Desa CGEFP33NRC Quick start guide

For more information, visit www.desatech.com

WARNING: If the information in this manual is not

followed exactly, a re or explosion may result causing

property damage, personal injury or loss of life.

— Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re

department.

— Installation and service must be performed by a quali-

ed installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

UNVENTED (VENT-FREE) GAS FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

CGEFP33NRC, CGEFP33PRC, LMFP33NRC AND LMFP33PRC

REMOTE CONTROL GAS FIREPLACE SYSTEMS

Patent Pending

Shown with

optional cabinet

mantel and hearth

base accessories.

www.desatech.com 121308-01E2

SAFETY

WARNING: Improper

installation, adjustment,

alteration, service or

maintenance can cause

injury or property dam-

age. Refer to this manual

for correct installation

and operational proce-

dures. For assistance or

additional information

consult a qualified in-

staller, service agency or

the gas supplier.

WARNING: This is an

unvented gas-red heat-

er. It uses air (oxygen)

from the room in which

it is installed. Provisions

for adequate combustion

and ventilation air must

be provided. Refer to Air

for Combustion and Ven-

tilation section on page 5

of this manual.

This appliance may be in-

stalled in an aftermarket,*

permanently located,

manufactured (mobile)

home, where not prohib-

ited by local codes.

This appliance is only for

use with the type of gas

indicated on the rating

plate. This appliance is

not convertible for use

with other gases.

* Aftermarket: Completion of sale, not for

purpose of resale, from the manufacturer

WARNING: This product

contains and/or generates

chemicals known to the State

of California to cause cancer or

birth defects or other reproduc-

tive harm.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble,

operate or service this heater.

Improper use of this heater can

cause serious injury or death

from burns, fire, explosion,

electrical shock and carbon

monoxide poisoning.

TABLE OF CONTENTS

Safety .................................................................. 2

Product identication ........................................... 4

Local Codes......................................................... 4

Unpacking............................................................ 5

Product Features................................................. 5

Air for Combustion and Ventilation ...................... 5

Installation ........................................................... 8

Operation........................................................... 20

Inspecting Burners............................................. 24

Cleaning and Maintenance................................ 25

Troubleshooting................................................. 26

Specications .................................................... 30

Wiring Diagram.................................................. 30

Technical Service............................................... 30

Replacement Parts............................................ 30

Service Hints ..................................................... 30

Accessories ....................................................... 31

Parts .................................................................. 32

Warranty ..............................................Back Cover

www.desatech.com

121308-01E 3

Do not place clothing or other

ammable material on or near

the appliance. Never place any

objects on the heater.

Fireplace and screen become

very hot when running replace.

Keep children and adults away

from hot surfaces to avoid burns

or clothing ignition. Fireplace

will remain hot for a time after

shutdown. Allow surfaces to

cool before touching.

Carefully supervise young chil-

dren when they are in the room

with replace. When using the

optional hand-held remote ac-

cessory, keep selector switch

in the OFF position to prevent

children from turning on burners

with remote.

You must operate this replace

with the replace screen and

hood in place. Make sure re-

place screen and hood are in

place before running heater.

Keep the appliance area clear

and free from combustible ma-

terials, gasoline and other am-

mable vapors and liquids.

1. This appliance is only for use with the type

of gas indicated on the rating plate. This

appliance is not convertible for use with

other gases.

2. Do not place propane/LP supply tank(s)

inside any structure. Locate propane/LP

supply tank(s) outdoors (propane/LP

units only).

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not

use any phone in your building

• immediately call your gas supplier from

a neighbor’s phone. Follow the gas

supplier’s instructions

• if you cannot reach your gas supplier,

call the re department

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs

of carbon monoxide poisoning resemble the

u, with headaches, dizziness or nausea. If

you have these signs, the heater may not be

working properly. Get fresh air at once! Have

heater serviced. Some people are more af-

fected by carbon monoxide than others. These

include pregnant women, people with heart or

lung disease or anemia, those under the inu-

ence of alcohol and those at high altitudes.

Natural and Propane/LP Gas: Natural and

propane/LP gases are odorless. An odor-

making agent is added to the gas. The odor

helps you detect a gas leak. However, the

odor added to the gas can fade. Gas may be

present even though no odor exists.

Make certain you read and understand all

warnings. Keep this manual for reference. It

is your guide to safe and proper operation of

this heater.

WARNING: Any change to

this heater or its controls can

be dangerous.

WARNING: Do not allow fans

to blow directly into the replace.

Avoid any drafts that alter burner

ame patterns. Ceiling fans can

create drafts that alter burner

ame patterns. Altered burner

patterns can cause sooting.

WARNING: Do not use a

blower insert, heat exchanger

insert or other accessory not ap-

proved for use with this heater.

Due to high temperatures, the

appliance should be located out

of trafc and away from furniture

and draperies.

SAFETY

Continued

www.desatech.com 121308-01E4

SAFETY

Continued

4. This replace shall not be installed in a

bedroom or bathroom.

5. Do not use this replace as a wood-burn-

ing replace. Use only the logs provided

with the replace.

6. Do not add extra logs or ornaments such

as pine cones, vermiculite or rock wool.

Using these added items can cause soot-

ing. Do not add lava rock around base.

Rock and debris could fall into the control

area of replace.

To prevent the creation of soot, follow the

instructions in Cleaning and Maintenance,

page 25.

8. Before using furniture polish, wax, carpet

cleaner or similar products, turn heater off. If

heated, the vapors from these products may

create a white powder residue within burner

box or on adjacent walls or furniture.

9. This replace needs fresh air ventilation to

run properly. This replace has an Oxygen

Depletion Sensing (ODS) safety shutoff

system. The ODS shuts down the re-

place if enough fresh air is not available.

See Air for Combustion and Ventilation,

page 5. If replace keeps shutting off, see

Troubleshooting, page 26.

10. Do not run replace

• where ammable liquids or vapors are

used or stored

• under dusty conditions

11. Do not use this replace to cook food or

burn paper or other objects.

12. Do not use replace if any part has been

exposed to or under water. Immediately

call a qualied service technician to inspect

the replace and to replace any part of the

control system and any gas control which

has been under water.

13. Do not operate fireplace if any log is

broken. Do not operate replace if a log

is chipped (dime-sized or larger).

14. Turn fireplace off and let cool before

servicing. Only a qualied service person

should service and repair replace.

15. Operating replace above elevations of

4,500 feet could cause pilot outage.

16. To prevent performance problems in

propane/LP units, do not use propane/LP

fuel tanks of less than 100 lbs. capacity

(propane/LP units only).

17. Provide adequate clearances around air

openings.

Figure 2 - Fireplace

Figure 1 - Log Base Assembly

(LMFP33PR Shown)

4-Piece

Log Set

Remote Receiver

Piezo

Ignitor

Remote Control

Control

Knob

Top Louver

Assembly

Firebox

Hood

Bottom Louver Assembly

Screen

Assembly

Top Outer Casing

Firebox

Support

Blower

Assembly

(Optional)

LOCAL CODES

Install and use replace with care. Follow all

local codes. In the absence of local codes,

use the latest edition of The National Fuel

Gas Code ANSI Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

Note: Where listed vented decorative logs

are required, thermostat operation is not

permitted.

PRODUCT

IDENTIFICATION

www.desatech.com

121308-01E 5

UNPACKING

CAUTION: Do not remove the

data plates attached to the heater

base assembly. The data plates

contain important warranty and

safety information.

1. With utility knife, cut the carton all the way

around above the staples on the bottom

tray. Lift the carton off the heater. Remove

packing. Note: The hood is located in the

packing on the right hand side of the heater

front. Lift the heater off the bottom tray.

2. Locate two screws above top corners of

the replace screen. Remove and discard

these screws. Lift replace screen up and

pull out to remove.

3. Remove protective packaging applied to

logs, log base assembly and replace.

4. Remove replace hood from carton insert.

5. Check heater for any shipping damage.

If heater is damaged call DESA Heating,

LLC at 1-866-672-6040 for replacement

parts before returning to dealer.

PRODUCT FEATURES

OPERATION

This vent-free replace is clean burning. It

requires no outside venting. There is no heat

loss out a vent or up a chimney. Heat is gen-

erated by both realistic ames. When used

without the blower, the replace requires no

electricity making it ideal for emergency back-

up heat. This heater is designed for vent-free

operation. It has been tested and approved to

ANSI Z21.11.2 standard for unvented heaters.

State and local codes in some areas prohibit

the use of vent-free heaters.

LOCAL CODES

Continued

State of Massachusetts: The installation

must be made by a licensed plumber or

gas tter in the Commonwealth of Mas-

sachusetts.

Sellers of unvented propane or natural

gas-fired supplemental room heaters

shall provide to each purchaser a copy of

527 CMR 30 upon sale of the unit.

Vent-free gas products are prohibited for

bedroom and bathroom installation in the

Commonwealth of Massachusetts.

SAFETY DEVICE

This replace has a pilot with an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The

ODS/pilot is a required feature for vent-free

room heaters. The ODS/pilot system shuts off

the replace if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This replace has a piezo ignitor. This sys-

tem requires no matches, batteries or other

sources to light replace.

OPTIONAL BLOWER ASSEMBLY

(GA3750 SERIES & GA3650TB

SERIES)

This replace accepts an optional blower as-

sembly (not included). The GA3650TB Series

blower operates thermostatically and features

a variable speed control. The GA3750 Series

blower operates manually and also features a

variable speed control. The blower circulates

heated air from the replace into the room.

See Accessories, page 31

AIR FOR COMBUSTION

AND VENTILATION

WARNING: This heater shall

not be installed in a room or

space unless the required vol-

ume of indoor combustion air

is provided by the method de-

scribed in the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, the

International Fuel Gas Code, or

applicable local codes. Read the

following instructions to insure

proper fresh air for this and

other fuel-burning appliances

in your home.

Today’s homes are built more energy efcient

than ever. New materials, increased insulation

and new construction methods help reduce

heat loss in homes. Home owners weather

strip and caulk around windows and doors to

keep the cold air out and the warm air in. Dur-

ing heating months, home owners want their

homes as airtight as possible.

While it is good to make your home energy

efcient, your home needs to breathe. Fresh

air must enter your home. All fuel-burning ap-

pliances need fresh air for proper combustion

and ventilation.

www.desatech.com 121308-01E6

whose volume is less than 50 cubic feet per

1,000 Btu per hour (4.8 m

per kw) of the ag-

gregate input rating of all appliances installed

in that space and an unconned space as a

space whose volume is not less than 50 cubic

feet per 1,000 Btu per hour (4.8 m

per kw) of

the aggregate input rating of all appliances

installed in that space. Rooms communicating

directly with the space in which the appliances

are installed*, through openings not furnished

with doors, are considered a part of the un-

conned space.

* Adjoining rooms are communicating only if

there are doorless passageways or ventilation

grills between them.

DETERMINING FRESH-AIR FLOW

FOR FIREPLACE LOCATION

Determining if You Have a Conned or

Unconned Space

Use this work sheet to determine if you have

a conned or unconned space.

Space: Includes the room in which you will

install replace plus any adjoining rooms with

doorless passageways or ventilation grills be-

tween the rooms.

1. Determine the volume of the space (length

x width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example: Space size 20 ft. (length) x 16 ft.

(width) x 8 ft. (ceiling height) = 2,560 cu. ft.

(volume of space)

If additional ventilation to adjoining room

is supplied with grills or openings, add the

volume of these rooms to the total volume

of the space.

2. Multiply the space volume by 20 to determine

the maximum Btu/Hr the space can support.

________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example: 2,560 cu. ft. (volume of space) x

20 = 51,200 (maximum Btu/Hr the space can

support)

3. Add the Btu/Hr of all fuel burning appliances

in the space.

Vent-free replace _________ Btu/Hr

Gas water heater* _________ Btu/Hr

Gas furnace _________ Btu/Hr

Vented gas heater _________ Btu/Hr

Gas replace logs _________ Btu/Hr

Other gas appliances* + ________ Btu/Hr

Total =________ Btu/Hr

* Do not include direct-vent gas appliances.

AIR FOR COMBUSTION

AND VENTILATION

Continued

Exhaust fans, replaces, clothes dryers and

fuel burning appliances draw air from the house

to operate. You must provide adequate fresh

air for these appliances. This will insure proper

venting of vented fuel-burning appliances.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Air for

Combustion and Ventilation.

All spaces in homes fall into one of the three

following ventilation classications:

1. Unusually Tight Construction

2. Unconned Space

3. Conned Space

The information on pages 5 through 7 will

help you classify your space and provide

adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and windows

may provide enough fresh air for combustion

and ventilation. However, in buildings of un-

usually tight construction, you must provide

additional fresh air.

Unusually tight construction is dened as

construction where:

a. walls and ceilings exposed to the out-

side atmosphere have a continuous

water vapor retarder with a rating of one

perm (6 x 10-11 kg per pa-sec-m2) or less

with openings gasketed or sealed and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to areas

such as joints around window and door

frames, between sole plates and oors,

between wall-ceiling joints, between

wall panels, at penetrations for plumb-

ing, electrical and gas lines and at other

openings.

If your home meets all of the three criteria

above, you must provide additional fresh air.

See Ventilation Air From Outdoors, page 7.

If your home does not meet all of the three cri-

teria above, proceed to Determining Fresh-Air

Flow For Heater Location.

Conned and Unconned Space

The National Fuel Gas Code, ANSI Z223.1/

NFPA 54 denes a conned space as a space

www.desatech.com

121308-01E 7

AIR FOR COMBUSTION

AND VENTILATION

Continued

Figure 4 - Ventilation Air from Outdoors

Figure 3 - Ventilation Air from Inside

Building

Outlet

Air

V e ntilated

Attic

Outlet

Air

Inlet

Air

Inlet Air V e ntilated

Crawl Space

T o

Crawl

Space

T o Attic

Remove

Door into

Adjoining

Room,

Option

V e ntilation Grills

Into Adjoining Room,

Option 2

V e ntilation

Grills

Into Adjoining

Room,

Option 1

12"

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining

unconned space. When ventilating to an

adjoining unconned space, you must provide

two permanent openings: one within 12" of the

ceiling and one within 12" of the oor on the

wall connecting the two spaces (see options

1 and 2, Figure 3). You can also remove door

into adjoining room (see option 3, Figure 3).

Follow the National Fuel Gas Code, ANSI

Z223.1/NFPA 54, Air for Combustion and

Ventilation for required size of ventilation

grills or ducts.

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation

grills or ducts. You must provide two perma-

nent openings: one within 12" of the ceiling

and one within 12" of the oor. Connect these

items directly to the outdoors or spaces open

to the outdoors. These spaces include attics

and crawl spaces. Follow the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Air for

Combustion and Ventilation for required size

of ventilation grills or ducts.

IMPORTANT: Do not provide openings for

inlet or outlet air into attic if attic has a thermo-

stat-controlled power vent. Heated air entering

the attic will activate the power vent.

Direct-vent draws combustion air from the

outdoors and vents to the outdoors.

Example:

Gas water heater _________ Btu/Hr

Vent-free replace + ________ Btu/Hr

Total = ________ Btu/Hr

4. Compare the maximum Btu/Hr the space can

support with the actual amount of Btu/Hr used.

_______ Btu/Hr (maximum the space can

support)

_______ Btu/Hr (actual amount of Btu/Hr

used)

Example: 51,200 Btu/Hr (maximum the

space can support)

73,000 Btu/Hr (actual amount of

Btu/Hr used)

The space in the example is a conned space

because the actual Btu/Hr used is more than the

maximum Btu/Hr the space can support. You

must provide additional fresh air. Your options

are as follows:

A. Rework worksheet, adding the space of an

adjoining room. If the extra space provides an

unconned space, remove door to adjoining

room or add ventilation grills between rooms.

See Ventilation Air From Inside Building.

B. Vent room directly to the outdoors. See

Ventilation Air From Outdoors.

C. Install a lower Btu/Hr replace, if lower Btu/

Hr size makes room unconned.

If the actual Btu/Hr used is less than the maxi-

mum Btu/Hr the space can support, the space is

an unconned space. You will need no additional

fresh air ventilation.

WARNING:Iftheareain which

the heater may be operated does

not meet the required volume for

indoor combustion air, combus-

tion and ventilation air shall be

provided by one of the methods

described in the National Fuel

Gas Code,ANSI Z223.1/NFPA 54,

the International Fuel Gas Code,

or applicable local codes.

40,000

33,000

73,000

www.desatech.com 121308-01E8

INSTALLATION

NOTICE: This heater is intended

for use as supplemental heat.

Use this heater along with your

primary heating system. Do not

install this heater as your pri-

mary heat source. If you have a

central heating system, you may

run system’s circulating blower

while using heater. This will help

circulate the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

WARNING: A qualied ser-

vice person must install re-

place. Follow all local codes.

WARNING: Never install the

replace

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing or other ammable

objects are less than 36"

from the front and 42" top of

replace. For side clearances

see Figure 8, page 9

• in high trafc areas

• in windy or drafty areas

CAUTION: This replace cre-

ates warm air currents. These

currents move heat to wall sur-

faces next to replace. Installing

replace next to vinyl or cloth

wall coverings or operating

heater where impurities (such

as, but not limited to, tobacco

smoke, aromatic candles, clean-

ing uids, oil or kerosene lamps,

etc.) in the air exist, may discolor

walls or cause odors.

Note: Your replace is designed to be used in

zero clearance installations. Wall or framing

material can be placed directly against any

exterior surface on the rear, sides or top of

your replace, except where standoff spacers

are integrally attached. If standoff spacers

are attached to your replace, these spacers

can be placed directly against wall or framing

materials.

Use the dimensions shown for rough openings

to create the easiest installation. See Built-In

Fireplace Installation, page 11.

IMPORTANT: Vent-free heaters add moisture

to the air. Although this is benecial, installing

replace in rooms without enough ventilation

air may cause mildew to form from too much

moisture. See Air for Combustion and Venti-

lation, page 5. IMPORTANT: Make sure the

replace is level. If replace is not level, log

set will not work properly.

CHECK GAS TYPE

Use the correct gas type (natural or pro-

pane/LP) for your fireplace. If your gas

supply is not correct, do not install replace.

Call dealer where you bought replace for

proper type replace.

WARNING: This appliance is

equipped for either natural gas

or propane/LP gas but not both.

Gas type is indicated on the rat-

ing plate. Field conversion is not

permitted.

ELECTRICAL HOOKUP

(Models GA3750 Series and GA3650TB

Series Blower Accessories and GA3555

Internal Duplex Kit)

This replace accepts a blower assembly

with an electrical cord. The electrical cord is

ve feet in length. You must locate replace

within reach of a 120 volt grounded electrical

outlet. If not, you must install an electrical

outlet within reach of replace power cord.

The GA3555 outlet accessory is used for

built-in applications with blower accessory

installed.

INSTALLING HOOD

Install hood to top of rebox as shown in

Figure 5, page 9. Use 3 Phillips screws

provided.

www.desatech.com

121308-01E 9

MINIMUM CLEARANCE TO

COMBUSTIBLE MATERIALS

Top 42"; Left and Bottom 16"; Right Side

and Rear 0"; Front 36"

Figure 5 - Installing Hood to Firebox

Figure 6 - Assembling Trim

Side Trim

Slot

Mitered

Edge

Slot

Shim

Set Screws

Adjusting

Plate

Trim

Hanging

Screws

Assembled

Trim

Hanging

Notches

on Trim

Top Trim

INSTALLATION

Continued

Figure 7 - Attaching Trim to Fireplace

Example

Figure 8 - Minimum Clearance for

Combustible to Wall

*Minimum 16" from Side Wall

ASSEMBLING AND ATTACHING

BLACK TRIM

IMPORTANT: If you are recessing the rebox

in a wall, do not attach trim at this time. See

page 11.

Note: The instructions below show assem-

bling and attaching trim to replace.

1. Remove packaging from 3 pieces of trim.

2. Locate 4 brass screws, 2 adjusting plates

with set screws and 2 shims in the hard-

ware packet.

3. Align shim under adjusting plate as shown

in Figure 6.

4. Slide one end of adjusting plate/shim

in slot on mitered edge of top trim (see

Figure 6).

5. Slide other end of adjusting plate/shim

in slot on mitered edge of side trim (see

Figure 6).

6. While firmly holding edges of trim to-

gether, tighten both set screws on the

adjusting plate with slotted screwdriver.

7. Repeat steps 1 through 6 for other side.

8. Tighten trim hanging screws (#10 x 6.25

shoulder) into holes in cabinets. Place as-

sembled trim onto replace cabinet. Align

hanging notches on trim with hanging

screws on side of replace (see Figure 7).

Push trim rmly into place, sliding hanging

notches over hanging screws.

INSTALLATION CLEARANCES

WARNING: Maintain the

minimum clearances. If you can,

provide greater clearances from

oor, ceiling and adjoining wall.

Carefully follow the instructions below. This

will ensure safe installation.

Minimum Clearances For Side

Combustible Material, Side Wall and

Ceiling

A. Clearances from the side of the replace

cabinet to any combustible material and

wall should follow diagram in Figure 8.

Example: The face of a mantel, bookshelf,

etc. is made of combustible material and

protrudes 3 1/2" from the wall. This com-

bustible material must be 4" from the side

of the replace opening (see Figure 8).

Clearances from the top of the replace

opening to the ceiling should not be less

than 42".

www.desatech.com 121308-01E10

CONVENTIONAL FIREPLACE

INSTALLATION

Conventional installation of this fireplace

involves installing replace along with the

corner, face or cabinet mantel with hearth

base accessories against a wall in your home.

Follow the instructions below to install the

replace in this manner.

Note: The instructions in this section show instal-

lation using the cabinet mantel and hearth base

accessories. The hearth base accessory shown

is optional for this installation. You can install re-

place and cabinet mantel directly on the oor.

1. Assemble cabinet mantel, hearth base

and trim accessories. Assembly instruc-

tions are included with each accessory.

2. When installing blower, install a properly

grounded, 120 volt three-prong electrical

outlet at replace location if an outlet is not

there. If possible, locate outlet so cabinet

mantel will cover it when installed (see

Figure 9).

3. Install gas piping to replace location. This

installation includes an approved exible

gas line (if allowed by local codes) after

the equipment shutoff valve. The exible

gas line must be the last item installed on

the gas piping. See Installing Gas Piping

to Fireplace Location, page 13.

Place hearth base accessory against wall at

installation location. Cut an access hole in

hearth top to run exible gas line to replace

(see Figure 9). Make sure to locate access

hole so cabinet mantel will cover it when

installed. Note: You can secure base to oor

using wood screws. Countersink screw

heads and putty over.

5. Route exible gas line through access

hole in hearth base.

Center cabinet mantel on hearth base

(see Figure 10). Make sure mantel is ush

against wall.

INSTALLATION

Continued

7. Break off nailing anges (see Figure 11)

with hammer or pliers.

8. Place cardboard or other protective mate-

rial on top of hearth base. Carefully set

replace on protective material, with back

of replace inside mantel opening.

9. Attach exible gas line from replace gas

regulator to gas supply. See Connecting

Fireplace to Gas Supply, page 15.

10.

If blower is installed, route blower electrical

cord through access holes in either side of

replace. Note: Bushing may be moved if

necessary. Plug electrical cord into electrical

outlet.

11.

Carefully insert replace into cabinet man-

tel. Be careful not to scratch or damage

hearth base or cabinet mantel. Remove

protective material from top of hearth base

and from front of replace (if any).

Note: You can secure replace to hearth

or oor. Open lower louver. Locate screw

holes in bottom of base. Tighten wood

screws through these holes and into hearth

or oor.

12. Check all gas connections for leaks. See

Checking Gas Connections, page 16.

Figure 10 - Installing Cabinet Mantel

Cabinet

Mantel

Figure 11 - Location of Nailing Flanges

Nailing

Flanges

Electrical Outlet

Rigid Gas Line

Gas Line

Access

Hole

Figure 9 - Placing Hearth Base

Accessory Against Wall

Hearth

Base

This manual suits for next models

Table of contents

Other Desa Indoor Fireplace manuals

Desa

Desa (V)V36N-B SERIES Quick start guide

Desa

Desa VKC36PE Series Quick start guide

Desa

Desa VVC36NE Series Quick start guide

Desa

Desa B36L-MC Quick start guide

Desa

Desa Vanguard VI33NRB Quick start guide

Desa

Desa VTGF33PRA Quick start guide

Desa

Desa (V)DVF36TCRP(E) Quick start guide

Desa

Desa VsGF28nTF Quick start guide

Desa

Desa MSBVBN Quick start guide

Desa

Desa LMFP33NR Quick start guide

Desa

Desa FVMR18 Quick start guide

Desa

Desa VV36ENA1 Series Quick start guide

Desa

Desa CD36RN Quick start guide

Desa

Desa LMFP33NR Quick start guide

Desa

Desa VSGF36NR Quick start guide

Desa

Desa G42 Safety guide

Desa

Desa Design Dynamics VTD-18NV-JHB Quick start guide

Desa

Desa Comfort Glow CGCF26TN Quick start guide

Desa

Desa Vanguard VMH10TP Quick start guide

Desa

Desa Vanguard VGL450N Quick start guide

Desa

Desa Vanguard VSGF28NVA Quick start guide

Desa

Desa VsGF28nTF Quick start guide

Desa

Desa S36 Series Quick start guide

Desa

Desa VMH10TPB Specification sheet

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Miles Industries

Miles Industries Vogue 1300IRN Installation & operating instructions