(B,H)

A9" (22.9 cm) 6" (15.2 cm)

B 12" (30.5 cm) 9" (22.9 cm)

www.desatech.com 108795-01V8

PRE-INSTALLATION PREPARATION

Continued

FRAMING

1. Frame appliance enclosure as illustrated

in Figures 7 and 8.

Note: If a wall covering is used to line the

enclosure, then all measurements must

be from the surface of the covering.

2. Place the appliance into the framing and

secure it.

Note: If appliance is to be raised above

oor level, a platform must be built to

support the appliance.

3. Install the supply line to the appliance

using a 1/2" NPT black iron gas line ter-

minating 2 5/16" above the bottom of the

appliance. The gas line must be installed

through the lower left side access point or

alternate access hole in the bottom of the

appliance (see Figure 19, page 13).

4. Repack insulation around the gas line to

cover any remaining openings in the con-

duit sleeve. Prepare the incoming gas line

with teon tape or pipe joint compound

and hook-up incoming gas line to the

exible gas line.

Note: If 1/2" NPT black iron pipe does not

mate with tting at the end of exible gas

line, remove tting and replace with a 37°

are 3/4"-12, 1/2" NPT (female) tting.

 WARNING: When nishing

appliance,donotoverlapcom-

bustiblematerialontotheblack

front face. Brick, tile or other

noncombustiblematerialsmay

beappliedtothefaceprovided

that any gap is between the

material used and the face is

caulkedwithanoncombustible

caulking.

Figure 7 - Rough Opening for Installing

in Wall

M36(B,H),

M36P(B,H)

VM36(B,H),

VM36P(B,H)

M42(B,H),

M42P(B,H)

VM42(B,H),

VM42P(B,H)

A 40 3/8" (102 cm) 44 3/8" (112 cm)

B21 3/8" (54.3 cm) 23 1/8" (58.7 cm)

C 41 1/4" (104.8 cm) 48 1/4" (122.6 cm)

Figure 8 - Corner Installation Guidelines

M36(B,H),

M36P(B,H)

VM36(B,H),

VM36P(B,H)

M42(B,H),

M42P(B,H)

VM42(B,H),

VM42P(B,H)

A 24 1/2" (62.2 cm) 27 9/16" (70 cm)

B73 7/8" (187.6 cm) 83 7/8" (213 cm)

C 52 3/16" (132.6 cm) 59 5/16" (150.6 cm)

D 17 1/4" (43.8 cm) 19 1/2" (49.5 cm)

These Dimensions Allow for a 3/4"

Clearance at Sides and Back of Fireplace.

However, 0" Clearance is Permitted.

3/4" Clearance Not Required

at Nailing Flanges

www.desatech.com

108795-01V 9

INSTALLING TRANSITION PIPE AND

STARTER COLLAR

The transition pipe and starter collar shown

in Figure 9 are supplied with the replace,

unattached and ready for installation. Re-

move starter collar and set aside. Slide

transition pipe over vent collar and attach

with a minimum of three screws. Replace

starter collar over transition pipe and attach

using four screws located on leg stands (ve

used on model M42). To install B-vent piping,

slide the rst piece of B-vent over transition

pipe and attach with either a minimum of two

screws or other means approved by the vent

manufacturer. Figure 9 - Installing Transition Pipe and

Starter Collar

B-Vent Piping

Transition Pipe

Starter Collar

Vent Collar

PRE-INSTALLATION PREPARATION

Continued

VENTING INSTALLATION

60° or greater. The total vertical height in this

example represents the minimum height of 8

feet and therefore the allowable lateral is 6

feet when the 75% rule applies. If the lateral

length must exceed 75% then the system

must be sized in accordance with Category I

venting tables.

Example2: Shows a multiple offset each at

45° of inclination. Multiple offsets are permit-

ted if they do not exceed 45° of inclination. The

total lengths of the two offsets are not required

to meet the 75% allowable rule.

Example3:Shows a single offset at 45° of

inclination and therefore the lateral length at

10 feet of offset does not have to meet the

75% rule.

In each case the offsets must be supported

and restops must be positioned wherever

the vent must pass through a sub-oor, ceil-

ing joist or an attic overhang. The vent pipe

must terminate vertically into a listed type vent

cap and extend a sufcient height through

an approved roof ashing, roof jack or a roof

thimble. At all points listed clearances must

be maintained.

Vent terminations must be located in ac-

cordance with height and proximity rules of

NFPA No. 54. These rules apply to vents at

12" diameter or less and require a minimum

height in accordance with the roof pitch and a

minimum of 8 ft. distance from a vertical wall

or obstruction (see Figure 11, page 10).

A B-type venting system must be connected

to the appliance for venting to the outside of

the building.

The following section is provided as a guide

to a standard B-type vent installation.

Standing codes requirements concerning B-

type vent installations may vary within your

state, province or local codes jurisdiction.

Therefore, it is recommended that you check

with your local building codes for specic

requirements or in absence of local codes,

follow Section 7.0 of the current National Fuel

Gas Code ANSI Z223.1/NFPA 54.

This gas appliance must be vented to the

outdoors only and may not be terminated into

an attic space or into a chimney ue servicing

a solid fuel burning appliance.

This appliance may be vented through a

manufactured chimney system or a masonry

chimney using a B-vent adapter or a chim-

ney liner system if all are listed, inspected

and approved by local codes and/or building

authorities.

The examples shown in Figure 10, page 10

are typical of most B-vent installations and

codes practices.

Example1: Shows the minimum allowable

system height and lateral offset for a 60° or

greater inclination. Code species that offsets

at 60° or greater are considered horizontal

and must follow the 75% rule for lateral to

total vertical system height. Codes also allow

only one offset in the total system when at

www.desatech.com 108795-01V10

Maintain

Listed

Clearance

Maintain

Listed

Clearance

12' Min.

12' Min. 45°

45°

12' Min.

60° 45°

Position

Firestop

Position

Firestop

Position

Firestop

Listed

Vent Cap

Listed

Vent Cap

Listed

Vent Cap

Maintain

Listed

Clearance

Maintain

Listed

Clearance

Maintain

Listed

Clearance

Maintain

Listed

Clearance

Support Each

Lateral At

Least Every

6 Feet

Maintain

Listed

Clearance

10'

EXAMPLE 3EXAMPLE 2

EXAMPLE 1

Figure 10 - Typical B-Vent Conguration

VENTING INSTALLATION

Continued

Some codes areas allow the use of existing

B-type vent systems if the system is at or

above the recommended diameter of the ue,

in this case 6".

The ue connection must be made using

listed B-type connectors and the existing

system must be code inspected for damage

and proper installation.

It is not recommended that this appliance be

common vented with an existing gas burning

appliance.

Note: Before connecting this appliance to an

existing vent system consult with your local

architect, planner or building ofcial.

WARNING: This appliance

must be properly connected

to a system and must not be

connected to a chimney ue

servicing a separate solid fuel

burningappliance.

Lowest

Discharge

Opening

Listed

Ve nt Cap

8 Ft. Min.

Roof Pitch x/12

Listed Clearance

Listed

Gas

Ve nt

H (Min)

Height

From Roof

Roof Pitch

H(Min.)

Feet Meter

Flat to 6/12 1.0 ax 0.30

6/12 to 7/12 1.25 0.38

Over 7/12 to 8/12 1.5 0.46

Over 8/12 to 9/12 2.0 0.61

Over 9/12 to 10/12 2.5 0.76

Over 10/12 to 11/12 3.25 0.99

Over 11/12 to 12/12 4.0 1.22

Over 12/12 to 14/12 5.0 1.52

Over 14/12 to 16/12 6.0 1.83

Over 16/12 to 18/12 7.0 2.13

Over 18/12 to 20/12 7.5 2.27

Over 20/12 to 21/12 8.0 2.44

Figure 11 - B-Vent Terminations

This manual suits for next models

Table of contents

Other Desa Indoor Fireplace manuals

Desa

Desa O36NRA Quick start guide

Desa

Desa CGMFN Quick start guide

Desa

Desa CGEFP33PRB Quick start guide

Desa

Desa MSVFBNR Series Quick start guide

Desa

Desa CGCFTN Quick start guide

Desa

Desa PN36-A Safety guide

Desa

Desa VYGF33PRC Quick start guide

Desa

Desa CWC42C User manual

Desa

Desa Comfort Glow CGFB32CA Original instructions

Desa

Desa VVC36PE Series Quick start guide

Desa

Desa VICTORIAN V36EN-A Series Quick start guide

Desa

Desa VTGF33PRA Quick start guide

Desa

Desa Design Dynamics VTD-18N-BTB Quick start guide

Desa

Desa Vanguard VVSR18 Quick start guide

Desa

Desa Comfort Glow CGEFP33PR Quick start guide

Desa

Desa VT32N Series Quick start guide

Desa

Desa Comfort Glow CGCF26TN Quick start guide

Desa

Desa (V)GM36 User manual

Desa

Desa CFFP18NT Quick start guide

Desa

Desa VTC36N Series Quick start guide

Desa

Desa V36N SERIES Quick start guide

Desa

Desa DCFTNA Quick start guide

Desa

Desa FPVF33PR Quick start guide

Desa

Desa GMC55FA Instruction manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Miles Industries

Miles Industries Vogue 1300IRN Installation & operating instructions